Municipal Administration And Water Supply Department Tender

Fly Ash Brick work In CM 1:5 mix using best Fly Ash Bricks of size 230 x 110 x 70mm including finishing, curing etc., complete complying with standard specification.

Plastering with cement mortar 1:5 mix (one cement five P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

White washing Two coat with freshly burnt white shell lime in all floors including cost of lime, blue powder,fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification.

Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster ofparis, putty wherever required etc., complete as per standard specification

Paving the floor with 20mm thick Cement based Hydraulically Pressed Anti-Skid (EUROCAN) tiles (Pattern design) in cement mortar 1:3 [one cement and three M-sand] 20mm thick and pointed with same colour of cement etc., complete as per standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing in position of Aluminium anodised partition with 62x38x2mm extruded box section at bottom, vertical and horizontal members. The vertical members are spaced at 90cm c/c and to horizontal members are spaced at 1.20m, 2.10m and 2.40m height and the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick clear glass with necessary glassing clips, rubber beadings etc., including cost of labour for electrical consumption required for the fabrication, drilling holes in RCC columns with power drill to the required extent and make good to the original condition etc., complete and as directed by the departmental officers. The aluminium for frame to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns.

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish Single leaf door (with frame) half glazed and half PLB board using extruded aluminium section for frame and shutter with necessary accessories such as PLB 12mm thick, 5.50mm thick plain sheet glass, Alu. 'L' angles, Rubber beading, aluminium clips, best double action floor springs / door closer, handles, tower bolt, hinges, pivot and locks including labour and power consumption charges required for fabrication, if necessary chipping, dismantling, making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc., complete. The aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868 / 1962 of anodic film thickness of not less than 15 microns for all sections.

Interior Work Arrangemnets ( Computer table With draw & Lock Arrangements )

Removing & Refixing Glass ( With Cutting Work )

Supply and fixing FRP door shutter with frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of hold fasts and solid core FRP shutterPanel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., complete complying with standard specification