Ajmer Development Authority Tender

25.0 Sq. mm

3.5 core

10.0 Sq. mm

4 core

SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and Other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-

(a)Thickness of CRCA sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided

(b)complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side of panel. The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.

[c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only. All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar / Flexible wire for Interconnection between Main busbar and Switchgear is to be Paid Extra )

(d)Wiring between components within switchgear and Incoming / outgoing cable shall be done through the terminal block only. Direct connection shall not be permitted. Each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. For tap-offs, adjacent terminals with shorting strips shall be used. 10% Spare terminal blocks shall be provided. Wire identification on marking strip shall correspond to the designation of the wiring diagrams. All wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.

(e)All wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, Wiring between terminals of various devices shall be ‘point to point’ (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.

(f)Floor mounted panel shall be mounted on Base frame of ISMC channel size 100 x 50 x 5 mm ( to be paid Extra )

(g) Tests: The insulation resistance (with 1000 V Megger) and High voltage Power frequency test (by applying a voltage of 2.5KV for one minute) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. The insulation resistance shall not be less than three megaohm. CT Secondary current injection test shall also be carried out.

(h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI Test certificates to be submitted)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Providing & Fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and AC1 rating of 16-20 amperes including making connection, programming conforming to IEC 60730-1 and 60730-2-7 etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

One day reserve (Analog type )

Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor as per PWD specification for electrical Works, ISI marked IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking, auxilary contacts, Din rail mounting type including making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

4 pole Power contactors with following AC 1 Rating

100 Amp

Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator with standard short circuit withstand capacity , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Electrolytic grade Aluminium bus bar 6010 grade

S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

40 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

2 x 2.5 sq.mm

1 x 4.0 sq.mm

1 x 6.0 sq.mm

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

Single pole MCB (With B/C curve tripping Characteristics)

6 A to 32 A rating

SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

4 pole MCCB With Thermal Magnetic release

125 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

27.54 SITC of Outdoor LED sign board with LOGO on size of min. 24*8 feet including sub component :- ACP sheet of 3 MM thickness, Acrylic sheet of 3 MM rising of 2.5 inches with male and female option . Best quality LED modules with three year warranty having 170 degree viewing angle with 100 LM with complete water and dust proofing . M S angle and iorn framing etc as required

Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

25mm x 3mm Alum. Strip

Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Providing and fixing of IP 65 protected Polycarbonate / Polysterene fuse box moulded with inside knock outs of following size with hinged cover, transparent window, PU gasket, locking arrangement, duly holded with 2 nos. pole clamps of 20 mm x 3 mm flat with nut and bolts, The box shall be provided with Din rail, 4 / 8 way 10.0 / 16.0 sq.mm heavy duty connector, earth terminal, complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

225 mm X 225 mm X 100 mm

Providing and Laying RCC Foundation for Octagonal / Conical Street Light poles, High mast Poles as per Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

A) Excavation of Pit for Foundation Size upto required depth from Ground level

B) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete.

C) Providing and laying in position cement concrete of M-10 grade of 75 mm thickness

D) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing in position and binding all complete.

E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing and Pedestal

F) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.

G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal including Curing the foundation for 7 days.

H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face.

Pole Foundation for Octagonal pole from 7 Mtr. To 9 Mtr.

SITC of Outdoor LED sign board with LOGO on size of min. 24*8 feet including sub component :- ACP sheet of 3 MM thickness, Acrylic sheet of 3 MM rising of 2.5 inches with male and female option . Best quality LED modules with three year warranty having 170 degree viewing angle with 100 LM with complete water and dust proofing . M S angle and iorn framing etc as required

