Environment And Climate Change Department Tender

Dismantling of existing PCC, Grano or Screed of any depth and removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Dismantling of existing RCC structures of all kinds and removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Dismantling of existing Floor finish and dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabs and removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Dismantling of existing Doors and Windows including removal of frames, hinges and fastenings without damages and handing over the same, removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Demolition of the existing toilet fittings (Cubicle, Wash counter, EWC, Urinals etc.,) & carrying the debris away from site as per architects / PM instruction. Cost to include chipping of the existing floor once the hard floor is removed to make the floor level and removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Grove cutting and dismantling the existing Grano as per the raceways marking and removing the debris etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Plain Cement Concrete, Centering, RCC and Steel works

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

For plane surfaces such as rectangular,square columns and chamfered sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins, facia Planter box, binders, basement, retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items.

Rate to include all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supplying, fabricating and fixing in position of steel Fe-550D grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required. Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Masonry Works

Providing and constructing cement concrete solid block masonry work at all levels in cement mortar 1:3 using standard size of 400 x 200 mm of solid cement concrete blocks of thickness as given below, with minimum compressive strength of 5 N / Sq.mm. conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. including all scaffolding, staging, curing, all lifts etc. complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. (Rate to include the column and fixing 200 mm long 50 x 4 mm hick MS bend to shape with anchor bolts at every fifth course the rate is inclusive of case of fabrication structural steel with all leads and lift) Note: All mortar to be machine mixed etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

200mm thick wall

100mm thick wall

Providing and constructing Autoclaved Aerated Concrete block masonry work in cement mortar 1:3 using standard size of 600 x 200 mm of AAC blocks. Blocks manufactured under strict quality control conditions confirming to IS standards only shall used a) Fixing the panels at all levels and supported on slab soffit with suitable arrangement including necessary staging, scaffolding arrangement, alignment and verticality (plumb level) of the walls. Rate Shall also include cutting necessary grooves / chases of required size and at required height for concealing electrical, plumbing, conduits / pipes, holdfasts, bolts etc. and making good surfaces after concealing work is complete. b) Grouting of cores in blocks to complete course for fixing of frames and all joinery works etc. complete, as directed. All materials required to carry out all related works including specialized work required around and above opening to receive the Frame and to ensure that the load of the panels are not transferred on to the frames or shutters of the doors, windows and ventilators so as to avoid bending of door frames/shutters and affecting the opening / closing operation of the door shutter. etc. complete and as directed. c) Finished work should be sand papered to receive plaster and any unevenness or undulations on the block should be made good by the application putty. d) If required to do so the test at an approved laboratory to ensure the compression strength of blocks confirming to IS standards. Rate shall include accessories for supporting the system into the ceiling with cleats & Anchor fasteners, scaffolding, loading and unloading, lead & Lift, Tools & Plants, curing, cleaning, pointing both sides, racking etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

For 200mm thick AAC block wall

For 150mm thick AAC block wall

For 100mm thick AAC block wall

Providing and constructing of brick work in Cement Mortar 1:5 (One Cement and Five M.sand) using best quality of Second Class Ground Moulded Chamber Burnt Bricks 9" x 4 3/8" x 2 3/4" with minimum compressive strength of 35 Kg per Sqcm for foundation and all floors including curing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". 230 mm thick

Providing and constructing of brick partition walls in Cement Mortar 1:3 (One Cement and Three Sand) using best quality Second Class Ground Moulded Chamber Burnt bricks of size 9" x 4 3/8" x 2 3/4" with hoop iron reinforcement if found necessary including curing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". 115 mm thick

Internal Plastering works

Plastering of 12mm thick plaster on internal surfaces of RCC/brick/block walls in cement mortar 1:5 (1 of Cement : 5 of P.Sand). Rate shall include for scaffolding, drip band / grooves of any size and shape, curing, surface preparation before the application of plaster, providing galvanized mesh to a width of 150mm at the junctions of masonry and concrete works, wherever conduits and pipes are concealed and packed in the wall; and also providing and fixing of galvanised corner beeds for all corners/ edges of columns and walls including tying in position by using suitable nails / clamps / screws and as directed etc. complete at all levels. Rate to include screening and washing of sand and all mortar for plastering to be machine mixed etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Plastering of 12 mm thick water proof plaster in Toilet internal walls and over head tank with CM 1:3 (1 of cement : 3 of P.Sand) with water proofing compound of CICO No:1 or equivalent as per manufacturer’s specification and roughening the surface in green condition with wire brush and clearing of loose particles with sponge brush (washed sand finish) etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and application of 10mm thick Perlite based Gypsum plaster on internal RCC wall, beam, block wall and Ceilings surfaces with Bulk density of 650-710 Kg/m3 and finesses of 95% passing through 150 micron. Rate shall be include for Surface Preparation, filling cracks in the background if any, surface cleaning/curing (if required), finishing of Electrical Switch Boxes, light points, DB’s etc. and necessary staging, scaffolding, GI edge beading, GI plaster mesh at all levels and elevations and also include cost of material, labour, unloading and shifting of material, water etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Internal Painting works

Providing and finishing the Existing Ceiling surface with necessary grinding, touchup plasteriing, POP works wherever required area to finish etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Preparing surface, Supply and application of first class POP punning plaster to a thickness of 6-10 mm over exposed plastered wall surface including scaffolding etc. complete. Rate to include for making the wall with plumb line and get smooth surface to receive the paint. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Providing and applying two coats of Acrylic emulsion paint with low of approved colour over a coat of water based primer including preparation of surface by thorough cleaning and applying two coats of premixed putty as per manufacturer’s specification fully to give an even shade before painting and curing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Walls and Partitions & Gypsum False Ceiling

Ceilings without putty

Providing and applying of Texture paint of approved make to walls of approved colour over a coat of primer as per manufacture specification. The rate shall be including preparation of surface by thorough cleaning and as per manufacturer’s specification fully to give an even shade as directed etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Price Rs 1200/Sqm

Supply and Application of real concrete finish of 1mm , Eco cement achieved by mixing cement and polymer on the desired base for internal walls, over a coat of water base primer and putty done surface. The final coat is achieved with PU sealer. The concrete is made breathable by using the right polymer proportion which makes the material non cracking. The rate shall include of material and application on the prepared surface without undulations by the painter etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost Rs 225 /sft

Providing and applying of two coats of Duco paint of approved colour and make over a coat primer including preparation of surface by thorough cleaning as per manufacturer’s specification fully to give an even shade and necessary metal paste putty as required. Rate shall be inclusive of wastage, scaffolding, spray equipment etc. measurement as per SP 1200 guidance etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: 250 / Sq.ft

Painting two coats with melamine polish of best approved quality complying with standard specification and approved quality etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Water Proofing Works

Supplying and filling the toilet area by BRICK-BATCOBA by adding CICO NO:1 or approved equivalent admixture including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with water proofing compound like CICO No.1 at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and laying water proofing treatment of Toilet, covering the following order and consisting of following operations. The Toilet slab shall be thoroughly cleaned to remove debris and dust . Making V Groove over the construction Joints & filling V Groove with CICO Quick setting Material admixed with Cement & Application of 2 coats of TAPECRETE - Acrylic Polymer Cementitious coating over well prepared surface , followed by a layer of plastering with cement mortar 1:3, 20mm thick admixed with CICO NO:1 @ 2% by weight of cement. (Treatment shall be given up to 1.5 M height around shower area and 1M height at all other vertical area above finished floor lvl) etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Flooring,Skirting and Dadoing Works

Providing and laying in panels not more than 20 sqm. in plan granolithic flooring with cement concrete 1:1.5:3 by using coarse graded aggregate of 6 to 12 mm size laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work. The screed shall be laid for effective separation of panels not exceeding 20 sqm in plan etc and Unevenness in floor finish shall not exceed +2mm in one square metre area. Including sprinkling of Nitoflor Hardtop Standard evenly a shake on a ready mixed non-metallic monolithic floor hardening compound with very hard granulates of mineral origin over concrete floor when the concrete in green and touch dry condition at the rate of 5 Kgs/Sqm. Nitoflor Hardtop Standard shall possess a compressive strength of 50N/mm² as per IS: 516-1959, Moh's hardness not less than 8, as per specification and instructions of the manufacturer. Rate to include lead , lift at all levels, pumping, placing, necessary formwork, curing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Average 70 mm thick.

Average 50 mm thick.

Supply and Laying flooring with best quality of Granite slab leather finish 18 to 20mm thick size not less than 1200 x 600 mm machine cut with approved pattern in a single colour/multiple colour and set in C.M 1:4 (1 of cement : 4 of sand) 20 mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern, including finishing the joints with matching shade, cement slurry, cutting, edge chamfering and polishing rough, medium, nice and tin-oxide polish. Rate shall include wastages, preparation of base surface, cleaning, acid wash over the finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over, work at all levels etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Extra for pre finished nosing to treads of steps, counter, ledge wall top of Granite stone etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Providing and fixing of flooring with quality approved make of Glazed Vitrified Tiles (GVT) - (seamless joint) confirming to IS 13006/EN 176 Group B1a with technical specification as Mohs scratch hardness minimum 7, Water Absorption of less than 0.5%, Modulus of Rupture greater than 35 N/mm2, Deep Abrasion resistant maximum 175 mm 3 Surface flatness, Straightness of sides ± 0.25%, thickness ± 5% of size of approved colour and size & thick as specified below, set in 20mm thick C.M.1:4(1 cement and 4 manufactured sand ) and pointing with white cement to matching colour shade as per Manufacturer's Specification and as directed. Rate shall include wastages, for preparation of base surface, cleaning, acid wash, and finished surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over, work at all levels and as directed. Rate shall be inclusive of forming pattern etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Size of tiles are as follows.

