Municipal Administration And Water Supply Department Tender

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and Eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying water carrying with all leads of good water compacting and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38 (a) Column

Plinth Beam Grade Beam alround

Slab and Beam Lintel

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 Cum.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cum.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 Cum) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in CM 1:5 (one cement & five sand) using II nd class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing,etc., complete complying with standard specification

Brick partition walls using best quality using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with cement mortar (1:5),12 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed. -100Sqm S.I.333

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles,plates,sheets,fabrication charges,cost of hold fast and transportation charges etc.complete.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Manufacturing, supplying and fixing in positon of RCC Jally of 5cm thick in cement concrete 1:2:4 using 20mm machine crushed stone jelly (excluding cost of reinforcement steel) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed

Supplying and fixing in positon European Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Finishing the top of floor with Granolithic Finish with CC 1: 2: 4 (one cement, two sand & four HBG jelly) using chips of grade 10 mm and below for 25mm thickness and rubbed

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with ceramic tiles of sizes 300mm X 450mm X 8mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Supplying and fixing of 30mm thick Cudappah slab including cost and conveyance and all labour charges etc., complete.(2024-25 PWD SOR VOL I P No 21. Sl No M-0132)

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). (2024-25 Electrical SOR SD 23)

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.(2024-25 Electrical SOR SD 38)

Supply and Fixing of 1200 mm Ceiling fan includingn cost and conveyance of all materials and labour cherges etc complete.(SD-106)

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting SD 88

Labour charges for Painting TWAD Board Emblem in accordance with the size and specifications as approved by the Board on the Service Reservoirs including cost of all consumables, one coat of base paint, scaffolding charges including painting NRDWP Logo on the Service Reservoirs.(2024-25 TWAD SOR VOL II P No 195 Sl.No WD-W0745)

Painting and Drawing of Various art varities such as Jungle aniimals,Birds,Cartoon,Scenaries etc,with appropriate and matching colours including cost of all materials ,transportations and all other labour charges etc,complete.

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

Supply and fixing of PVC Pipe and specials including cost and conveyance of standard specification (a) 25mm PVC pipe (2024-25 PWD SOR VOL I P No 146 Sl.No M-876)

25mm PVC Elbow (2024-25 PWD SOR VOL I P No 147 Sl.No M-888)

PVC Screw Down Tap Heavy Type 15mm dia (2024-25 PWD SOR VOL I P No 87 Sl.No M-511)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Conducting the Geophysical survey, quality and quantity test and transportation charges etc., (This includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist.)

Drilling of borewell anywhere in Tamilnadu including transportation from one place to another place within Tamilnadu in alluvial soil or sedimentary strata of clay and sand or sand, stone, shale, pebbles, boulders etc., by first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia by direct or reverse rotatry mud and circulation method using Contractor’s rig, fuel, labour, drilling, betonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit (only Calyx drills are to be used)..(2024-25 TWAD SOR VOL II P No 201 Sl.No 14 WD -W 0834) 1428.79

Supply & Delivery of 200mm dia (Casing shallow depth up to 80m )PVC casing pipe as per IS 12818/2010 including all cost of labour charges etc,complete as per standard specifications.(2024-25 TWAD SOR VOL II Page No 6 Sl.No 1.1 WD-WD-M0030 )

Labour Charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including the jointing the pipes with PVC couplers with cement paste etc. complete.(2024-25 TWAD SOR VOL II P No 202 Sl.No b WD-W 0838) 362.30

Supply & Delivery of single phase 1.5 Hp Submersible Motor with out panel board 15LPMx10m with ISI Mark As Per IS 8034/2002 without Panel board including cost of all labour charges etc., complete as per standard specifications. (2024-25 TWAD SOR VOL II P No 101 Sl.No 2.0 WD M 1587)

Labour charges for the erection of submersible pumpset in bore well/open well including fixing and jointing submersiblecable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps,pressure gauges upto the exterior wall of pumproom and erection of panel board consisting of TPICN switches starter,Voltmeter,Ammeter,threepilot (indicating) lamp scapacitor single phasing preventor,water level guard and laying and jointing the cables and twin earthing as per IErules etc.,complete and testing the pumpset and trail run for 10 days. 7.50 HP Open well Motar.(2024-25 TWAD SOR VOL II Page No 204 Sl.No 17c WD -W 0871)

SINGLE PHASE PANEL BOARD WITH TWO LEVEL GUARD AND AUTO START 1.50 HP Supply and delivery of direct online starter confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/single Phase/50HZ(± 5%) and 230 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).(2024-25 TWAD SOR VOL II Page No 119 Sl.No 11.0 WD -M 1906)

Supply and Run of 2.5sq.mm 3 core flat type copper cable confirming to IS 694 / 1990 including all cost etc., complete as per standard specifications.(2024-25 TWAD SOR VOL II Page No 124 Sl.No 12.1 WD -M1974)

Supply & Delivery of PVC Pipe & specials etc., complete (a) 32mm dia UPVC Column pipe (2024-25 WAD SOR VOL II Page No 7 Sl.No 1.3 WD-M0049)

Nylone Robe for Borewell (2024-25 PWD SOR P No 112 Sl.No M1072)

200 mm dia Bore cover

Bore clamp set

32mm dia (1 1/4" ) GI Adopter As per 1239/Part I /90

32mm dia (1 1/4" ) GI Hex Nipple (2024-25 TWAD SOR VOL II P No 32 SI NO 5.1b WD M 0599)

32mm dia (1 1/4" ) GI Union (2024-25 TWAD SOR VOL II P No 32 SI NO 5.1b WD M 0603)

32mm dia (1 1/4" ) GI Tee (2024-25 TWAD SOR VOL II P No 32 SI NO 5.1b WD M 0595)

32mm dia (1 1/4" ) GI Coupling (2024-25 TWAD SOR VOL II P No 32 SI NO 5.1b WD M 0596)

32mm dia (1 1/4" ) GI Elbow (2024-25 TWAD SOR VOL II P No 32 SI NO 5.1b WD M 0594)

32mm dia (1 1/4" ) GM Gate valve (2024-25 TWAD SOR VOL II P No 33 SI NO 5.2 WD M 0618)