Baba Farid University Of Health Sciences Tender

Dismantling glazed tiles (to be carefully removed).

Dismantling cement conglomerate floors 25mm to 50mm thick without concrete base

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement: 4 fine sand), complete. ( Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished ). Size 600x600 mm (749+5.35%0= 789.00

Conglomerate floor 40mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material

Kota stone slab 20-25 mm thick flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

Golden Champ, wood, doors, shutter, windows, shutter including hinges, screws, chocks, cheats, stops, cords etc. complete fixed in position 35 mm thick

Wire Gauge Golden Champ wood door shutter without springs housed in chowkhat. 35 mm thick

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position. Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges 35mm thick

Providing & Fixing glass panes with nails and putty or wooden strip complete in all respect. 4mm thick or 10.78 Kg/ sqm

115mm thick brick wall in cement sand mortar 1:5 without reinforcement in superstructure

12.5mm thick cement plaster 1:5 on walls

Providing and fixing commercial plywood 18mm thick

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc. Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading.

Providing & fixing 16 gauge stainless steel pipe railing of grade 304 duly fixed on steps with the help of bolts grouted on steps with hand rail and newel post of 50mm dia Stainless steel pipe, Balusters of 40mm dia Stainless steel pipe and guard 3 Nos of 15mm dia Stainless Steel pipe complete in all respect

Add Public work as per item CSR 2020

Boundary wall First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level

Cement pointing 1;2 deep variety

20 mm thick cement plaster 1:4 on walls

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Providing and fixing barbed wire fencing over boundary wall along angle iron post complete

Providing and fixing concertina coil fencing over angle iron post including binding upto the angle/ barbed wire required complete

Applying priming coat with metal primer on new steel or iron work including preparation of surface. angle iron post 50x50x6 mm

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm

Electrical Work Replacement of PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in existing heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), PVC Bush, bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm,1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc. including the cost of above material, cutting and filling up of chases Wiring fan point (Without fan box) CSR 34.08 (i) a (666.00 + 20% = Rs.799.20 +5.35% =841.95 )

Wiring light point CSR 34.08 (ii) (376.00 +20% =Rs .451.20 + 5.35 %= Rs.475.33)

Wiring 6Amp. Plug control comprising wall socket point CSR 34.08 (v) ( 292.00 + 20% =Rs.350.40 + 5.35% =Rs.369.14)

Wiring 16/20Amp. power plug control point CSR 34.08 (vi) (438.00 + 20% =Rs.525.60 + 5.35%=Rs.553.71

Supply and erection of PVC insulated FR single core Unsheathed copperconductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1.5sq.mm (Un-sheathed) CSR 34.09 (ii) (18 + 30% = Rs.23.40 + 5.35% = Rs.24.65)

Overall size 4sq.mm (Un-sheathed) CSR 34.09 (iv) (39 + 30% =Rs.50.70 + 5.35% = Rs. 53.41)

PVC insulated & PVC sheathed aluminium conductor cable Overall Size 10mm² (1/1.40mm) Twin Core CSR 34.34 (ii) C(38 + 10% = Rs 41.80 + 5.35% =Rs 44.03 )

Overall size 10sq.mm (4Core) Un-armoured (On-Surface) CSR 34.10 C (xxxvi) ( 94.00 + 25% = Rs.117.25 + 5.35% = Rs.123.78)

Supply and erection of sheet metal Iron Clad Switches on existing surface with G.I. bolts & nuts/ rag bolts and nuts etc., according to the size of holes in the body of the enclosure including connections with suitable size of thimbles and bonding to the existing earth as Per PWD General Specifications:-ICTPN Switch 63amp., 415volts CSR 34.18 (vi) (2904.00 + 35%=Rs.3920.40 + 5.35% = Rs. 4130.14)

Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-MCB Single Pole 6-32amp. (10kA, Curve-C) CSR 34.16 A (ii) (134+35% = Rs.180.90 + 5.35% = Rs.190.57 )

Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:- MCCB Four Pole 125amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting CSR 34.23 C (iii) ( 5576 + 40% = Rs.5.35% = Rs.5916.45

Supply & erection of Bakelite batten holder large size.CSR 34.15 (xxvii) (34 + 15% = Rs.39.10 + 5.35 % = Rs. 41.19)

Supply and erection of sheet metal double door vertical distribution boards IP 43-IK09 metal door (dust protected) as per IS:8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars for each phase, 2 Nos. shrouded neutral bars, 2Nos. earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting MCCB's as incomer and outgoings SP/TP miniature circuit breakers in the distribution board as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc.:-P&N Double Door Vertical DB's 8 way each (With provision of FP MCCB upto 125amp.)CSR 34.17 (xvi)b (7981 +15 %=Rs.9178.15 +5.35% =Rs.9669.18 )

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-Overall size 35sq.mm (3½ Core) Unarmoured (On-Surface)CSR 34.10 C(xxiii) ( 170 +25% =Rs.212.50 +5.35% =Rs.223.86 )

Supply and erection of LED flood light 100 watt Make Bajaj/ Crompton/ Havells Outdoor IP65 Rated Water of (Cool Day Light 6500K ) with inbuilt driver which protects against unstable power condition or sudden peaks in AC Voltage of upto 4KV, High Brightness & Energy Saving LED lights have a strong and high quality light output of upto 100 Lumens / watt AC220-240V, 50/60Hz . complete in all respects with 2 year warranty

Supply and erection of High quality aluminium extruded with decorative end caps glazed LED batten of Make Jaquar Item Code LGLZ01x020XC or Its equilant Make and Cat. of Philips / Halonix including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer in-charge at site.