600x600x9mm

1200 x 600 x 9mm

Providing flooring with best quality approved make Anti Skid Ceramic tiles ranges, from approved make to the pattern as shown in the Architectural Drawing. The size of tile shall be as per the samples approved, set in CM 1:4, 20mm thick and pointing the joints with white cement to matching colour shade as per Manufacturer's Specification and as directed. Rate shall include for preparation of base surface, and finishing the surface, cleaning the surface, and protecting with Gypsum / POP layer over Plastic sheet and removing the same before handing over, work at all levels etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Size of tiles shall be 600mm x 600mm x 6 to 7mm.Basic Cost - Rs 60 / Sft

Supply and laying with best quality the following materials of Machine Polished granite slab for counter / wash basin counter top of 18 mm thick (Jet Black) including cutting for wash basin and edge polishing to be set in CM 1:4 (1 of cement : 4 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish and providing the hole in the granite for fixing the pillar cock tap etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: Rs 150 / Sft

Providing Sill and Ledge coping with granite of approved shade and to a thickness not less than 18mm, set in cement mortar 1:4 and joint finish with approved grout of matching shade, as per Manufacturer's Specification. Rate shall include for cutting, bull nosing, chamfering, polishing, preparation of base surface, joint finish with approved grout etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: Rs 130 / Sft

Supplying and laying for flooring with White Marble slab (Adanga) not less than 18mm thick set in appropriate Laticrete adhesive as per approved pattern/design drawing using irrespective of size and shape, including finishing the joints with Laticrete make to matching colour shade. Rate shall include for preparation of base surface, cutting, edge chamfering and polishing rough, medium, nice and acid wash and tin-oxide polish as per manufacturer's Specification and as directed. Rate including all materials, labour charges, working at all levels, loading, unloading, preparation of base surface & finished the surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over,work at all levels etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect"

Italian Marble flooring Providing flooring with A grade quality approved colour Italian Marble not less than 20mm thick and sizes not less than 1200x900mm / 900x600mm, machine cut and machine high pre-polised, set combination of Laticrete adhesive L 111 and L 73 ( Cemetitious powder and latex rubberized liquid) or euivalent approved make to a thick not less than 9mm (for surface contact of the bottom of the granite slab) as per approved pattern / design using irrespective of the size and shape, including finishing the joints with Laticrete make Unsanded Cementitious grout L 600 serious or equivalent all as per manufacture's specification and as directed. Rate shall include for preparation of base surface & finished with required level of polishing to the surface, protection with gypsum / pop layer over plastic sheet and removing the same before handing over, work at the all levels and as directed. The tolerance in level shall be +/-1mm. Basic cost Rs 8000/sqm

Supply and Laying Glazed Vitrified Tiles (GVT) skirting - 100 mm high of same approved flooring tile set in C.M 1:3 (1 of Cement : 3 of manufactured sand) 12 mm thick and pointing the joints with white cement compound and matching corner tile beading etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost - Rs 80 / Sft

Providing and fixing of Modular Skirting over partition, columns and walls with all accessories. The screws anchored should be recessed and covered with gaskets. Rate should include Covers at corners & ends, screws, wall chipping, plastering, punning., complete at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Anodized Aluminum skirting with 50mm height Basic cost: Rs 150 / Rmt

Anodized Aluminum skirting with 75mm height Basic cost: Rs 175 / Rmt

Anodized Aluminum skirting with 100mm height Basic cost: Rs 210 / Rmt

Supply and Fixing Dadoing with best quality polished vitrified tile of approved make set in C.M 1:3 (1 of Cement : 3 of manufactured sand) 12 mm thick and pointing the joints with white cement compound and matching corner tile beading. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportation charges, loading, unloading, chasing of wall for flushing the tile inline with wall surface, preparation of surface, necessary hacking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect" (Toilet - size of Tiles shall be - 600 x 600 x 9mm Basic Cost - Rs 80 / Sft).

Providing Dadoing with best quality Ceramic tile of approved make and size set in cement mortar 1:3 (1 of Cement : 3 of manufactured sand), pointing the joints with white cement compound and matching corner tile beading. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportation charges, loading, unloading, chasing of wall for flushing the tile inline with wall surface, preparation of surface, necessary hacking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum/Pop layer over Plastic sheet and removing the same before handing over etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect" (Kitchen & dish wash-Size of Tiles shall be-600 x 600mm x 6 to 7mm).Basic Cost-Rs.50/Sft

Supplying and installation of Modular Carpets made with 100% nylon 6 or 6.6 manufactured using digital injection or 100% solution dyeing process. The carpet should have protective treatment for soils, stains and anti microbial additives. The backing shall be with either PVC free PU underscore cushion or recyclable / recycled PET hard backing as per manufacturer's specification and as required by the Engineer-in-charge/Architects/Clients/PMC. Carpet to meet ARR - Severe Rating as per CRI TM 101 and CRI LEED certified. The installation of carpet should be with green adhesive of approved make, all complete as per manufacturer's specifications. Working at all levels and heights etc. The laying pattern should be as per Architect's inputs and approval etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". The quoted rate shall be inclusive preparing the surface and laying of carpet tiles optimized for glue-free installation with tactile connectors or with adhesives virtually VOC less than 50 grams/ litre for fixing over existing flooring as per Manufacturer's specification. Method of Measurement: "Supply and Installation: Actual laid area will be measured and paid as per the site conditions under the respective items. Attic Stock: Number of factory packed cartons handed over to Clients / PMC which will be measured in Sqm, under the respective items." Warranties: Carpets should have minimum 15 Years warranty against Delamination of backing, Stain resist, antistatic, face fiber wear, dimensional stability, flaAlbansbility, tufted bind, colourfastness to light and atmospheric contaminants etc., Vendor Should submit warranty certificate satisfying the above criteria.

Basic Cost: 150 / Sq.ft Shape and Size - Square / Plank Construction - Tufted Surface Texture - Textured Patterned Loop / Texture Loop Multilevel Pattern cut /loop pile / Random Tipshear Tufted Face Weight: Not less than 18.0 oz./yd2 Stitches per inch: Not less than 9 Gauge: 1/12" Finished pile thickness: Not less than 0.1" Average Density: In the range of 6000 oz./yd3

Basic Cost: 185 / Sq.ft Shape and Size - Square / Plank Construction - Tufted Surface Texture - Textured Patterned Loop / Texture Loop Multilevel Pattern cut /loop pile / Random Tipshear Tufted Face Weight: Not less than 18.0 oz./yd2 Stitches per inch: Not less than 9 Gauge: 1/12" Finished pile thickness: Not less than 0.1" Average Density: In the range of 6000 oz./yd3

Supplying of 2% Attic stock of carpet. Attic stock has to be handed over to Clients in factory packed condition. Attic stocks to be rounded off to the nearest Square meters that will be accommodated in factory packed cartons etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: 150 / Sq.ft

Supplying of 2% Attic stock of carpet. Attic stock has to be handed over to Clients in factory packed condition. Attic stocks to be rounded off to the nearest Square meters that will be accommodated in factory packed cartons etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: 185 / Sq.ft

Supplying and installation of 4.5mm thick Luxury Vinyl flooring of approved make and shade over the existing self leveled floor. The fixing to be done with VOC free water based adhesives and to be laid as per manufacturers methodology. The rate shall include all cuttings, wastages, cost of all materials adhesives, skirting, cleaning the surface, making dust free, including all the materials and labour mentioned above for complete finished work. Only laid area will be measured for payment etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Rate - Rs 300 / Sft

Supplying and installation of 2.0mm thick Anti static Vinyl flooring of approved make and shade over the existing self leveled floor. The fixing to be done with VOC free water based adhesives and to be neatly welded as per manufacturers methodology. The rate shall include all cuttings, wastages, copper strips, cost of all materials adhesives, including welding of joints, cleaning the surface, making dust free, including all the materials and labour mentioned above for complete finished work. Only laid area will be measured for payment etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Price : Rs 175/ Sft

Providing, laying Self Leveling Compound for Vinyl Flooring to average 3mm to 4mm thickness using self leveling compound of approved make below the Vinyl flooring for achieving the smooth, hard and absolutely leveled surface is made available to avoid undulations in the top flooring. The Self leveling shall be laid in accordance with the manufacture guidelines using the tools and accessories recommended, complete as per the drawing at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Location: Base for Carpet, Sports flooring, Luxury vinyl and Anti static vinyl flooring

Providing and laying self leveling three component pigmented Epoxy joint less floor topping "Shalideck - SL " - 750 microns or approved equivalent make, over granolithic flooring as per manufacturer's specification. Rate shall includes 100 mm height of wall skirting and including preparation of surface, application, wastage, equipment, tools and plants, work at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supplying and laying of 15mmthk Mikasa Real wood flooring (Walnut) with underlayment of 2mm thk as per manufacturer's specification, Rate shall includes 100 mm height of wall skirting and including preparation of surface, application, wastage, equipment, tools and plants work at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basi cost: Rs 520 / Sft

Supplying and laying of 15mmthk Mikasa Real wood flooring (OAK) with underlayment of 2mm thk as per manufacturer's specification, Rate shall includes 100 mm height of wall skirting and including preparation of surface, application, wastage, equipment, tools and plants work at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basi cost: Rs 430 / Sft

Providing and fixing of Access floor systems of approved make confirming to PSA MOB - PF2 PS/SPU, BS 476 - Part 6, ASTM E84 1998 and ASTM E136 System: Access floor system to be installed shall provide a maximum finished floor height as mentioned below. The system shall provide suitable pedestal and under-structure designed to withstand various static loads and rolling loads. The entire Access floor system shall provide adequate fire resistance, acoustic barrier and air leakage resistance. Panels : Access Floor panel of size 600x600 mm shall be all steel welded construction, with an enclosed bottom pan of 64 hemispherical cones and top plain sheet which are fuse welded at minimum 81 locations to form a panel of an overall depth of minimum 29 mm. The inner empty core of the panel is injected with a light weight fire retardant, non combustible cementitious compound at high pressure to fill in all the crevices of the panel and ensures support of not less than 85% of the top surface area of the panel. The panel after cleaning, degreasing, phosphate by 7 tank process is coated with minimum 40 micron epoxy coat and is heated to achieve maximum adhesion and surface resistance. The Panels shall be UL listed / FM approved. The panel is either bare finish or laminated with 1.5 mm thick fire retardant floor grade antistatic laminate / pvc on a semi -automated lamination line to ensure maximum bonding to the steel surface. The edges of the laminated/PVC are protected with black PVC edge trim 5mm wide on all sides. This edge trim is mechanically locked and sealed in place to avoid detachment. Pedestals : Pedestal installed to support the panel shall be suitable to achieve a finished floor height as mentioned below. Pedestal design shall confirm speedy assembly and removal for relocation and maintenance. Pedestal base to be permanently secured to position on the sub floor. Pedestal assembly shall provide for easy adjustment of levelling and accurately align panels to ensure lateral restrain. Pedestals shall support an axial load of 2000 Kgs, without permanent deflection and an ultimate load of 3500 Kgs. Pedestal head shall be designed to avoid any rattle or squeaks. Pedestal Assembly : Consisting of 100 x 100 x 2mm thick galvanized epoxy polyester coated MS Base plate die-pressed orbitally riveted to a 21mm O.D. 2.5mm thick epoxy coated MS pipe to engage the pedestal head assembly. The pedestal head assembly consists of an embossed steel plate having 4 holes with ¼ the tapping for fastening and locating of tile ; orbitally riveted to a corresponding threaded stud 16mmdia. (O.D), length 100mm which is designed to engage the pedestal base assembly. The assembly shall provide a range of height adjustment upto 25mm, with the help of check nuts. Under structure : Under structure system consists of stringers of size 570 x 32x 20 x 1.5mm to form a grid of 600 x 600mm. These stringers are locked into the pedestal head and run both ways. The US system shall provide adequate solid, rigid and quiet support for access floor panels. The US system shall provide a minimum clear, uninterrupted height of 350 mm minimum, between the bottom of the floor and bottom of the access floor for electrical conduiting and wiring. Stringers : Stringer system is all steel construction, rectangular channels 30 x 20 x 1.6mm thick with pre-punched counter sunk holes at both ends for securing the stringers onto the pedestal head ensuring maximum lateral stability in all directions. The grid formed by the pedestal and stringer assembly shall receive the floor panel. "Panel Loading: The panel dimensions and performance must confirm with PSA MOB - PF2 PS/SPU standards for a heavy duty panel and must comply with the, Concentrated Point Load : 360 kgs on a 25 x 25 mm square on the center of the panel with a maximum permissible deflecting of not more than 2.5mm & Uniformly Distributed Load (UDL): 1650 kg/M2 with a maximum permissible deflection of not more than 2.0mm. Fire Rating : The Panels shall confirm to Class O & Class 1 Fire Ratings tested as per BS 476 Part 6 & 7" Rate shall include to produce a test certificate for the above load of approved laboratory, preparation of surface, cutting for supply / return Air Grills and for Grommet of required size, wastages, lead & lift, grouting the system with anchor fastener, removing all debris from the premises etc. and for providing and applying of 500 micron Epoxy painting as a sub floor insulation to the entire area of existing floor(Below false flooring) as per manufacturer's specification etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

To a height of 300mm with Antistatic HPL finish

Joinery Works

Providing and fixing of factory finished solid Beech Wooden door Frame as per drawing detail. All the wooden surfaces to be sanded to required level, treated with wood putty and finished with PU polish to the satisfaction of Architects / Client. The wooden frame to be treated and should be resistant to borer, termite and fungus. The rate shall be inclusive of making necessary design as per drawing, in the frame and necessary Hilti fastener and hardware etc,.complete., Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Finishes shall made at Factory only installation at site. Material : 2nd Quality

Finished with PU polish

Finished with a coat of wood primer and two coats of wood enamel paint

Supplying and fixing Door Frames using Teak Wood of quality and size as per the specification/drawings attached including planning, providing plaster groove, form pockets in Blockwork / fixing anchor fasteners from Hilty or Fischer in RCC, fixing necessary Z clamps made out of 40x6mm MS Flat of 400mm long in frame, fixing frame in position, grouting the pockets using CC 1:1:2, applying two coats solignum paint on surface frame butting on masonry, applying one coat wood primer etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect" Material : 2nd Quality

Supply and Installation of 35mm thick Flush door shutters with or without Vision panel, made of solid core block board type bonded with synthetic resin thermo pressed with 1.5 / 2mm thick PVC edge beading of approved shade. Synthetic resin to comply with IS 848 -2006. The construction procedure of the shutter should be as per IS:2202 - Part1 and 2 and should be fully organic preservative treated as per IS 401. The shutter shall be shop prepared for taking mortise lock or latches suitable with block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock, covered in IS:2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc.; complete as directed. The vision panel to be with toughened glass and wooden beadings, all around finished with approved colour paint. Both sides of the door shall be finished with either 4mm thick Veneer or 1.5 mm thick laminate of approved color / pattern. Rate to include installation of door, laminate and veneer with PU polish, necessary accessories for fixing for complete installation., Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect"

Basic Cost of laminate : Rs 75 / Sft

Basic Cost of Veneer : Rs 180 / Sft finished with PU Polish

Glass Door - With Stile Supply & Fixing of Aluminium Glazed Door (Single / Double Leaf) with Glass infill of 10mm thick toughened glass with -100 frames Stiles all around the door. Aluminium Stile to be formed out of 100x45mm of Door Profile frame with clips & seals. For doors part of single/double glazed partiton DP100-SG/DG Door rebate profile to be used. "In case of Glass overall panel OHPDP100-SD/DG Over Panel Door profile to be used.The profiles shall be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system.All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing etc., Complete complying with standard specifications and as directed by the ""Engineer-in-charge/Architect"". NOTE: Hardware will be measured seperately and paid under relevant BOQ items."

Single Door - 900mm x 2400mm

Single Door - 1000mm x 2400mm

Single Door - 1200mm x 2400mm

Double Leaf - 1800mm x 2400mm

Supply and fixing of Fully glazed Fire rated -Single leaf Door using Two hours fire rated fully glazed Door frame (including necessary accessories / packing) & SGG Contraflam Doorlite 11mm (EW 120) Dormakaba BB Hinges - 4"x3"x3mm - 4nos TS 92 Door Closer with G-N EN 2-4, B/G - 1no TGDI D type Offset Pull Handle 450 x 25 mm, CTC - 450 mm, D - 25 mm - 1no Narrowstile Dead Lock Backset - 25mm - 1no

Single Door - 1000mm x 2400mm

Single Door - 1200mm x 2400mm

"Supply and fixing of Fully glazed Fire rated -Double leaf Door using Two hours fire rated fully glazed Door frame (including necessary accessories / packing) & SGG Contraflam Doorlite 11mm (EW 120) Dormakaba BB Hinges - 4""x3""x3mm - 8nos TS 92 Door Closer with G-N EN 2-4, B/G - 2no TGDI D type Offset Pull Handle 450 x 25 mm, CTC - 450 mm, D - 25 mm - 2no Narrowstile Dead Lock Backset - 25mm - 1no Flush bolt - 2 nos " Double Leaf - 1500mm x 2400mm

"GEZE EC turn automatic swing operator for wooden door single leaf for specially abled toilet application. Proving and fixing of GEZE ECturn Automatic single-leaf Swing Door drive for the supplied single-action door by others, as low-noise electro-mechanical door drive for internal doors, height of drive only 60mm, the drive tested in accordance with DIN 18650, with mounting plate, for door weights up to 125 kg & up to 1100mm width, with Automatic configurable, with Optional battery to be able to guarantee automatic opening and closing even in the event of a power failure. GEZE button program switch for operating mode selection, with function keys, LED-dot display and coded error display, protection class IP40. Operating modes: off, continuous open, automatic operation, one way, night lock. Low Energy operation in accordance with DIN 18650, Detection of obstacles and reversing, Diagnostic function and error memory, all settings directly at the drive or via display programme switch possible, Cover hood in colour anodized EV1." "GEZE safety sensor strip, mounted on the door leaf, to secure the swinging area of the door in opening and closing direction can be connected without additional board. (two units are required for each door leaf). Technical features: Dimensions: 60 x 60 x 580 mm (HxDxW), mains connection: 230/110 V AC, 50/60 Hz, door width: max. 1100 mm, door weight: max. 125 kg, door opening angle: approx. 115°, opening and closing speed adjustable, hold-open time adjustable from 0 to 30 seconds contour-controlled opening and closing" "Moving panel: Swing door leaf with accessories for wooden door GEZE Elbow Switch to activate & slide the door. GEZE Active infrared light curtain safe guards of swing door. It is mounted on the door leaf, to secure the swinging area of the door in opening and closing direction. (two units are required for each door leaf). Switch unit inside with LED to indicate occupied. (switch with lamp inside and one lamp will be outside )This switch activates and deactivates both inside and outside elbow switches. Incase of Emergency, the occupier not able to reach or access the door from inside, Emergency Opening Device , which is fixed outside, will enable the door to open from outside. Pull switch provided incase of emergency, occupier falls down, by using pull switch ,which is connected with sounder, they can get attention of the maintenance staff for assist GEZE Mechanical programme switch MPS-ST. For setting the operating mode of automatic doors with key, LED error display, rating IP 40. suitable for switch ranges with 55x55mm switch insert. Note: Doors by others Necessary reinforcement to be provided for operator & guide rail fixing Leaf width 650-1100mm"

