Tata Memorial Centre Tender

Pre-Construction Termite Treatment Step1: Foundation Level Chemical Treatment Step2: Pre Gatka Treatment at plinth level and soil treatment Step 3: Door Frames(Chokhat Level) Treatment with drilling method (Chemical to be used: Imidacloprid 30.5%) Warranty of Termite infestation (5Years)

PCC : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and fixing of Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more in column/ slabs/ footing/ foundations/ Lintels/ plinthbeam/tie beams/ chajja etc.. for R.C.C. work including straightening, cutting, bending, placing in position and binding and including of placing of cover blocks etc. all complete below plinth level and above plinth level up to V level floor.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. and , moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks etc.

Centering and shuttering including strutting, propping etc. and removal of form work for :Columns,, piers, roofs, Slab, abutments, pillars, posts and struts etc up to V floor Level including required scafolding Matarial Shifting and required support as per site requirements and as per direction of EIC.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers up to iii floor Level including required scafolding Matarial Shifting and required support as per site requirements and as per direction of EIC.

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases etc. up to iii floor Level including required scafolding Matarial Shifting and required support as per site requirements and as per direction of EIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

.Concrete of M25 grade with minimum cement content of 330 kg /cum All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum All works above plinth level upto floor V level

Brick work with common burnt clay F.P.S. (non modular) bricks of class 1 designation with average compressive strength not less than 10.0 n/mm2 in foundation and up to first floor Cement mortar 1:4 (1 cement : 4 coarse sand) as per the entire satisfaction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement :4 coarse sand) with Extra for providing and placing in position 2 Nos 6mm/8mm dia. M.S. bars at every third course of half brick masonryas per the entire satisfaction of Engineer-in-Charge.

Providing and Applying of 12 mm thick cement plaster of mix 1:4 (1 cement: 4 coarse sand) for internal surface, including surface preparation work, chicken mess jali fixing , hacking Scafolding/plateform if required etc. as per site requirements and as per direction of EIC.

External cement Plaster thickness of 18 mm in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying, stacking and filling, Dressing of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Complete in all respect includinng filling undulations, preparation of surface even and smooth, sand papering etc. at specific locations as per direction of Engineer in Charge.

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/litre of approved brand and manufacturer, including applying additional coats whereever required to achieve even shade and colour with TWO or more coats.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and fixing ISI marked 35 mm thick flush door shutters including ISI marked Stainless Steel butt hinges with necessary screws, Hnadles, Towerbolt , door stopper etc. conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. :

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be easured):Rectangular or square

Extra for cutting rebate in flush door shutters (Total area of the shutterto be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood 50x12 mm

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With brass cover plate minimum 1.25 mm thickness

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

KOTA STONE FLOORING 25 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

P/F of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and laying 60mm thick faciory made cement concrete interlocking/Green paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : Above 40 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 80 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading welding the pipe etc. complete : 50 to 80 mm nominal bore

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.44) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS:7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-- Make: Polycab, Havells, KEI.

Overall size 25sq.mm (3½ Core) Armoured (On-Surface)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Make: Dowel, Commet

3½ X 25 sq. mm (28mm)

Supply, laying and erection of copper conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS:7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-- Make: Polycab, Havells, KEI.

Overall size 10sq.mm (4 Core) Copper Armoured

Supplying and making end termination with brass compression gland and copper/aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Make: Dowel, Commet

4 X 10 sq. mm (25mm)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. Make: Schneider, L & T, Legrand

6 way (4 + 18), Double door (1 Raw + 1 UPS)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Schneider, L & T, Legrand

6 A to 32 A ratings , SP MCB “C” curve, 10 KA breaking capacity

MCB, 40A, 10KA, TPN

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB/RCBO), having a sensitivity current 30/100 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Schneider, L & T, Legrand

25 A rating, 2 pole RCCB, 30 mA

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Make: AKG, Diplast,

25 mm

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required Make: Polycab, Havells,KEI

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Make: Polycab, Havells,KEI

Group C (Primary Point upto 12.5 Mtrs.)

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. Make: Polycab, Havells,KEI

Group C (Secondary Point upto 12 Mtrs.)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. Make: Anchor, Legrand

6 Module (200mmX75mm)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Make: Anchor, Panasonic

Supplying and fixing suitable size GI box with modular plate and cover in FRLSont on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. Make: Anchor, Panasonic

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 amps modular socket outlets and 2 nos 5/6 amps modular switches, connection etc. as required. Make: Anchor, Panasonic

LIGHT Fixtures Supply,installation,testing and commissioning of LED fixtures having minimum 100Lm/W on wall/beam/slab by means of bracket ,anchor fastener suspended from slab/beam by means of 19 mm dia conduit pipe/down road,ball and socket arrangement,flexible twisted wire/ flexible cable connection etc and GI chain for recessed mounting fitting complete in all respect as directed by Engg. in charge and Wipro make or any other approved make as per instructions of EIC. Make: Wipro, Philips, Havells

Decorative type T5 Luminaire with 1x28W LED Lamp

SITC of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required of following size: Make: Havells, Bajaj, Usha

250 mm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Make: Crompton, Havells, Usha, Bajaj

Supply, Installation Testing & Commissioning of chemical copper earthing of 3 meter long including accessories, and providing masonry enclosure with cover plate.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required for earthing including end termination. Make: Polycab, Havells, KEI

2 x 6 sq. mm

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable of DELTON/SKYTON/Beldon/MOLEX/FINOLEX in the existing surface/ recessed steel/ PVC conduit as required.