SITC of 9000mm pole with single/double arm of circular mild steel pipe of two section (grade YST 210), Bottom section 139.7mm Dia x 3.6mm thick made of circular mild steel pipe of two section (grade YST 210), Bottom section 139.7mm Dia x 3.6mm thick with 3000mm Height & Top section 114.3mm Dia x 3.2mm thick with 4430mm Height. Decorative base made of Cast Iron (380mm Square x 1127mm Height) with door SITC of 9000mm pole with single/double arm of circular mild steel pipe of two section (grade YST 210), Bottom section 139.7mm Dia x 3.6mm thick with 3SITC of 9000mm height pole made of circular mild steel pipe of two section (grade YST 210), Bottom section 139.7mm Dia x 3.6mm thick with 3000mm Height & Top section 114.3mm Dia x 3.2mm thick with 4430mm Height. Decorative base made of Cast Iron (380mm Square x 1127mm Height) with door 432mm height x 102mm width. Decorative cast aluminium cone (230mm Dia x 150mm Height) coverd on the bottom & top section joint area. Bracket stem made of MS pipe 88.9mm Dia x 2.9mm thick, emerging from a forged ring upto a height 1420mm . 38.1mm x 2mm thick, spruced up with MS Scroll with gravity die cast aluminium leaf and MS floral embellishment, is firmly held to the stem by way of MS clamps and the arm bears cast iron knobs at one end and other end facilitates the fitment of pendant luminaire at 920mm on two side from the vertical axis of the bracket stem. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium inner service door 348mm height x 110mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop-in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 300mm Square x 16mm thick Steel of grade E250 to IS 2062 : 2011 with 4 make phillips,bajaj,surya ,k-lite,luster

SITC of 120W led pendant mounted compact street light. Type IV (Asymmetrical light distribution). Luminaire made of specially spun aluminum body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitable for mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK08 (Polycarbonate diffuser). Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>70. with expected service life of at least 50,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 5KV. e. CE & BIS Certified. Inhouse NABL accredited lab. The fixture shall be provided with Pure polyester powder coated Black & Gold finish as approved by department in-charge.make phillips,bajaj,surya ,k-lite ,luster

SITC of Color Changing RGBW/ RGBA 80W LED Wall Washer/ Linear SITC of Color Changing RGBW/ RGBA 80W LED Wall Washer/ Linear Lumianire surface mounted Narrow/Medium/ elliptical beam wall washer 1000mm luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics. With thick toughened glass, clear/powder coated. Luminaires are with serviceable DMX 512 Decoder inbuilt with Independent DMX Control Master Slave function ability of Mode Selection, Addressing, Intensity setting and also able to operate with Universal DMX 512 Master Controller. Controller can achieve 16.7M colors. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of Extruded Aluminium adjustable Brackets made of Stainless Steel . Impact resistance level should be suitable to site condition minimum IK06. Adequate heat sink with proper thermal management shall be provided. Luminaire should be provided with suitable integral/separate non-integral power supply unit. Fixture shall have Input Voltage 24Vdc and external driver should operate @ 120- 277 VAC, 50/60Hz, THD<15% and PF>0.9. Operating Temperature : -10°C to +45°C, Operating Humidity : 10%-90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.make phillips,bajaj,surya ,k-lite, crompton,olt,luster

SITC of Color Changing RGBW 70W LED Wall Washer/ Linear Lumianire SITC of Color Changing RGBW 70W LED Wall Washer/ Linear Lumianire surface mounted Narrow/Medium/ elliptical beam wall washer 1000mm luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics. With oughened glass, clear/powder coated. Luminaires are with serviceable DMX 512 Decoder inbuilt with Independent DMX Control Master Slave function ability of Mode Selection, Addressing, Intensity setting and also able to operate with Universal DMX 512 Master Controller. Controller can achieve 16.7M colors. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of Extruded Aluminium with , adjustable Brackets made of Stainless Steel . Impact resistance level should be suitable to site condition minimum IK06. Adequate heat sink with proper thermal management shall be provided. Luminaire should be provided with suitable integral/separate non-integral power supply unit. Fixture shall have Input Voltage 24Vdc and external driver should operate @120-277 VAC, 50/60Hz, THD<15% and PF>0.9. Operating Temperature : -10°C to +45°C, Operating Humidity : 10%- 90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. make phillips,bajaj,surya ,k-lite,crompton,olt, luster