"GEZE EC turn automatic swing operator for wooden door single leaf for specially abled toilet application. Proving and fixing of GEZE ECturn Automatic single-leaf Swing Door drive for the supplied single-action door by others, as low-noise electro-mechanical door drive for internal doors, height of drive only 60mm, the drive tested in accordance with DIN 18650, with mounting plate, for door weights up to 125 kg & up to 1100mm width, with Automatic configurable, with Optional battery to be able to guarantee automatic opening and closing even in the event of a power failure. GEZE button program switch for operating mode selection, with function keys, LED-dot display and coded error display, protection class IP40. Operating modes: off, continuous open, automatic operation, one way, night lock. Low Energy operation in accordance with DIN 18650, Detection of obstacles and reversing, Diagnostic function and error memory, all settings directly at the drive or via display programme switch possible, Cover hood in colour anodized EV1." "GEZE safety sensor strip, mounted on the door leaf, to secure the swinging area of the door in opening and closing direction can be connected without additional board. (two units are required for each door leaf). Technical features: Dimensions: 60 x 60 x 580 mm (HxDxW), mains connection: 230/110 V AC, 50/60 Hz, door width: max. 1100 mm, door weight: max. 125 kg, door opening angle: approx. 115°, opening and closing speed adjustable, hold-open time adjustable from 0 to 30 seconds contour-controlled opening and closing" "Moving panel: Swing door leaf with accessories for wooden door GEZE Elbow Switch to activate & slide the door. GEZE Active infrared light curtain safe guards of swing door. It is mounted on the door leaf, to secure the swinging area of the door in opening and closing direction. (two units are required for each door leaf). Switch unit inside with LED to indicate occupied. (switch with lamp inside and one lamp will be outside )This switch activates and deactivates both inside and outside elbow switches. Incase of Emergency, the occupier not able to reach or access the door from inside, Emergency Opening Device , which is fixed outside, will enable the door to open from outside. Pull switch provided incase of emergency, occupier falls down, by using pull switch ,which is connected with sounder, they can get attention of the maintenance staff for assist GEZE Mechanical programme switch MPS-ST. For setting the operating mode of automatic doors with key, LED error display, rating IP 40. suitable for switch ranges with 55x55mm switch insert. Note: Doors by others Necessary reinforcement to be provided for operator & guide rail fixing Leaf width 650-1100mm" Supply and Installation of minimum Two hours fire rated Hollow metal doors from ISO 9001-2000 certified approved Manufacturer. Fire door should be manufactured and tested in accordance with IS 3614 Part 2, BS 476 Part 20 & 22 for stability and integrity and pressed galvanized steel confirming to IS 277. Fire door shall be tested and certified by a third party evaluation program from approved international agency like CERTIFIRE or CBRI / ARAI and labeled for maximum rating of 2hrs. Labeled doors with certification shall be with vision glass as a part of complete assembly. Manufacturer test certificate shall cover doors both single and double leaf and all doors supplied shall be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Door frame shall be single / double rebate profile with minimum size of 100 x 55mm made out of minimum 1.60mm (16gauge) thick galvanized steel sheet. Frames shall be mitered and field assembled with self tabs. Frames to have either inbuilt grooved sealing system with fire rated EPDM gasket as standard or shall be without inbuilt groove and sealing to be done as listed in hardware schedule. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Additional reinforcement pads to be provided for hinge jamb, strike jamb and mortar guards. Frames should be provided with minimum 3mm back plate bracket, minimum 6 numbers of anchor fasteners for single leaf and minimum 8 nos anchor fasteners for double leaf doors of minimum 8mm dia, 80mm long for installation on a finished plastered masonry wall opening. Once frame installed should be filled with Fire resistant Polyurethane foam as approved by Client / PMC. After filling the frame, the holes in the frame should be sealed with insert plug as per manufacturer's specification. Door leaf shall be minimum 46mm thick fully flush double skin uninsulated door with minimum 5mm thick fire rated vision lite. Door leaf shall be manufactured from minimum 1.2mm (18guage) thick galvanized steel sheet. The internal construction of the door should be provided with rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and should be provided with necessary reinforcement for receiving hinges, locks, and door closers. The edges should be interlocked with a bending radius of minimum 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. All doors and frames shall be finished with polyurethane aliphatic grade powder coating minimum 50 microns of approved colour. The door leaf and frame shall have passed minimum 500 hours of salt spray test. Shop drawings with all the fabrication and hardware details to be submitted for Architects approval, before fabrication. Quoted rate to include all the works mentioned above for complete installation of doors. Working at all levels and heights and as directed by Engineer- in- Charge. Necessary Test certificates to be submitted and Quoted rate to include for testing the samples of approved size with hardware, specific to this project. For all access control fire doors with Electric locks, necessary provision to be made for routing of cables. Vendor to get inputs for location of doors from client before procurement etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". The door sizes shall be as follows

Single Door - 900mm x 2400mm

Single Door - 1000mm x 2400mm

Double Door - 1500mm x 2400mm

Double Door - 1800mm x 2400mm

Specification same as above, but for Shaft doors with single rebate and Frames all around Including allen key set.

Single Door - 750mm x 1500mm

Single Door - 600mm x 1500mm

Supplying and installation of hardwares for the fire door, Flush Doors, glass doors etc, with necessary accessories. All the Hardware should be Fire rated , CE marked and Certifire approved for Fire rated doors of Dorma or equivalent makes. The hardware details are listed below "All the hardware for BS standards doors must comply with the following European standards etc., Complete complying with standard specifications and as directed by the ""Engineer-in-charge/Architect"". Door Closer - As per EN 1154 - 500000 cycles tested Locks - As per EN 12209 - 200000 cycles tested Hinges- As per EN 1935 - 200000 cycles tested Lever Handle - Confirms to EN 179 and EN 1906 - 200000 cycles tested Panic Bar - Confirms to EN 179 and EN 1125 - 200000 cycles tested PU Foam - tested according to EN1366-4 Door Gasketing seals to confirm BS EN 1634-3"

BB 4330 BB Hinges 4"x3"x3mm

BB 3090F BB Hinges 4"x3"x3mm

Flush Hinges 5"x3"x3mm

TS 90 Door Closer with hold open

TS 91 Door Closer with hold open

TS 92 Door Closer with hold open

SR 390 door co-ordinator for double doors surface mounted, zinc-plated, with MK 397, carry bar

Floor Mounted Door Stopper Half Dome

Pull Handle 22 x 300mm D Type

288A Dead Lock Package

PHA 2000 Single Point Locking Panic Bar

External Trim with Half Cylinder

Offset Pull Handle 25x450mm

Offset Pull Handle1050 x 32 mm TGDI D type

917 Narrow Stile Lock Package

Pure 8100 Lever Handle

271 Mortise Lock

60mm - EPC one side key other side thumbturn

Mortice Shaft Dead Bolt 57 mm backset

Flush Pull

Manual Flush Bolt - 300mm

Manual Flush Bolt - 600mm

Raven Door Seal - Single Leaf

Raven Door Seal - Double Seal

Drop Seal - 920mm

Drop Seal - 1070mm

Drop Seal - 1220mm

Partitions and Panelling Works

Providing and fixing of Aluminium base frames as shown in the Architectural Drawing for full height solid drywall partitions, suspended partitions and cladding with Aluminium extruded box sections of size 50 x 25mm x 1.5mm thick in both horizontal and vertical direction at 600 mm c/c spacing. The framework to have 25 x 25x 1.5mm GI 'L' angle cleats fixed to Aluminium box section at the top and bottom. All the vertical frames shall be continuous and should be anchored to the floor and soffit of slab. Alternate vertical frames should be anchored to the soffit of RCC slab with additional 'Y' supports. The cost to include necessary hardware as required to complete the works as per the manufacturer's specification. Actual laid area will be measured and paid. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". "Note: 1.Actual laid area will be measured and paid. Doors, glass panels and Windows provided in the partition the area will be deducted. 2. No deductions for service penetrations. 3. Rate to include additional supports for large service openings. 4. Applying acoustic sealant between the floor and floor sections / Ceiling and ceiling sections 5. Necessary Aluminium box section backing to be provided for handing the soft board / white board panels. 6. Vendor to quote only for frames along with accessories as described above. First and second skins will be given under relavent item. 7. Rate to include for curve/ circular and any other shape etc.,"