4 pair UTP CAT 6- 1 run of Cable

SITC RJ 45 I/O jack with cover plate of Schneider/MOLEX make including 2 module PVC Box. Make: Schneider, Molex, Beldon

SITC Patch cords 3 mtr of D-Link/Schneider/MOLEX

Supplying and Laying of one number armoured OFC cable 6F Singlemode (OM3) loose tube (unitube) on the existing cable tray/surface including tie etc as reqd. Construction type should be PBT (Polybutylene, Terephthalate). Armouring type should be Corrugated Steel Tape Armour (ECCS Tape). Peripheral strength member should be two steel wires (0.9 mm dia) Commercial Standards should be ISO.IEC 11801 - 2nd Edition, type OM3;AS/ACIF S008; AS/NZS 3080 ; TIA/EIA 568.C.3; IEC-60793-1, 60793-2. Make: Schneider, Molex, Beldon

Supply, Installation, Testing and commisioning of 9 U Rack with cable managers,PDB, utility switches complete with all accessories Make: Valrack, Netrack, Dlink

Supply, Installation, Testing and commisioning of 15 U Rack with cable managers,PDB, utility switches complete with all accessories Make: Valrack, Netrack, Dlink

Supply, installation Testing and commisioning of distributed Network switches manageable POE (24] port-cat-6 type, 10BASE-T/100BASE-TX/1000BASE-T, with gigabit interface 2/4 fibre optic port, SFP trans receiver module,POE based), rack mount, along with all the necessary fixing supports, patch cables, etc. with complete accessories. Make: Alcatel, CISCO, Tejas

SITC of Network switch, 24 copper Port X 1G T + 4 SFP X10G SFP+ Managable Non-POE L2, console port,speed of 176 Gbps,MPPS 130 with security feature of ACL, 802.1X, CoA, TACACS+/RADIUS, DHCP snooping, ARP Inspection, IPv6 ND, DoS Attack Prevention, Storm Control,Managed protocol of Telnet, SSHv2 and SNMP v1/v2/v3 support; NTP, FTP, TFTP, SCP, SFTP, Port Mirroring, 8 priority queues, Qos Rate Limiting/Policing, CIR, Shaping, 802.1p, Classification and Remarking with 3 year OEM on site warranty. Make :- Cisco/Tejas

Supply, Installation, Testing, Commissioning of 12 PORT LIU single mode, fully loaded with pigtails, adapter plates, blank plates, splicer tray, patch cords ,etc, duplex LC optical connectors with all the necessary enhanced sliding mechanism based on wheels, with all the necessary wiring, mouning brackets, fixing & support accessories, with splicing etc. Make: Molex, Schneider, Beldon

Supply, installation Testing and commisioning of IP Indoor fixed dome camera, POE based (with maximum wattage of 5 watts per camera), 1/2.7 ” CMOS/ CCD Sensor, Resolution: 2 Megapixels (2048 x 1536) for color;1 Megapixel (1280 x 960) for B/W , Frame rate: CIF- 30 fps, VGA- 30 fps, Mega- 20 fps. H.264 and MJPEG stream, 1 lux colour/0.1 lux BW @ 1/60 sec, , Wide Dynamic Range, Duplex Bi-directional Audio Support, SDHC Memory Card Slot, Megapixel, Supported protocols: TCP/IP, HTTP, FTP,SMTP, DNS, NTP, SNMP,ONVIF Support along with all the necessary mounting brackets, fixing supports, poles, junction box, patch cables, etc. with complete accessories. (Note: vendor to specify the considered lens size) Compatible with HUS user version 5 Software Make: Honeywell, Bocsh, Pelco

Supply, installation Testing and commisioning of Cat-6 Patch cord 1 mtr. Make: Molex, Comscope, Systemax

Supply, installation Testing and commisioning of 24 port Cat-6 patch panel, fully loaded, rack mount complete with I/O socket Make: Molex, Beldon, Schneider

SITC of Fiber 10G SFP required make. As per approval of Network switched all switches will have 4 nos of SFP each will provided with 10G speed Make: Same as Network switch

Supply, Laying and fixing of GI Raceway 100 X 50 MM with cover , anchoring with 8mm thread Rod and bullet fastner.