Public Works Department Tender

TABLE for Court Staff – 1219mm X 609mm X 750mm Supply and Installation of Table top shall be made of 18 mm thick plyboard top shall be liminated with 1mm thick mica , modesty penal 18 mm thick ply board and Gable end 18 mm thick plyboard top shall be liminated with 1mm thick mica. All Exposed edges of pre-laminated board to be sealed Teak ply with veneer polish.Each Table should be provided with 3 drawer having of 3 sliding Drawer .The drawer top, and the drawer made out of 18mm thick ply board the back of the drawer unit is made from 9mm thick ply . The drawer are mounted on rollers slides to enable smooth operation of the drawer as approved by engineer in-charge/employer.

Advocate table – Size -1524mmx609mmx750mm Supply and Installation of Table top shall be made of 18 mm thick plyboard top shall be liminated with 1mm thick mica , modesty penal 18 mm thick plyboard and Gable end 18 mm thick plyboard , All Exposed edges of pre-laminated board to be sealed Teak ply with veneer polish.. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corner left after processing, Table as approved by engineer in-charge/employer

Executive TABLE – -2134 x914 x750mm withSide Unit Extention: W 1050mm x D 450mm x H 750mm Supply and Installation of Table top shall be made of 20 mm thick Teak ply with veneer polish consisting 8mm thick glass of size same as table top , modesty penal 20 mm thick and Gable end 20 mm thick Teak ply with veneer polish , All Exposed edges of pre-laminated board to be sealed Teak ply with veneer polish. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corner left after processing.Each Table should be provided with 3 drawer having of 3 sliding Drawer .The drawer top, and the drawer made out of 18mm thick Teak ply with veneer polish the back of the drawer unit is made from 9mm thick ply. Side Unit Extention top shall be made of 20 mm thick Teak ply with veneer polish , modesty penal 20 mm thick and Gable end 20 mm thick Teak ply with veneer polish , All Exposed edges of pre-laminated board to be sealed Teak ply with veneer polish. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corner left after processing. It should be provided with 3 drawer having of 3 sliding Drawer .The drawer top, and the drawer made out of 18mm thick Teak ply with veneer polish the back of the drawer unit is made from 9mm thick ply Table as approved by engineer in-charge/employer.

Smart Executive Leather Chair Chair Frame: Metal Upholstery Cover: Leather Finish Seat: Patented SmartGRID Technology Armrest: Metal arms with heavy nylon armrests Base: Heavy Duty Metal Base Gaslift: Class 4 Samhongsa BIFMA Certified Gas Lift Mechanism: Press Tilt Mechanism Castors: 60 mm Maximum Weight load: 150 kgs Product Dimensions: L 75 x B 46 x H 140 inches Use / Suitability: Gaming Zone & WFH Setup As approved by engineer in-charge/employer.

Executive TABLE – -1829mm x 914mm x 750mm (Tehsildar) Supply and Installation of Table top shall be made of 20 mm thick Teak ply with veneer polish consisting 8mm thick glass of size same as table top , modesty penal 20 mm thick and Gable end 20 mm thick Teak ply with veneer polish , All Exposed edges of pre-laminated board to be sealed Teak ply with veneer polish. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corner left after processing.Each Table should be provided with 3 drawer having of 3 sliding Drawer .The drawer top, and the drawer made out of 18mm thick Teak ply with veneer polish the back of the drawer unit is made from 9mm thick ply. Table as approved by engineer in-charge/employer.

Conferance Table – 81000mm X 3200mm X 750mm Supply and Installation of Table top shall be made of 18 mm thick plyboard top shall be liminated with 1mm thick mica , modesty penal 18 mm thick ply board and Gable end 18 mm thick plyboard top shall be liminated with 1mm thick mica. All Exposed edges of ply board to be sealed with 1mm thick mica. as approved by engineer in-charge/employer.

Waiting Area chair 3 seater- Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm.As approved by engineer in-charge/employer.

Sofa Set with Centre Table 2S+2S+3S Sofa inner frame structure shall be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU) foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16 to 18 inches and depth shall be between 20-22 inches. Two seater sofa size - 1067L x 735D x 820H.Three seater sofa size - 1625L x 735D x 820H.

Center Table 1067 mm x 1067mm Supply and Installation of Table top shall be made of 20 mm thick Teak ply with PU polish consisting 8mm thick tinted designed glass of size same as table top , modesty penal 20 mm thick and Gable end 20 mm thick Teak ply with PU polish , All Exposed edges of pre-laminated board to be sealed Teak ply with PU polish. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corner left after processing. As approved by engineer in-charge/employer.

Almirah for Tehsil Office W 914 mm x D 533mm x H 2132 Metal Almirah : Overall Size shall be 900 x 400 x 2015 (WDH) mm. The complete storage shall have metal shutter and metal top. The construction and material of storage body shall be of 0.6mm thick CRCA and skirting shall be of 0.6mm thick CRCA sheet. The storage top shall be of 0.6mm thick CRCA sheet and shutters shall be of 0.6mm thick CRCA sheet. Shelf shall be mounted with the Metal shelf support made of 2mm thick CRCA sheet with Nickel or Chrome plating. The construction shall be aesthetically appealing completely welded/ knockdown. Legs shall be fitted with M10 screw leveler with height adjustment upto 12mm to 15mm. 3 point lock of Ebco/hettic make shall be used. Recessed handles of Hettich/ebco make shall be provided. Finish shall be powder coated Tolerance of +/- 10mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in thickness & sizes of pipe.As approved by engineer in-charge/employer.

Visitor Chair Supply and installation of Stainless Steel framed visitor chair with PU finish arm rest.Seating and Back area should be cushioned and properly covered with Faux leather material As approved by engineer in-charge/employer.

Teak Wood Visitor Chair Supply and installation of chair made with high quality teak wood. With 4 legs and all legs and frame made of teak wood should be Melamine polsihed. Total height of chair 940mm bottom outer frame 560 mm x 585 mm back outer frame size 533 mm x 506mm arm rest height should be at 600 mm. seating area should be cushioned and properly covered with leaterite or with polystered material As approved by engineer in-charge/employer.

Teak Wood Visitor Chair Supply and installation of chair made with high quality teak wood. With 4 legs and all legs and frame made of teak wood should be PU polsihed. Total height of chair 940mm bottom outer frame 560 mm x 585 mm back outer frame size 533 mm x 506mm arm rest height should be at 600 mm. seating area should be cushioned and properly covered with leatherite or with polystered material As approved by engineer in-charge/employer.

Teak Wood Visitor Round Table Supply and installation 457mm Round double slab table with clear height of 480mm frame with four legs made of teak wood should be Melamine polsihed. As approved by engineer in-charge/employer.

Teak Wood Court Chair Supply and installation of Court chair made with high quality teak wood. With 4 legs and all legs and frame made of teak wood should be PU polsihed. Total height of chair 1219 mm bottom outer frame 609 mm x 560 mm back outer frame size 737 mm x 585mm arm rest height should be at 600 mm. seating area should be cushioned and properly covered with polystered material As approved by engineer in-charge/employer.

Teak Wood Leatherite Court Chair Supply and installation of Court chair made with high quality heavy teak wood. With 4 legs and all legs and frame made of teak wood should be PU polsihed. Total height of chair 1219 mm bottom outer frame 609 mm x 560 mm back outer frame size 737 mm x 585mm arm rest height should be at 600 mm. seating area should be cushioned and properly covered with leatherite material As approved by engineer in-charge/employer.

MID Back Chair for Staff Mid Back chair, Mesh back, Cushion Seat, Adjustable PU Pad arms, Auto Weight Slider ,Mechanism,Gas Lift, AluminiumBase with Nylon. Cotors Overall Height - 1020mm Outer Width - 650mm Overall Depth - 700mm Seat Width - 500mm Seat Depth - 480mm Seat height from ground - 420mm Back Width - 420mm Back Height from seat - 580mm Back Size - 700mm Gas Lift - 100mm All dimensions have a toierance of ±10mm. As approved by engineer in-charge/employer.

Roller Blind Supply and installation of roller with the Spfecification of Fabric Thickness 0.6 MM,Fabric Composition-Polyster / Cotton.Light Fastness As approved by engineer in-charge/employer.

Curtains with Rolling Channals Supply and installation of Curtains of premium cotton quality with rolling channals roller As approved by engineer in-charge/employer.