Partitions and Suspended partitions

Column and Wall paneling

Supply and Installation of Dry wall partition as shown in the Architectural Drawing to the thickness and height as mentioned below. But generally the partition shall be with GI stud, flooring and ceiling channels with two layer of tapered edge gypsum board (conforming to IS 2095 Part 1 : 2011) fixed with GI studs on both sides. All drywall partitions should have the duty ratings as specified under BS 5234 part 2. The detail specifications and methodology are listed below. Floor and ceiling channel made of GI steel to be anchored to the floor and true ceiling using HILTI HLC8x40 / HILTI X - GN20MX anchor fasteners at 600mm c/c in zigzag manner. Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. The gaps between floor and flooring channel, true ceiling and ceiling channel should be covered with fire sealant. C stud of 0.5mm thick having one flange of 34mm and another flange of 36mm made of GI Steel to be placed at the spacing specified below, in between floor and ceiling channel. Stud and floor channel are crimped together with crimping tool. Noggin channel of suitable width and 0.5mm thick having two flanges of 40mm each has to be provided at the horizontal joints of outer layer boards screw fixed to the studs using metal to metal flat head screws. 50mm thick Mineral wool or polyester wadding of density not less than 48 kg/m3 shall be placed in metal framework. Holding clip should be used to hold polyester wadding in its position. The gyp boards are to be fixed with Drywall Screws of 25mm and 50mm at minimum spacing of 300mm at Centre and 150mm at periphery of wall to either side of the stud. The gyp boards to be placed vertically to the framework, with joints staggered to avoid leakage through joints. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing compound confirming to ASTM C 475 and fibre mesh joint tape as per the manufacturer's specifications. Joint finishing to be done for both 1st and 2nd layers of gyp board All the GI channels and sections should be finished with minimum 120 GSM as per IS 277. Coating with AZ150 as per IS 15961 will be added advantage. All dry wall screws should be made of Carbon steel confirming to EN-ISO 7049/50 and finished with Case hardened Grey Phosphating CLASS 48 as per EN 14566. All metal to metal screws should be made of Carbon steel confirming to EN-ISO 7049/50 and finished with minimum Zinc Coating Thickness of 4.14micron. "Note: 1. The junction of the partition with masonry and all penetration through the partition has to be treated with Hilti/Pyroplex acoustic sealant. 2.Vendor has to submit detail specifications with shop drawing for approval. 3. No Deductions for the horizontal service penetrations. 4. Deductions to be considered for Doors and Windows. 5. Control Joint has to be provided at every 10 Mtr. c/c. along the length of wall. 6. Necessary GI stud backing to be provided for handing the soft board / white board panels. 7. Thickness of partition, size of stud and channel to be as listed below 8. The supplier / manufacturer should submit a guarantee certificate for required acoustic performance and stability. 9. The supplier / manufacturer should inspect the site to ensure that the executed works are adhered to the specification and should submit a guarantee certificate for required acoustic rating. 10. Mineral wool or polyester wadding will be paid separately under respective items. 11. Rate to include for curve/ circular and any other shape etc.," "Rate to include providing GI angle bead at all L-Junctions of partition, Nogging channels at the horizontal joints of each boards, GI stop beads around the door openings, providing necessary GI sections backing / Cutting for switches and sockets, additional supports near the openings, wood inserts for fixing joinery, necessary sound deadening membrane to achieve the required acoustics etc., Quoted rate to be inclusive of all the works mentioned above with standard drywall partitions accessories. Actual laid area from floor to true ceiling will be measured and paid. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the ""Engineer-in-charge/Architect"". " Note: To quote only for GI Sections with necessary accessories as mentioned above

With 50mm floor and ceiling channels and 48mm C stud placed 610mm c/c to a maximum height of 3.6 meters

With 72mm floor and ceiling channels and 70mm C stud placed 610mm c/c to a maximum height of 4.5 meters Note: To quote only for Gypsum boards along with necessary accessories as mentioned in the above description for dry wall partition / paneling works

First skin / Second Skin : Providing and Fixing of Gypboard to the Aluminium / GI partitions and the joints between the gyp-boards are fixed with 25mm drywall screws at 300mm center to center and are finished flush with jointing compound and paper tape, top coat, necessary accessories and all as per manufacturer’s specification etc. complete and as directed. Rate inclusive of fixing with necessary accessories, cutting for switches and sockets, necessary GI backing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Mode of measurement - Actual laid area will be measured and paid. Deduction will be made for Writing board / Soft board in the second skins. Note: The second layer should be fixed in staggered pattern to keep away the joints of first and second layer.

12.5mm thick plain gypsum board of density not less than 640 kgs /m3

12.5mm thick MR gypsum board with density not less than 760 kg/m3

12.5mm thick high density gyp board with density not less than 960 kg/m3 - Habito or approved equivalent

First skin / Second Skin : Providing and fixing of exterior grade MDF board., with 25mm drywall screws at 300mm center to center to the Aluminium/ GI Sections in staggered pattern. The joints to be smoothly finished without undulations. Rate inclusive of fixing with necessary accessories, cutting for switches and sockets etc. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

6mm thick

8mm thick

12mm thick

18mm thick

Specification same as above but the partition shall be of partition / curved partition / circular column paneling with flexi ply of 4mm thick instead of straight etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

First skin / Second Skin : Providing and fixing of Ply board., with 25mm drywall screws at 300mm center to center to the Aluminium/ GI Sections in staggered pattern. The joints to be smoothly finished without undulations. Rate inclusive of fixing with necessary accessories, cutting for switches and sockets etc. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

6mm thick

8mm thick

12mm thick

18mm thick

25mm thick

First skin / Second Skin : Providing and fixing of exterior grade BWR ply., with 25mm drywall screws at 300mm center to center to the Aluminium/ GI Sections in staggered pattern. The joints to be smoothly finished without undulations. Rate inclusive of fixing with necessary accessories, cutting for switches and sockets etc. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

6mm thick

9mm thick

12mm thick

16mm thick

19mm thick

Providing and fixing of 1mm thick laminate as shown in the Architectural Drawing from approved color and shade with grooves and lines and in patterns on specified area as instructed by Architect / Client. The cost of necessary hardware's, adhesives, wastages etc., as required for complete the works. Actual visible surfaces only will be measured and paid. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

1mm thick laminate of approved color and shade with Basic Cost - Rs. 60 /sq.ft

1mm thick laminate of approved color and shade with Basic Cost - Rs. 75 /sq.ft

Providing and fixing of 4mm thick veneer as shown in the Architectural Drawing from approved colour and shade with grooves and lines and in patterns on specified area as instructed by Architect / Client, exposed surfaces of veneer shall be finished with approved Polyurethane polish. The cost of necessary hardware's, adhesives, wastages etc.; as required for complete the works. Actual visible surfaces only will be measured and paid. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

4mm thick veneer of approved colour and shade with Basic Cost - Rs.225 /sqft

4mm thick decorative veneer of approved colour and shade with Basic Cost - Rs. 350 /sft

Providing and fixing of Magnetic writing board and Wall panels with lacquered glass of approved colour from Saint Gobain or approved equivalent make., over the partition, paneling or wall surfaces as shown in the Architectural Drawing. The glass should be Premium GRIHA rated, PU lacquered and opaque with low VOC, Uniform coating, humidity proof and high durability. The rate shall be inclusive of necessary fixing with SCG Glassmate ultrafix sealant or approved equivalent make as specified by manufacturer. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

4mm thick Annealed lacquered glass with SGG Planilaque Evolution series or approved equivalent make

6mm thick Annealed lacquered glass with SGG Planilaque Evolution series or approved equivalent make

6mm thick Toughened lacquered glass or approved equivalent make as per manufacturers specification.

6mm thick Annealed lacquered glass with SGG Planilaque Metallic and Pastel series

Supply and installation of acoustic wall panels to a recycled PET/ Wood wool / Polyester fabric, fixed over the existing partitions / walls with adhesives. Spacing between the panels to be as per manufacturer's specification. Rate shall be inclusive of adhesives, brackets, wastages, all accessories and scaffolding at all heights. Rate to include wall mounting hardware with peripheral edge trim - Aluminum Anodised U or T shaped 6mm profile etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Price - Rs 300/ Sft.

6mm thk

12mm thk

Specification same as above but with printed designer or 3D panels. Basic Cost: Rs 450 / Sft

Supply and fixing of 6 mm thick Acrylic solid surface Band with or without pen tray niche, over 6mm thick exterior grade BWR Ply backing. All the exposed surface to be covered with acrylic solid surface as shown in the drawing. The exposed edges and corners shall be chamfered to a width of 1mm to avoid sharp edges. Rate shall be inclusive of 6mm solid surface, necessary accessories, sealant for joint finish, adhesives for fixing, buffing/ polishing., complete., Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". (BWR ply measured under relavent item). Basic Cost of Acrylic solid surface - Rs 450 /Sft

Specification same as above but 12mm thk Acrylic solid surface Band Basic Cost - Rs 750 /Sft

Providing and fixing Pinup soft board of as shown in the Architectural Drawing., with 12mm thick soft board panels wrapped with fabric of approved shade. The board shall be fixed on prepared surface with necessary hardware fittings etc. complete. All around the soft board shall be covered with approved 12X12mm Aluminium anodised trims. Rate quoted shall be for the complete finished work, including all the materials and labour mentioned for complete installed work. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: Fabric - Rs 80 / Sft, Aluminium anodised trim: Rs 120/ Rmt

Providing and applying Oil based primer finish to walls as the base for Vinyl Wall Paper/ Graphics. Existing wall /gypsum / MDF board surfaces to be prepare by scraping away any loose particles, dust, etc by washing and scrubbing and 2 coats of oil based primer applied. The wall surfaces are then smoothened using chalk putty as directed. Surfaces are then sandpapered to achieve a smooth finish and made ready to receive wallpaper / graphics as directed. Rate should be inclusive of applying Protection/Masking for fixtures & joineries., nearby. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Designing, supplying and fixing of Digitally reproduced Scotch print decorative 3M graphics wall paper (with controltac & comply feature for direct, bubble-free application on walls) as per the theme selected by clients with UV protective matte over laminate. Customized imagery. The rate shall be inclusive of necessary designing, colour printouts for approval, mockup as required by Engineer-in-charge/Architects/PM/Clients, material, Hardware for fixing, charges etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Price : Rs 2500 / Sqm

Spcification same as above but providing 3D graphic instead of normal graphic. Basic cost 13000/sqm

Providing and fixing of imported wall paper of approved design, fixing detail as manufacturer standrad. Basic cost of the wall paper is 1100/sqm

Providing and fixing of Niche for TV with 16mm thick Ply board to the existing Aluminium partition and finished 4 mm thick prelam board as per detail drawing. Depth shall be maximum 300mm. Rate to include 16mm thk Ply board, Adhesives, screws and wastages complete., Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Height and width of the niche will be measured and paid.

