Department Of Atomic Energy Tender
... More
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Department Of Atomic Energy - DAE Tender
Civil And Construction
Pipe Line Project
Eprocure
Opening Date12 Mar 2025
Closing Date29 Mar 2025
Tender Amount₹ 71,47,382
Costs
EMD
₹ 1,42,948Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_HWB_852808_1Bid Award Id
ViewTender No
HWPK/MECH/2024/432Tender Authority
Department Of Atomic Energy ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Radiography of the weld joint with gamma ray source as per ASME code section III :-For carrying out radiography work, contractor should arrange Gamma ray source of proper capacity. Arrange for punching segment mark on the pipeline nearer the weld joint arrange source and film positioner, taking exposed film and developing it, drying the film and submission to HWPK engineer. Film to be used for this purpose shall be NDT - 65 or its equivalent. They should also cordon the area where radiography is to be taken with necessary caution display board.
3200
-
-
... More
SW/FW/NW type joints of Sch 80
500
-
-
... More
stainless steel to stainless steel piping welding job including pipe cutting, bevel edge preparation and fit up with the use of GTAW process for root, stabilizing & fillup/final passes using pass using ER 316L filler wire. Job also includes Liquid penetrant test of each joint after root and final pass. Preparation of as build isometric drawings & weld inspection report. The 70 to 80 % of total quantity shall be at a height of 5 to 15 meter range. For welding job at height scaffolding/winch system shall be used. Contractor shall arrange all scaffolding material/winch system as per job requirement & guidelines of EIC.
-
-
-
... More
Supply & fabrication, welding and erection of structural steel platforms/sliding supports/support clamps with structural sections/plates/gratings to be fabricated by contractor as per site conditions in guidelines of the HWPK engineer.
3
-
-
... More
Removal of existing installed pipes from their position by gas cutting, grinding m/c etc :-Existing pipeline to be cut and removed by grinding/ gas cutting and shifting of same to designated place/HWPK stores as per guideline of engineer In Charge. all the scaffolding material, material handling equipments like chain pulley blocks, slings, ropes, gas cutting set and grinding machine shall be in contractor scope of work.
5000
-
-
... More
SW/FW/NW type joints of Sch XXS
250
-
-
... More
BW type joints up to Sch. 40S
700
-
-
... More
SW/FW/NW type joints of Sch 40S
250
-
-
... More
Post weld heat treatment of welded joints by resistance heating up to 610 degree centrigrade after radiographic examination. The chart of stress relieving shall be submitted to Engineer In charge. The contractor shall follow the HWPK post weld heat treatment procedure as per guideline of EIC.
2750
-
-
... More
BW type joints up to Sch. XXS
2500
-
-
... More
Weld build up inside tanks, valve bodies and flange areas at various locations as marked by engineers InCharge. The job includes following works :-(1). Cleaning of area with Wire brush/grinder.(3)Root pass and Subsequent pass welding with GTAW process with use of ER 70 S 2 Filler wire. (4). Balance Passes With SMAW process with electrode E 7018-1.(5). Flushing of excess welding to match the adjacent area thickness. (6). Liquid penetrant testing before weld build up, after every pass of weld build up & After weld build up job completion.(7).Preheating of area as per job requirement before start of weld build up.(8) Contractor shall follow the weld build up guidelines of Engineer In charge.
5000
-
-
... More
Carbon steel to carbon steel piping welding job including pipe cutting, bevel edge preparation and fit up with the use of GTAW process for root & stabilizing pass using ER 70 S 2 filler and SMAW process for fill up /final passes using AWS E 7018-1(spl.) electrode. Job also includes Liquid penetrant test of each joint after root and final pass. Preprration of as build isometric drawings and weld inspection report. The ten to fifteen percent of total quantity job shall be at a height of thirty to fifty meter height above the ground. For execution of welding job at height scaffolding/winch system shall be used. Contractor shall arrange all scaffolding material/winch system as per job requirement & guideline of EIC.
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements