Power Cable Tenders

Details: Routine Preventive Breakdown and Shutdown Maintenance of 415V AC Switchgears at main Plant and CHP Switchgears 220V DC110V AC power supply system ESP Control Panels including HVR Transformers and rapping motors control Hydrogen Plant local control panels, Micro Hydel Plant LT Switchgear and associated equipment local push button stations and power receptacles LT Power and control cables installed at various locations under Electrical Mtc. Cell No.1 of 4X210MW Stage-II and III of GGSSTP, Rupnagar

Description: Supply & Installation Of Trans Receiver 25 Watt Vhf Digital Radio Set For Frequency Band 146 Mhz-174 Mhz Full Band Along With 6 Db/6.5db Gain Omni Directional Ground Plane antenna Rg - 217 Low Loss Cable Cable Of 30 Mtr. Length For Connecting Antenna Complete with Connectors,microphone With Press Too Speak Switch With Coil Cord Cables, Smps power Supply 12v, 10amp And Connector For Connecting Power Supply . Equipment Must be Compiled With Rdso Specification No.rdso /spn/tc/107/2018 Version 2.0 Or Latest

Details: Shifting Of Existing Scrap 16/20mva, 66kv/11kv Transformer From Spare Transformer Bed To Designated Location As Per The Directions Of The Engineer In Charge At 66kv Switchyard. Dismantling With Ceig Approval & Shifting Of 16/20mva 66kv/11kv Bank Generator Transformer From Existing Transformer Yard To Spare Transformer Bed Present At 66kv Switchyard Including Dismantling Of Marshalling Box, 11kv Ht Cable Termination, Removing Of Control Cables, Mulsifyre And Fire Hydrant Main Pipe With Demolition Of Fire Hydrant Support Pedestal Etc. Shifting Approx 200 Meters With Wheel Direction Change. Site Testing And Report Submission. Erection, Site Testing & Commissioning Of New 16/20mva, 66kv/11kv Generator Transformer Including Supply, Laying And Termination Of 1.5sqmm Armoured, 19 Core Cable, Length Approx. 100mtrs From Marshalling Box Up To Control Room Required For Protection, Oil Filling And Filtration, Termination Of Power Cables From Acdb To Marshalling Box, Re- Erection And Painting Of Mulsifyre System & Support Structures, Fire Hydrant Pipe With Re-construction Of Support Pedestal Etc. Further, Obtaining Ceig Permission For Commissioning Of New Mahati Make Transformer Including Liasoning Work From Electrical Inspectorate, Gok & Other Govt Department As Per The Prevailing Rules And Replacement, Testing & Commissioning Of Bank-1 Rtcc Panel With Newly Supplied M/s Mahati Industries, Pune Make Rtcc Panel Including Releasing Of Existing Control Cable And Termination Of New Control Cable And Shifting Of Released Rtcc Panel To Kpcl Store. Obtaining Ceig Permission For Commissioning Of New Mahati Make Transformer Including Liasoning Work From Electrical Inspectorate, Gok & Other Government Department As Per The Prevailing Rules. And Replacement, Testing & Commissioning Of Bank-1 Rtcc Panel With Newly Supplied M/s Mahati Industries, Pune Make Rtcc Panel Including Releasing Of Existing Control Cable And Termination Of New Control Cable And Shifting Of Released Rtcc Panel To Kpcl Store.

Description: CATEGORY: 5MP Outdoor Bullet IPC Camera , 4MP Outdoor Bullet IPC Camera , 16 Channels Network Video Recorder , 6 TB Surveillance Hard Drive , 8 Port POE 8 PLUS 2 SFP Switch , 8 Port POE Switch 8 plus 2 , 8 Port SFP Switch with 2x1G Uplink , 8 Port 8 PLUS 2 SFP Switch , 1G 20km SFP Module , 1KVA LI UPS , Type III 6S Surge Protector , AC round Cable , Cat6 Patch Cable , 6F Unarmored OFC , POE Junction Box , 4K HDMI Cable , Cat6 UTP Cable , 6Ux600mm Wall Mount Rack with Tray , Wireless Mouse , 43 INCH 4K UHD Smart LED TV , Custom Outdoor Housing Box , Cat6 Outdoor UTP Cable , Cabling Job Work , Supply of conduit pipes accessories as required for Power and Cat 6 cable Laying , Electrical I O cabling and Earthing at NVR Switch Racks points Job work , Supply and Erection of 4m GI Pole with Cantilever Clamps including base civil work , CCTV entire setup Installation Testing and Commissioning with 1 Year onsite AMC