Supply and Installation of 122mm thick Two hours fire rated GI stud partition which includes two layer of tapered edge 12.5mm thick Fire rated gypsum board (conforming to IS 2095 Part 1 : 2011 ) of density not less than 750 kgs /m3 fixed with 70mm GI acoustic studs on both sides. All drywall partitions should have the duty ratings as specified under BS 5234 part 2. The detail specifications and methodology are listed below. Floor and ceiling channel of 72mm width and 0.5mm thick have equal flanges of 32mm made of GI steel to be anchored to the floor and true ceiling using HILTI HLC8x40 / HILTI X - GN20MX anchor fasteners at 600mm c/c in zigzag manner. Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. The gaps between floor / flooring channel, ceiling / ceiling channel should be covered with fire sealant. Acoustic C stud of 0.5mm thick having one flange of 34mm and another flange of 36mm made of GI Steel to be placed at 610mm Centre to Centre in between 72mm floor and ceiling channel. Stud and floor channel are crimped together with crimping tool. Noggin channel of 70mm width and 0.5mm thick having two flanges of 40mm each has to be provided at the horizontal joints of outer layer boards screw fixed to the studs using metal to metal flat head screws. 50mm thick polyester wadding of density not less than 50 kg/m3 shall be placed in metal framework. Holding clip should be used to hold polyester wadding in its position. The fire line gyp boards are to be fixed with Drywall Screws of 25mm and 50mm at minimum spacing of 300mm at Centre and 150mm at periphery of wall to either side of 70mm stud. The gyp boards to be placed vertically to the framework, with joints staggered to avoid leakage through joints. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing compound confirming to ASTM C 475 and fibre mesh joint tape as per the manufacturer's specifications. Joint finishing to be done for both 1st and 2nd layers of gyp board All the GI channels and sections should be finished with minimum 120 GSM as per IS 277. Coating with AZ150 as per IS 15961 will be added advantage. All dry wall screws should be made of Carbon steel confirming to EN-ISO 7049/50 and finished with Case hardened Grey Phosphating CLASS 48 as per EN 14566. All metal to metal screws should be made of Carbon steel confirming to EN-ISO 7049/50 and finished with minimum Zinc Coating Thickness of 4.14micron etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". "Note: 1. The junction of the partition with masonry and all penetration through the partition has to be treated with fire sealant. 2.Vendor has to submit detail specifications with shop drawing for approval. 3.The supplier / manufacturer should inspect the site to ensure that the executed works are adhered to the specification and should submit a guarantee certificate for required fire and acoustic rating. 4. No Deductions for the horizontal service penetrations. 5. Deductions to be considered for Doors and Windows. 6. Control Joint has to be provided at every 10 Mtr. c/c. along the length of wall. 7. Necessary GI stud backing to be provided for holding the soft board / white board panels."

Rate to include providing GI angle bead at all L-Junctions of partition, Nogging channels at the horizontal joints of each boards, GI stop beads around the door openings, providing necessary GI sections backing / Cutting for switches and sockets, additional wood inserts near the openings, necessary sound deadening membrane to achieve the required acoustics etc., Quoted rate to be inclusive of all the works mentioned above with standard drywall partitions accessories. Actual laid area from floor to true ceiling will be measured and paid.

Providing and fixing of 50mm thick Rock wool of density 48 kgs/m3 wrapped with 40GSM fiber glass tissue in drywall partition with holding clips to make it as acoustic proof. It shall be placed in the Aluminium frame cavity. The contractor must ensure that the wool is either wire-braced or holded with clips to prevent it from ‘lumping down’ over a period of time. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Providing and fixing louver panelling of full height for existing DB by using MDF16mm board and louver shutter laminated with approved shade with necessary hinges etc., Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Wooden Acoustic Wall Panels

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 27% open area), backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2,rear scoring with perf 10mm at 20mm pitch, tongue-groove edge for a seamless look, flame resistant (BS476 part 7) , of size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), installed by using GI Strut framework system.The GI Strut framework system shall include Strut CC25, fully knurled, sectional thickness 0.45mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the wall positioned horizontally or vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC25 with the help of fasteners at every 400mm centers Anutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. The system is backlined with Anutone SynthPF 5x25 adhered on wall with dab spots of Anutone stick S7 adhesive. Technical Parameters Fire (Class) – BS476 part 7 , Acoustics – NRC 0.75, Thermal conductivity (W/mk)– na, Climate (°C, RH) – 50, 70, Light reflectance (%) – 75 (Maple Arce),Green (VOC, RC %) – E1, 25 etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

SINGLE GLAZED TOUGHENED GLASS PARTITIONS - WITH ALTERRRALITE SYSTEM-45 FRAME PROFILES

Supply and Fixing of Slim Glass partition of 10mm Toughened Glass using Dormakaba Aterra liteSystem-45 Frames to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using Dormakaba Aterra lite BP45 Profiles at Top & Bottom & Aterra lite SP45 at sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. Dormakaba Aterra lite H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel Alterralite MP45 & BP45 Overpanel Profile to be used.In case of Open glass edges EP45 End Profile to be used.

The Aterra lite profiles shall be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. Approved Manufacturer: Profiles/Frames: Dormakaba, Glass : Saint Giobain/Asahi, Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Designing, Printing, Supply and Fixing of Frost film to glass partitions using 3M frosted film stickers as per required pattern and shape and as directed. Cost inclusive of designing, mockup and installation with all accessories. The vendor must submit required warranty certificates from the manufacturer. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost : Rs 1450 / Sqm

Supply & Installation of 300mm wide Technical Power portal using Double Glazed X-Series partition systems of 105 x 25mm thk section using JEB 1004A as Horizontals at top & Horizontals at bottom and JEB 859 verticals with solid partition from FFL upto 2800mm Complete in all respect considering two layer of using ACP Sheet panel with 9mm Ply Backing with Rock wool & RP Tissue etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and Installation of CNC cut designer board with the materials as listed below. The designer board to be fixed with necessary aluminum supports / suspended hangers, wires etc. Area of the perforated screen will be measured and paid. Design to be approved by Architects. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

With 12mm thick Acrylic solid surface of approved shade. Basic Cost: Rs 650 / Sft

With 20mm thick acoustic panels of approved shade and texture. Basic cost Rs 450 /Sft

With 12mm thick acoustic panels of approved shade and texture. Basic cost Rs 250 /Sft

With 24mm thick acoustic panels of approved shade and texture. Basic cost Rs 500 /Sft

Fabricating, supplying and installing of 3mm thick Sintered porcelain slab- PDS Grigia of STONELAM make with factory embeded fibre mesh backing. Sintered porcelain slabs to have 25years warranty against natural degradation. Standard panel size to be 1mtr x 3mtr and will be cut to size as per architectural intent/ approved drawings. Installation system Designed to withstand wind pressure of Kpa. The porcelain stoneware cladding panels are structurally glazed to aluminium frame work with structural sealant of approved make and VHB tape. the glazed panels will be fixed to the aluminium grid work using suitable brackets as indicated in the tender drawings, the aluminium grid work is fixed to the dead wall. beam, column etc. with MS hot dip galvanised brackets at intervals as per structural requirement, the vertical and horizontal grooves will be sealed with weather sealant of approved make as indicated in the tender drawings. All exposed aluminium surface to be with PPC finish matching to the colour of porcelain stoneware, All aluminium to be anodized finish. Rate to include all expenses including wastage/labour/supply and installation as per technical specification and approved shop drawings. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Cost: 450 / Sq.ft

Supply & Fixing of Fully Glazed Firerated Glass Partition using Two hours fire rated fully glazed Fixed Partition frame (including necessary accessories / packing) & SGG Contraflam Doorlite 11mm (EW 120)

False Ceiling Works

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, Including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification etc., Including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed. but excluding the cost of painting with etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

12.5 mm thick tapered edge gypsum moisture resistant board - Any shape

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/ mK.

