Directorate Of Town Panchayats Tender

Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30

Grade beam and footing

Plane Surfaces such as RCC slabs, lintel, beam, waist slab etc.,

Plane surfaces for square column

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

Up to Basement

Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in CM 1:3 (one cement & Three Crushed Stone Sand (M- Sand) using ground moulded chamber bricks of size 9"X4 3/8"X 2 3/4" standard specification including finishing, curing, etc., complete complying with standard specification - 100cft

Up to Basement

Ground floor

Collection supply and filling of well gravel filling approved quarry including cost and Conveyance of all materials to site and all labour charges for filling etc., Complete.

Plastering with CM 1:5 (One part of cement & five parts of sand) mix for 12mm thick including cost and conveyance of all materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:56&57

Special Ceiling Plastering with CM 1:3 (One part of cement & three parts of sand)mix for 10mm thick including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:30,56&57

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Painting two coats of newly plastered wall surface with ready mixed Cement paint of first quality and of approved colour over a priming coat including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and laying in flooring with fully polished Sinthetic Grey colour Granite stone of 10mm thick (average) of 2' X 1' in size laid in cement mortar 1:2 (one cement and two Plastering sand) 20mm thick & pointed with same colour of cement etc., complete as per standard specification

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supplying , fabricating and fixing in position of aluminium anodized natural colour matt finish with Half prelaminated particle board and Half glazed door using 5.50m thick plain glass .The door frameshall be anodised ajuminium box section of size 101.6x44.45x3.18mm at 2.319 Kg/m. The shutter frame shall be of aluminium anodised box type section of size 50X 44.45X 2.5mm @ 1.202 Kg/m for vertical styles and top rails. The Lock rails shall be using box type section of size 50X 44.45X 2.5mm @ 1.292 Kg/m and bottom rail shall bebox type section 100.40X 44.45X 2.5mm @ 1.974 Kg/m. The rate shall include the provision for necessary accessories such as pivot - 1No. aluminium clips, rubber beading ,PVC felt, locking arrangements, furniture fittings such as aluminium tower bolts - 250X12mm - 1No., aluminium tower bolt 200X12mm - 1No aluminium door stopper with rubber bush - 1No., 200mm long D type handle for both sides -2No., lock - 1No., Hydraulic Door closer of approved quality using aluminium extruded section body tubular type with double speed adjustment with ISI monogram - 1No. including cost of all materials, labour charges and power consumption charges

required for fabrication including chipping, dis making holes to the extent in RCC column / beam / masonry with power drill wherever necessary and redoing thedamaged portion to the original condition after fixing etc., complete. The bottom portion of shutter shall be panelled with 12mm thick best quality bith sides prelaminated. The top portion of the shutter shall be panelledwith 5.5mm thick plain glass and rubber beading for the half portion fixed in position with rubber beading and aluminium glazing clip of size 17.15 X 17.27 X 1.5 @ 0.176 Kg/m is using for fixing glass and prelaminated board with shutter. All aluminium sections are to be anodised with matt finish under electrically controlled condition in accordance with ISI specifications per IS 1868/1962 for anodic film thickness of not less than 15 microns. All aluminium sections, 5.5mm thick plain glass and 12mm thick prelaminated board on both sides shall be got approved by the Executive Engineer before use on the work - Single Leaf.

Supplying and fixing 30mm thick solid core PVC Door shutter with PVC frame of size 50x45mm with suitable rebate for housing the shutter (Confirming to IS 4020 with updated amendments) consisting of frame made out of MS tubes 19 gauge thickness etc., complete

Supplying, fabricating and fixing in position of Aluminium anodized natural colour matt finish Sliding Window arrangements and shutter arrangements so as to drain the water entering and made with extruded aluminium section of following sizes with necessary accessories such as rubber beadings, best quality rubber lock, handle and fixing 4mm thick plain/frosted glass including cost of all materials etc., complete.Supplying Fabricating and Fixing in position Aluminium Sliding window.Two Track Frame Bottom ghutter section 62x37x1.50mm @ 1.218 kg/m side and top frame 62x31.50x1.50mm @ 0.778 kg/m shutter: top & bottom section- 40x18x1.50mm at 0.38 kg/m vertical section-40x18x1.50mm at 0.493 kg/m inter locking vertical section 40x28x1.50mm at 0.632 kg/m.