S/E of Energy Saving Fan Ceiling Fans 1200mm sweep ( 48" ) having two ball bearing but without regulator including flexible wire & petty material etc. for connections complete with erection, connections and testing etc. complete in all respect as approved and desired by the Engineer-in-charge at site. Make :- Crompton Entrust 50-5Star or its equillant make Halonix

Supply and erection of 12" Heavy Duty Exhaust fan (HDEF) (300mm-900RPM) Single Phase of make Crompton Model EXHD 300-6-1 or Its equialant Make Havell's Turbo Force SP / GE / Halonix ISI marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and louver shutter complete in all respects as appd. and desired by the Engineer in-charge at site

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-Overall size 300 sq.mm (3½ Core) Unarmoured (Loose)CSR 34.10D (xxxi) (1029 + 25% = Rs.10286.25 +5.35% =Rs. 1355.06 )

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-Double Walled Corrugated HDPE Pipe 120/103.5mm (Outer/ Inner dia.)CSR 34.37A (iV) (276+ 5.35% =Rs. 290.76)

Designing, Supply, Erection, Testing & commissioning of indoor Type LT cubical panel enclosure (dust, vermin and interchangeable modules with facilites for extensions or reduction as per the space or requirments). The Panel shall be suitable for operation at 415+6% Volts, 50HZ, 3 phase 4 wire & earth system. The assembly manufacturer should be ISO approved and CPRI tested for short circuit of (minimum 50kA) as well as IP degree of protection (IP 54/55). Fabrication:- Panel shall be made from 14/16 SWG CRCA sheet, conforming to IS 8623/1977-82. The sheet metal used for the fabrication of control panel will be 2mm for load bearing member’s door and fittings plates etc. the partitions and other non load bearing members will be fabricated out of 1.6mm sheet, the sheet will be of mild steel CRCA type. The base channel will be made out of 75 x 40 x 5mm rolled channel. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The panel door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. Minimum depth 400mm / wide 300 mm for busbar/ Cable ally at the front of the panel. The panel will be free standing floor mounting type having provision for cable entry from bottom/top with cable glands etcThe fabrication should be such that all the member i.e. vertical/horizontal should be detachable type i.e. total bolted. In case of any changes required at site. it should be possible then and their self without any cutting or welding. The fabrication of the panel in 3B construction fully compartmentalized type i.e. bus bar chamber as well as the cable chamber should be totally isolated from the feeder chamber. Where there crossing of the wire or bus links. It should have proper rubber gourmets or non-hygroscopic material. No live part should be in visible condition.

Painting:- The sheet metal is sprayed with corrosion resistant etch Primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work . Busbars:-The panel shall be provided with TPN aluminium busbar of suitable size according to the size of MCCB's. Busbar shall be of high conductivity (53% to 58%) E91-E Grade aluminium (1A/Sq.mm). All Busbar will be air insulated with codified in Red, Yellow, Blue & Black as per standard for cable termination with the help of extended busbar only with proper adjustable cable supports. The main busbar would be supported upon non-hygroscopic SMC/DMC supports. Metering:-The panel shall be completed with digital metering unit (with selector switches, voltmeter & ammeter) epoxy insulator, gasket, PVC sleeves, CT's & L.E.D. type indicator etc. Manufacturer of Panel should be CPRI Approved (Approval not older then 5 years) & ISO certified (Manufacturer workshop as per ISO 9001: 2015 standard) The Concerned contractor shall be approved the detailed drawing of panel with complete specification from the Engineer in charge at site. Detail of capacities of MCCB's to be installed in the cubical panel Enclosure (Excluding the cost of MCCB's) as per following: LT Panel enclosure having space for 1No. Incomer MCCB 400Amp. and 10Nos. outgoing MCCB's 40amp. to 160amp. according to the requirement at site (Approx. size 2025 x 1800 x 400mm) 34.23A VII (117700.00 + 15% = Rs.135355.00 +5.35% = Rs.142596.49)

Supply and erection of MCCB Four Pole 400amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting 34.23 C VIII (23143 + 40% = Rs.32400.20 + 5.35% = Rs.34133.61)

Supply and erection of MCCB Four Pole 100amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting 34.23 C II (4493.00 + 40% = Rs.6290.20 +5.35% = Rs.6626.72)

Supply and erection of MCCB Four Pole 160amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting 34.23 C IV (6877.00 + 40% = Rs.9627.80 + 5.35% = Rs.10142.88)