Urban Improvement Trust Tender

Lalri /Anermi /Golden Duranta

Crape Myrtal /Hemelia /Lantana Selloviana /Lantana Yellow /Rukmani /Gaudichaudi

Jade Plant /Aclypha Tricolor /Kaner Dwarf /Copper Plant /Gudhal /Chandni/ Kamini Muraya /Callindra Pink Off.

Pedilanthus /Laila Majnu

nwc dk la/kkj.k dk;Z – yxh gqbZ nwc dk la/kkj.k dk;Z esa [kjirokj fudkyuk] fu;fer flapkbZ djuk] [kkn Mkyuk ,oa e’khu ds zkjk fu;fer dVkbZ djuk rkfd nwc vPNh rjg ls fodflr gks ldsA

Maintenance of Hedge, Climbers, Shrubs at parks including watering, trimming, preparation of thawala, manure and complete work.

Providing and supplying of Garden bench (Victorian) at site both side of garden bench is made of cast iron having back height of 720 mm and seating height of 390 mm (approx.) it may vary at some places and both side of Garden bench is connected with 10 Nos. MS tube of rectangular section size 65×25×3mm having length of 1520 mm for seating purpose with extra support 25×5 mm MS flat for extra stability. All sharp and rough edges of bench is to be grinded with grinder and all fill up with m- seal, and fixed at required position and this bench is having the provision of hold & fast system weight not less than 95Kg (for grouting) bench is complete with a coat of 1st class red oxide and with three coats of synthetic enamel of 1st class quality paint in green colour finally bench is assembled with nuts and fixing at the site complete with the direction of E-I-C.

Laying of lawns including ploughing leveling breaking of clods manuring and removal of stones etc. (cost of manure or extra good earth to be paid separately )maintenance of lawn foe 30 days or more till the grass forms a thick lawns free from weeds and fit for moving in the duration of planting if lawn die some where the contractor will replant it at his own cost In rows 15 cm apart in either direction

Sweeping / cleaning of gardens roads lawns paths and disposal of all rubbish

Prunning & trumming and cutting of old big trees on the road side The contractor will deposit the cut wood in the Deptt.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed : All kinds of soil

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Single See Saw : The Single See Saw suitable for 4 to 8 years children and made of MS pipes which should be following specification : Area Required : 1.50 mtr.x 3.0 mtr. Height : 0.90 mtr. Main Pipe : 50 NB pipe Plank : 40 NB pipe Handle : 20 NB pipe Seats : MS sheet (5mm thick) FRP (ISO : 9001-2000 make)

Double Swing : Double Swing is suitable for 4 to 14 years Children and frame is made of NB pipes which should be following specifications : Area : 3.0 mtr x 2.50mtr. Safe play area : 4.0 mtr x 3.50 mtr. Height : 2.40 mtr. (on ground level) Leg support : 40mm NB pipes Top bar : 50mm NB pipe Seat : 9mm thick reinforced rubber (Non skid chequired top, bearing : Housing special casting heavy duty bail bearing, suspension : 7mm dia Electro Galvanized chain (ISO : 9001 2000 make)

Wave Slide : The sliding chute of wave slide is made of 6mm thick fibre glass reinforced plastic. (Binani or equivalent make) with a smooth surface consist of 3 sliding mould of 2.00 ft. (approx). The platform made out of 10 gauge MS sheet and shall be supported on 33mm OD 14 gauge. The ladder shall be 60cm wide (approx) and will be made of 25mm NP pipe with 15mm dual steps. The slide shall be supported on three parallel supports of different length. the size of the slide above the ground level shall be as follows platform height 2.40, slide length 4.20m and slide width 0.50 mtr. (approx)

Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick.

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: New work (Two or more coats applied @ 3.84 kg/10 sqm).

Rough Chisel dressed Sand stone 35 mm thick flooring of approved shade set over 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointing with cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : Mandana stone

Providing & Fixing of anti skid high strength, high finish, coloured Tile/Interlocking flooring having thickness 60 mm over prepared surface with base of 25 mm thick cement and mortar 1:4 as per approved colour, design & drawing including all erspect complete. (the design of paving blocks shall be decided by Engineer-in-charge)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge).

Construction of tube-well from ground level and upto 100 Meter depth and above sizes in all types of soils in alluvium strata by “bailing” method and without gravel packing as per IS: 2800 (Part - I& II) 1979 specifications (The work includes formation of cavity well at bottom by development with appropriate air compressor or bailer pumping and also lowering of casing pipe but excluding cost of the casing pipe. The tube-well should have a throughout bore as per nominal bore of casing pipe. The work would be completed after obtaining sand free water.)

150 mm dia Nominal bore.

Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. 150 mm Nominal bore of pipe

S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 150mm dia

S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.

Installation of submersible motor pump set in Tube-well/open well complete ( labour charges only) including transportation of tripod, chain pulley block & any other material required for lowering purpose.

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated

SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . For single phase Submersible / Monoblock pump 0.5 HP to 1.5 HP (DOL starter)