"Supply and Installation of Acoustic Mineral Fiber Grid Ceiling tiles with 0.7 NRC with T Grid Sections. The grid sections should be inter locking metal grid of hot dipped galvanised steel regular T grid sections (galvanized @ 90 gsm/sqm) consisting of Main ""Tee"", size 3600 x 38 x 0.30 mm made from 0.30 mm thick (minimum) sheet spaced at 1200mm center to center and Cross ""Tee"", size1200 x 38 x 0.30 mm made of 0.30 mm thick (minimum) sheet to be interlocked between the main T runners at the distance of 600mm center to center to create 1200x600mm module. Cross ""Tee"", size 600 x 38 x 0.30 mm made of 0.30 mm thick (minimum) " sheet to be interlocked at middle of the 1200x600mm module to form grids of 600x600mm to lay ceiling tiles. The perimeter trims to be of 22W x 19H x 3000L mm. Main "Tees" to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6mm dia and 50mm long anchor fasteners, 4.00mm GI adjustable rods with galvanized level clips spaced at 1200mm center to center along the Main Tee. The 4.00mm GI rods should be in accordance to IS 280:2006 and should have a zinc coating of not less than 90 gsm in accordance with IS 4826:1986 and a tensile strength of 300-550 MPa in accordance to IS 1608:2005. The first suspension from the perimeter trim should not exceed 300mm. The bottom exposed width of 15 mm of all T-sections shall be pre-painted with polyester paint. "Installation of Mineral Fiber Ceiling Tiles with square edges, 15 mm thick of size 600 x 600 mm with the criteria as listed below. The mineral fiber ceiling tile shall be firmly bonded wet-felt mineral wool tiles ,primed on both sides and appropriately finished on the visible side in white color similar to RAL 9010. The tiles are asbestos and formaldehyde free. The system must comply with Green building norms. NRC -0.7 as per ASTM C 423 Light reflectance - 85% min Humidity resistance - upto 95% RH Sound absorption - αw = 0.9 as per EN ISO 11654(3rd party certificate mandatory) Sound attenuation - Dn,f,w= 38 dB as per EN ISO 10848"

The rate quoted for false ceiling system shall include scaffolding arrangement at all levels and heights, providing necessary cut-outs for all fixing light fixtures (all sizes) AC diffuser, AC dampers, AC linear grills, smoke detectors, speakers, etc. and any other openings to be made in false ceiling as directed by the "Engineer-in-charge". Mode of Measurement :Deductions in measurements will be calculated on full tile basis where light fittings & diffusers are installed instead of ceiling tiles. (No detection for sprinkler, fire detector, smoke sensor and other small ceiling mounted equipment) etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and Installation of Aluminium Perforated metal ceiling System of approved make., consisting of 600x600mm Lay in tiles of pre coated Aluminium in 0.5 mm thickness in white colour with standard perforation of 2.5mm dia & open area of 16% and Freudenberg Soundtex acoustical fleece glued to the back of the tile to be laid on grid systems with 15mm wide T - section flanges having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. The T Sections have a Galvanizing of 120 grams per M2 & passed through 500 hrs of Salt test. The grid to be formed using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 3mm dia G.I. wire hanger securely fixed to soffit if RCC slab. GI hanger to be placed every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm C/C (max) to form a grid of 1200mmx600mm. 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mm x 600mm,The tiles should have Humidity Resistance (RH) of 100%, NRC of 0.70, Fire Performance A2-s1.d0 in module size of 600 X 600 mm, suitable for Green Building application, with Recycled content of 50%. The Tile & Grid system used together should carry a 15 year warrantee.

The rate quoted for false ceiling system shall include scaffolding arrangement at all levels and heights, providing necessary cut-outs for all fixing light fixtures (all sizes) AC diffuser, AC dampers, AC linear grills, smoke detectors, speakers, etc. and any other openings to be made in false ceiling as directed by the PMC/Architect. Mode of Measurement :Deductions in measurements will be calculated on full tile basis where light fittings & diffusers are installed instead of ceiling tiles. (No detection for sprinkler, fire detector, smoke sensor and other small ceiling mounted equipment) etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and Installation of Aluminium open decorative linear ceiling suspension system of Fame line or approved Equivalent make, with wood finish from approved make as shown in the Architectural Drawing. The size of the panel shall be 25 X 100 mm made of 0.5mm thk Aluminium U profiles. The suspended system shall be supported by necessary hangers, carriers made of 0.5mm thk galvanised steel. The suspended supports are fixed at a distance as recommended by manufacturer. The carriers are then fixed to the suspended supports, the panels are then fixed to the carrier with easy clip in method. The system should posses easy removing and refixing method for checking and maintenance purposes.

The rate quoted for false ceiling system shall include scaffolding arrangement, providing necessary cut-outs for all fixing light fixtures (all sizes) AC diffuser, AC dampers, AC linear grills, smoke detectors, speakers, etc. and any other openings to be made in false ceiling, Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Acoustic False Ceiling

Supply and Installation of Subtex Ebony square edge Glass fibre core fully encapsulated ceiling tiles of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 Ebony grid system.The T15 Ebony Grid system of 600x1200mm module shall include wall angle (WA15B30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15B36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15B12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut slots in the Main T15 at 600mm centers in the direction perpendicular to the MainT15. . Subtex Ebony square edge of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind subtex panels are oriented in one direction to achieve uniform shade. Technical Parameters Core - Glassfibre, Fire – Class 1 & P, Acoustics – NRC 0.9, Climate (OC RH) – 40, 95, Termite resistance – Yes, Light reflectance – Low , Green (RC %) – 35, Hygiene (VoC, Clean room) – Low, Class 3, Strength, Load capacity (Kg) - Antisag etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and Installation of custom designed metal baffle ceiling with Spacing – Random Spacing as per Design as shown in the drawing with specifications listed below Supply and Installation of Baffle ceilings with Architect approved Wood Finish of 100mm(Height) x 40mm/ 50mm/ 100mm / 150mm (Mixed Size Base) x 1.2mm thick extruded Aluminium suspended at a center to center distance of 150 mm to the baffle C Carrier. The baffle is connected the Baffle Carrier with a bolt/nut/Spring washer arrangement as per typical detail attached. The baffle C Carrier is suspended at every 1m in general and at 150mm from Baffle Joints. The baffles come at a maximum size upto 4.3m in length. The baffle end with an End Cap made in Aluminium and is with same finish as the baffle panel. Baffle spacing and fixing arrangement is to be done as per architect’s design and approval. The rate quoted for false ceiling system shall include scaffolding arrangement, providing necessary cut-outs for all fixing light fixtures (all sizes) AC diffuser, AC dampers, AC linear grills, smoke detectors, speakers etc and any other openings to be made in false ceiling as directed etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

40mm base

50mm base

100mm base

150mm base

Supply and Installation of Custom Design Baffle ceiling consists of 25x50mm extruded aluminium box section profile with extruded end connector at both ends and a hexagon shaped Extruded aluminium column with six notches along the circumference. The hexagon shaped column is positioned as per size of the equilateral triangle approved and suspended to the true ceilings using 8mm threaded rod and a carrier. The 25x50mm extruded aluminium box sections are cut to required approved size and special extruded end connector is fixed at both the ends of the cut baffles. Each of this box section is then inserted on to the six sides of the column and thereby forming a hexagonal shape as per the drawing. the box sections, columns and end connector are powder coated in solid colour/wood finish to required shade specified by the architect. The entire system consists of all aluminium extruded profile and when so installed form a rigid ceiling detail. Suspension by M6/M8 threaded rods anchored to the ceiling and connected to the extruded aluminium columns at every junction. Hexagon Caps in White colour are fixed at the bottom of the extruded columns to complete the ceilings etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Providing and fixing Wooden false ceiling as shown in the Architectural Drawing using 50mmx25mm Aluminium extrusions in both ways not more than 600mm c/c with necessary supports from ceiling and all the exposed surfaces should be covered with one layer of 11mm thick MDF board. Rate inclusive of necessary countersunk heavy duty screws, 11mm thick MDF board, hardware and adhesives. Teakwood edge beadings / Aluminium edge profiles to be provided at all levels and heights and as directed by Engineer- in- Charge. The finish are listed below. Rate to include any shape and size as per drawing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

All the exposed surfaces to be finished with 4mm thick Veneer of approved shade with PU finish. Rate inclusive of Veneer, Adhesives for fixing and PU polish Basic Cost: Rs 230/ Sft

All the exposed surfaces to be finished with 1mm thick Laminate of approved shade . Rate inclusive of laminate, PVC edge beadings and adhesives Basic Cost: Rs 75 / Sft

Supply and Installation of Senses Acoustic suspended cloud Ceilings with extra coating for stain resistant as shown in the Architectural Drawing, from Senses Akustik suspended vertically with thickness not less than 35mm of approved colours to be hanged to the ceiling/ soffits etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". content : 100% wool felt, flexy ply dimensions : 400mm dia - 1200mm dia thickness :35mm thickness/dimension tolerance : +10% , -10% Hanging system: hardwares / clutch wire environmental 100% wool felt contains no formaldehyde, biodegradable,voc free, no chemical irritants, recyclable and free of harmful substances.acoustics : NRC - 0.85 Environmental - CII greenpro certified product, type 1colour fastness to light :- class 4-5 (40 hours ) .acoustics : nrc - 0.85 environmental - cii greenpro certified product, type 1colour fastness to light :- class 4-5 (40 hours ) .

Hexagon of Sides 600mm with approved colour Circular type

450mm dia

900mm dia

1200mm dia

Supply and Installation of Acoustic suspended Baffle Ceilings as shown in the Architectural Drawing, from Senses Akoutik or approved equivalent make, suspended vertically with thickness not less than 20mm of approved colours to be hanged to the ceiling/ soffits. Baffles should be made up of Recycled PET or felt. The length of each baffle to be as per drawings and the spacing as per manufacturers specification or as directed etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Must comply with the following criteria Sound absorption Test according to EN ISO 354 Sound absorption co efficient according to EN ISO 11654 NRC ratings according to ASTM C 423 Certificate for indoor climate labeling Basic rate : Rs 275 / Sft The rate quoted for baffle ceiling system shall include necessary cables, hangers, clips, anchor bolts, connecting clips and other accessories for hanging, scaffolding arrangement, wastages etc, Working at all levels and heights and as directed by Engineer- in- Charge. The length and height of the baffles will be measured and paid.

Providing and Fixing of Click-Trap Access Panel of approved make., with unique locking system in ceiling. In general, exterior and interior framework made of stable Aluminium profile placed at bottom of the Gypsum ceiling level and shall be fixed using suitable metal drywall screws with nylon plugs etc complete. The access panel to have a 12mm thk fiber cement board door to receive paint (low VOC) or laminate finish & entire perimeter equipped with hard wearing insulating/ sealant tape and should be fixed in line with the nearby false ceiling. The rate shall be inclusive of all necessary accessories, hardware's like snap lock with spring loaded bolt of galvanised steel body, gypsum board with approved paint finish, laminate of approved shade, safety steel wire 1mm thk to prevents the door from falling, wastage etc, as required ,transport charges, handling, loading and unloading, Installation etc. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Size 300mm x 300mm

Size 450mm x 450mm

Size 600mm x 600mm

Size 1200mm x 600mm

Providing and fixing of Axiom Perimeter trim of Armstrong or approved equivalent make with 150mm wide all around the suspended metal ceiling areas. The trims to be finished with factory made polyester paint of 50 microns minimum. Rate inclusive of all accessories like hangers, corner trims, splice plates, T bar connection clips for complete installation for the system including all accessories etc. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Miscellaneous Works Expansion Joints

Supply & Apply of " INTECH" make surface-mounted metal floor cover is designed for interior, new or retrofit applications requiring movements up to 100%. The selfcentering aluminum cover plate allows for thermal movement and seismic movement. with EPDM moisture barrier. • Extrusion: INS FF 100 model is extruded with 6063-T5, ASTM B221 • Sheet – 6061-T6, 3003-H14, 5005-H34, ASTM B209 surfaces to be placed in contact with Floor-to-Floor / Floor to Wall expansion Joint- 100mm joint width. 1. Type: Cover plate. 2. Cover Plate Design: Plain 3. Attachment Method: Mechanical anchors. 4. Load Capacity: Standard Duty 5. Moisture Barrier: EPDM Sheet.

Supply & Apply of " INTECH" make surface-mounted metal floor cover is designed for interior, new or retrofit applications requiring movements up to 100%. The selfcentering aluminum cover plate allows for thermal movement and seismic movement. with EPDM moisture barrier. • Extrusion: INS FF 150 model is extruded with 6063-T5, ASTM B221 • Sheet – 6061-T6, 3003-H14, 5005-H34, ASTM B209 surfaces to be placed in contact with Floor-to-Floor / Floor to Wall expansion Joint- 150mm joint width. 1. Type: Cover plate. 2. Cover Plate Design: Plain 3. Attachment Method: Mechanical anchors. 4. Load Capacity: Standard Duty (500lbs) 5. Moisture Barrier: EPDM Sheet.

Supply & Apply of " INTECH" make surface-mounted metal floor cover is designed for interior, new or retrofit applications requiring movements up to 100%. The selfcentering aluminum cover plate allows for thermal movement and seismic movement. with EPDM moisture barrier. • Extrusion: INS FF 200 model is extruded with 6063-T5, ASTM B221 • Sheet – 6061-T6, 3003-H14, 5005-H34, ASTM B209 surfaces to be placed in contact with Floor-to-Floor / Floor to Wall expansion Joint- 200mm joint width. 1. Type: Cover plate. 2. Cover Plate Design: Plain 3. Attachment Method: Mechanical anchors. 4. Load Capacity: Standard Duty 5. Moisture Barrier: EPDM Sheet.

Supply & Apply of " INTECH" make surface-mounted metal floor cover is designed for interior, new or retrofit applications requiring movements up to 100%. The selfcentering aluminum cover plate allows for thermal movement and seismic movement. with EPDM moisture barrier. • Extrusion: INS FF 300 model is extruded with 6063-T5, ASTM B221 • Sheet – 6061-T6, 3003-H14, 5005-H34, ASTM B209 surfaces to be placed in contact with Floor-to-Floor / Floor to Wall expansion Joint- 300mm joint width. 1. Type: Cover plate. 2. Cover Plate Design: Plain 3. Attachment Method: Mechanical anchors. 4. Load Capacity: Standard Duty 5. Moisture Barrier: EPDM Sheet.

Providing and fixing of 50mmx50mm size Column Corner Guard of approved make for vertical corner's of RCC columns, Brick pillars, Brick walls, Partitions, using sub frame of 1.5mm thick aluminium profile fixed in to the above corner surfaces by using anchor fasteners. Then the top covering with Rigid PVC panel profile is to be fixed on the sub frame by interlocking. The rate shall be inclusive of necessary hardware's etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and installation of Transition trims for walls at the junction of the glass / writing board / soft board / Wall paper as per detail drawing. The shape of trim shall be "U", "J", "T" or as per samples approved. Rate inclusive of cutting, necessary wastages and sealant/ adhesives for bonding. Sample to be submitted and approved before procuring. Finishing of trim as per drawing / Architect's approval etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Aluminium anodised "T" shaped 5mm X 14mm (PCP135)

Aluminium anodised "U" shaped 5mm X 14mm

Aluminium anodised "L" shaped 5mm X 12.5mm (PFP124)

Providing and fixing floor transition profiles for floors of approved make with sample section for the junction of tiles/ granite / Italian marble flooring / carpet to accommodate level variation. The top profile should be of approved shade. The base shall be screwed neatly to the flooring with SS screws and the top profile to be fixed as per manufacturers methodology. Finishing of trim as per drawing / Architect's approval etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Minimum 20mm wide Aluminium anodised profiles - Basic Price Rs.1100/ rmt

Aluminium stair nosing - 24mmx9mm (SNP091)

Providing and fixing of Barrier mat for DUST–BUSTER RECESS-ALUMINIUM MATTING (OPTIONS-GREY CARPET, BROWN CARPET) Model no 5014 from Euronics or Equivalent etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Providing and fixing Pelmet made to shape and sizes as given in below, but in general it shall be made out of 18mm prelaminated MDF finished with white laminate or approved colour as directed. The rate shall be inclusive of necessary accessories like hangers rods/ Hilti anchor fasteners, sunken screws, all factory finished etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Basic Price : Rs 45 / Sft

Size of the pelmet shall be 200 X 200mm

Providing and Fixing of Roller Blind should have sturdy aluminium top tube of 38mm diameter, powder coated bottom bar, with suitable roller clutch mechanism and plastic ball chain. The Roller Blind fabric should possess the below mentioned specifications etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

a) Openness factor - 5% b) Composition –35% fiberglass and 64% vinyl on polyester c) Core yarn should be Fiberglass d) Fabric thickness –0.43mm e) UV blockage – 95% f) MIF seal of approval g) Lead-free certified – RoHS compliant h) Flame Retardant – NFPA 701 and California US title 19 i) Anti-fungal / Anti-bacterial for lifetime – MICROBAN®product protection j) Environmental certification – GREENGUARD Gold certified k) Warranty – 10 years l) Approved make – Phifer

Supplying and fixing the 5mm groove profile to differentitate the laminated sheet colours at wooden partition wall.The rate including supplying,cutting,grouve cutting pasting and fixing etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Supply and Fixing Mirror as per drawing, in general 6mm thick mirror with aluminium frame at 600 mm c/c both ways for backing frame fixing with 12MM thick BWR ply and fixing with stainless steel studs. Rate quoted shall be for the complete item including all the materials and labour mentioned above. Rate to including all materials, labour changes, transportation, lead & Lifts, wastage etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect".

Design, Supplying and Fixing of various signages are described below. The Colour, Font and Size should be approved by the Clients. Vendor to submit the samples required by Client for review and approval. The quoted rate shall be inclusive of required suitable fixing accessories and double sided adhesive tapes of 3M make or equivalent etc., Complete complying with standard specifications and as directed by the "Engineer-in-charge/Architect". Note: Please note that the proposal given are only for vinyl stickering with ACP / Acrylic base in consideration. However, should there be a requirement from the client end on the material finishes of the base, such as SS base / embossed and Size of the signboards, according to corporate identity there will be a variation in cost.

Name and Numbers Size: 12” x 3”, SS brush finish to be fixed double side 3M tape and with provision for slide on.

Work Station signs: Size: 3" x 1.5". WS numbers Printed in Vinyl sticker.

HUB room signage with Entry Restirctions Size: 12” x 4”, Foam Base vinyl sticker in colour as per design mounted on door with SS screws/ double side tape.

Toilet sign: Size: 6” x 9”, Fabricated in Silver ACP Base with vinyl sticker with the Gents/Ladies pictograph

Direction signs: Size: 12” x 4”, With clear Acrylic base Single sides sign of approved colour and Green base signs with electrical illumination with battery backup, to be hung by SS chain :

PUSH, PULL Signage: Size 1.25" x 5", Brushed Stainless Steel Plate with the font embossed for all cabin doors

Supply and Fixing of signage at entrance. Signage to be made of SS Plate with acid itch letter fixed with SS studs in main entrance. Size - 56" x 16" with necessary concealed fixtures.

Supply, fabrication and installation of Logo at Reception based on the design intend. Cost to include for complete supply and installation including the light fixtures as per intend.

Providing and fixing of Chair rail with 1mm thick Laminate Band as shown in the drawing, to the existing partition to a height of 250mm with 12mm thick BWR ply backing finished with laminate of approved shade as mentioned below. Quoted rate should be inclusive of 12mm thk ply, cost of laminate, wastages, necessary screws and adhesives. Basic cost of Laminate - Rs 50 / Sft