Fabrication supply and fixing in position of Aluminium natural colour matt finish Louvered Ventilator in all floors made with extruded aluminium section of following size with necessary accessories such as rubber beading, best quality of handle, lock including supplying and fixing of 4 mm thick plain glass including cost of all materials, labour power consumption required for fabrication drilling holes in RCC column / floor slab / masonry wall wherever necessary with power drills to the required extent and making good to the original condition after fixing etc., and as directed by the departmental officers etc., complete. The aluminium frames to be anodised under electrically controlled condition in accordance with ISI 1868 / 1962 specification for an average anodic film thickness of not less 15 microns and all the materials should be got approved by the Executive Engineer before use on work.

Outer frame alround section of size 62x38x2mm @ 1.174 kg/ m vertical louvered section of size 60x30x4mm @ 1.27 kg/m and aluminium clips of size 19.05x10.27/11.05x1.20mm @ 0.169 kg/m.Toilet V

Supplying and fixing of M.S.Grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of red oxide primer etc., complete.

Painting with two coats of Approved colour of best quality synthetic enamel paint, painting over new iron work including cost and conveyance of all materials and all labour charges etc. complete as per Standard specification and as directed by the departmental officers. (New Iron Surface).TNBP No:66&66-A

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 10.00 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TWswitch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wireconnection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVCplug point.SD 37

Supply and run of 2x 4 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class ‘B’) suitably bent at both ends with necessary angle iron upright and end supports for mains(PWD standard data No.SD. 69).

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories,With TW switch Box 5A FT Switch Flush with wall 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC cooncealed LIGHT /FAN point SD 25

Supply and fixing of single box type 4'40 W Fluorescent fitting complete with copper choke and condenser conduit pipe suspension ceilingwith PVC unsheathed copper lead to fitting with tube SD 89

SupplyandfixingofTNEBmeterboardsuitablefor32Athreephaseserviceconnectionwith3Nos.32Afuseunit(500V)32Aneutrallinkandearthlink(1"x1/8"copperflat)onTWplankofsize600mmx450mmx19mmwithsupportingTWreepersof1"thickaneithersidewithpaintingwithsuitableboltandnutsforfixingtheTWplankonwallwithearthconnectionandinterconnectionwith7/20PVCinsulatedcopperwirefromEBmeter to fuse unit SD 129

Supplyandfixingof1200mm(56")ACceilingfancompletewithsteppedelectronic300Wregulatorwith300mm down rod on the existing clamp SD 111

Supply and fixing of 80W LED Focus Light Fitting with LED TWAD SOR PAGE NO.206

Supply and fixing of Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms (SOR PG 153)

supply and fixing of 7.5 KVA UPS (Single Phase In & Single Phase Out) CAPACITY - SYSTEM WITH BATTERY - 1 HOUR BACK-UP SOR PAGE NO 158

Supply and Fixing of CCTV Camera with Specification of Dahua- HAC-HFW 1100DP-B-0600 720P 1 Mega Pixel Analog High Definition camera, outdoor-25/30 fps@720P,1/2.9" 1 Megapixel CMOS, 50m IR,ICR, 6mm Lens optional, IR Bullet Dahua - Channel - AHD, High Video Quality on HD 1080N, Transmit Video Signal, audio signal & Dual way data communication signal over one coaxial cable, HD Video transmission without Video quality loss & delay, extremely, long transmission distance (300), as directed by Departmental Executive Engineer.(PWD SOR-Pg no-21,Sl No-14)