Mid Back Chair The overall size of Chair shall be height 870 to 970 +/-5 mm, Back Width 415 mm at Top and 450mm at bottom, Seat Width 480 +/-5 mm, Seat Depth 420+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. over all chair width should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat and back shall be upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The back frame shall be made up of PPGF and the injection molded in black color, armrest also in black color. The Chair should be provided with center tilt two position lock Mechanism. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Fixed arms connected to seat and back in the same colour. The mechansim shall possess seat to back recline ratio of 1:1. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The base shall be made up of nylon glass filled black color.Tolerance of +/- 5mm to be considered for dimensions Length, Depth & height and tolerance of 5% to be considered in thickness.

High Back Chair for Tehsildar and Naib Tehsidar The overall size of Chair shall be : width 600 +/-5mm, depth 640 +/-5mm. Total height 1170 to 1270 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20%. PU Adjustable Lumbar Support full length of size 365 mm, 110 mm height and 25mm thickness. The Chair should be provided with Self Calibrating Multilock Mechanism that should adjust the tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon base shall be provided.Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Tolerance of +/- 5mm to be considered for dimensions Length, Depth & height and tolerance of 5% to be considered in thickness.

Desk Table Main Table of size 1500 x 750 x740 (WDH) .The worktop shall be made up of 25mm thick PLPB E1 norms duly finished with 2mm pvc edge band. The Modesty shall be made of 18mm thick pre laminated partical boards with E1 norms and all visible side 2mm pvc edge bending. Modesty height shall be 450mm .The table understructure shall be made of 18mm thick PLPB E1 norms duly finished with 2mm pvc edge band. Mobile Drawer Unit : It shall be of size of 400 x 450 x 600 (WDH) mm made up of 18mm thick Pre-laminate particle board as per E1 norms and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Drawer front & sides shall be made up of 18mm, back 9 mm thick pre laminated particle board of E1 grade with visible edges sealed with 2mm PVC edge band. The drawer side surface shall be provided with finger groove handle-less design. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be provided. Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The furniture brand shall have quality & safety related certifications that is: ISO 9001, ISO 14001, ISO 45001, ISO 50001, AIOTA for Educational Furniture & Office Furniture, IDM (India Design Mark) for atlest five products by India Design Council, BIS & (IGBC) Gold rated factory certification (Indian Green building Council), GRIHA (Green Rating for Integrated Habitat Assessment) & Green Pro certification by CII (Confederation of Indian Industries). ISO certificates should be from a NABCB/ NABET / QCI accredited agency. Product should be Greenguard by UL & Bifma Level2 certified. The certiifcates mentioned in the specification must be issued by an authorized certificate issuer. The certificates must mention product name along with manufacturers name.

Computer Table W1200xD750xH750 Main Table of size 1200 x 750 x740 (WDH) .The worktop shall be made up of 25mm thick PLPB E1 norms duly finished with 2mm pvc edge band. The Modesty shall be made of 18mm thick pre laminated partical boards with E1 norms and all visible side 2mm pvc edge bending. Modesty height shall be 450mm .The table understructure shall be made of 18mm thick PLPB E1 norms duly finished with 2mm pvc edge band. Mobile Drawer Unit : It shall be of size of 400 x 450 x 600 (WDH) mm made up of 18mm thick Pre-laminate particle board as per E1 norms and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Drawer front & sides shall be made up of 18mm, back 9 mm thick pre laminated particle board of E1 grade with visible edges sealed with 2mm PVC edge band. The drawer side surface shall be provided with finger groove handle-less design. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be provided. Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.The furniture brand shall have quality & safety related certifications that is: ISO 9001, ISO 14001, ISO 45001, ISO 50001, AIOTA for Educational Furniture & Office Furniture, IDM (India Design Mark) for atlest five products by India Design Council, BIS & (IGBC) Gold rated factory certification (Indian Green building Council), GRIHA (Green Rating for Integrated Habitat Assessment) & Green Pro certification by CII (Confederation of Indian Industries). ISO certificates should be from a NABCB/ NABET / QCI accredited agency. Product should be Greenguard by UL & Bifma Level2 certified. The certiifcates mentioned in the specification must be issued by an authorized certificate issuer. The certificates must mention product name along with manufacturers name.