SITC of Color Changing RGBW 18-24W LED Wall Washer/ Linear Lumianire surface mounted Narrow/Medium/ eliptical beam wall washer 1000mm luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temp resistant optics Luminaires are with serviceable DMX 512 Decoder inbuilt with Independent DMX Control Master Slave function ability of Mode Selection, Addressing, Intensity setting and also able to operate with Universal DMX 512 Master Controller. Controller can achieve 16.7M colors. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of Extruded Aluminium with safety glass, adjustable Brackets made of Stainless Steel . Impact resistance level should be suitable to site condition minimum IK07. Adequate heat sink with proper thermal management shall be provided. Luminaire should be provided with suitable integral/separate non-integral power supply unit. Fixture shall have Input Voltage 24Vdc and external driver should operate @120-277 VAC, 50/60Hz, THD<15% and PF>0.9. Operating Temperature,olt,luster

SITC of 36W 3000K LED Wall Washer/ Linear Lumianire surface mounted Narrow/Medium/ elliptical beam wall washer 1000mm luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics. With toughened glass, clear/ powder coated. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of Extruded Aluminium with adjustable Brackets made of Stainless Steel Impact resistance level should be suitable to site condition minimum IK07. Adequate heat sink with proper thermal management shall be provided. Luminaire should be provided with suitable integral power supply unit. Fixture shall have Input Voltage 120-277 VAC, 50/60Hz, THD<15% and PF>0.9. Operating Temperature : -10°C to +45°C, Operating Humidity : 10%-90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements..make phillips,bajaj,surya ,k- lite,crompton,olt,luster

SITC of 15W/mtr IP67 WW 24Vdc flexible strip plane profile allows installation and application in surface mount or flush mount. Uniform, dot-free and smooth lighting performance up to 5M[16.4ft.], Compared with traditional fragile glass and harden/yellowing easily PVC, sheathing material, silicon extrusion technology is an advanced process with high-efficiency production capacity and environmentally- friendly characteristics with aluminum channel

200W 24V SMPS Constant voltage output- 24Vdc, Current o/p- 6.3A max, High power factor >0.97(240Vac& full load), THD<10%, Surge immunity: DM 6KV, CM 10KV, IP67

Supply of Lighting control: DMX splitter 1:4 Cum booster with minimum 4 channel isolated outputs in IP65 Box with 50W 24V CV power supply. 1 channel input, 4 channels distributed output, there is a independently photoelectricity insulation of >3KV between input and output terminals, and output terminals among 4 channels, and 1 bypass channel, BYPASS function for expanding DMX device number. o/p port- 3pin XLR-4, Relay function for amplifying weak DMX/RDM signals and extending the signal transmission distance.

SITC of DMX Controller DMX512, 5-5.5V DC 0.6A, 10 buttons for direct access 2 buttons to change scene + 1 button to change zone, USB & Ethernet for programming/control, Windows/Mac software to set dynamic colors/effects

Programming of DMX controller with Lighting scenes as per approved lighting theme

Supply of DMX cable- Beldon make- DMX Special cable DMX cable (single pair) having one 22AWG pair stranded (7x30) tinned copper conductors, Datalene (FHDPE) insulation, twisted pairs, overall Beldfoil shield (100% coverage) plus tinned copper braid, PVC jacket Cable.

3 Pin male overmoulded connector with 0.75sqmm 3 core cable of length 2 mtr

3 Pin female overmoulded connector with .75sqmm 3 core cable of length 2 Mtr

operaton, maintenance ,security of complete system with ward and watch inclusing programming , testing and commioning and maintenance of seen for two years with programming of different colour pattern as per engineer incharge also AMC of decorative poles