Description: CATEGORY: Dual Frequency Main Digital Indicator Display , Recorder , Repeater Units Training Bridge_ Bridge Wing_docking console Port and STBD , Transducer Suitable for 33 KHz with 20 Mtrs of cable , Transducer suitable for 210 KHz with 20 Mtrs of cable , Cable from Junction box to main unit of Echo sounder_200m approx , Stuffing tube , Transducer casing , Junction boxes IP_56 , Power supply unit for 230V AC 24 V DC with necessary connectors , All Cables will be in OEMs scope of supply a Cable for Repeater_300m approx. , OBS , Documentation , TRANING , SERVICE OF ENGINEERS FOR INSTALLATION , SERVICE OF ENGINEERS FOR CONNECTORISATION , SERVICE OF ENGINEERS FOR CALIBRATION , SERVICE OF ENGINEERS FOR HATS , SERVICE OF ENGINEERS FOR SATS , MONTHLY WARRANTY EXTENSION CHARGES , Extra Man Days 1st Year EXTRA MAN-DAYS PER MANDAY CHARGES , Extra Man Days 2nd Year EXTRA MAN-DAYS PER MANDAY CHARGES SHALL BE OBTAINED , NMEA Buffer unit for Echosounder , Digital Depth Indicator Display Flush Mounting type Loc Slave display in Training bridge , Distribution unit , Printer operating on 230V AC_24V DC power supply and printer cable of standard Length , 2000 sheets endless paper

Details: CATEGORY: Open Jaw Wrenches (Spanners) as per IS 2028 (Q3) , Dismantling of Old Us Distribution Boards alongwith its all accessories i.e. MCCB MCB wiring etc , Dismantling Existing UG Us serviceable cable of any type of following sizes a. 10 Sqmm 2 Core 10 Sqmm 4 Core 25Sqmm 4 Core 35 Sqmm 3.5 Core 50 Sqmm 3.5 Core. , S and L and testing cable XLPE PVC bedded galvanized steel strip or wire armoured electric power cables 1100 Volts SIZE. 10 Sqmm 4 Core. , AS PER SERIAL NO. 3 BUT SIZE 16 Sqmm 4 Core , AS PER SERIAL NO. 3 BUT SIZE 25 Sqmm 4 Core , AS PER SERIAL NO. 3 BUT SIZE 35 Sqmm 3.5 Core , AS PER SERIAL NO. 3 BUT SIZE. 50 Sqmm 3.5 Core , Relaying of existing cable XLPE Insulated galvanized steel strip or wire armoured electric power cables 1100 Volts 10 Sqmm 4 Core 2Core , AS PER SERIAL NO. 3 BUT SIZE 16 Sqmm 4 Core. , AS PER SERIAL NO. 3 BUT SIZE 25 Sqmm 4 Core. , AS PER SERIAL NO. 3 BUT SIZE 35 Sqmm 3.5 Core. , AS PER SERIAL NO. 3 BUT SIZE 50 Sqmm 3.5 Core , M and L for Excavation in trenches upto 1.5m deep Hard dense soil , M and L for Sand filling in trenches including watering and consolidation , M and L for removing of surplus excavated soil , M and L for Returning and filling of surplus excavated soil , Supply and laying Burnt clay fly ash building bricks designation 75Kg cm2 complete all as specified. , M and L for Floor of tiles PCC Footpath cutting through existing PCC floor Footpath approx size width 15cm or as required X 60cm as required , SPN Distribution Board 8 way 230V 50Hz IP54 and IK09 Suitable for Surface mounting with 100 A copper Busbar for each phase , S and F Distribution Box 4 way 430V 50Hz IP54 and IK09 Suitable for Flush mounting and Surface mounting with 100 A copper Busbar for each phase , S and F Distribution Box 4 Module 230V 50Hz IP65 and IK09 classII weatherproof cabinets Door and Cabinet fully reversible Removable chassis and faceplates , S and F Automatic changeover with current limiter ACCL SPN 30A 30A Automatic source chage over between Mains and Generator supply Break , S and F MCB SP 240V 10 KA B curve miniature circuit breaker MCB of single poles and current carrying capacity 6 to 32 AMP , M and L for Wiring for circuit submain wiring alongwith earth wire with the following sizes of FR is PVC insulated copper conductor single core cable , Earthing for poles and other machinery equipment using 4 mm GI wire as earthing lead and MS galvanized plate of size 60 cm x 60 cm x 6 mm , S and F Cable Junction Box, made of CRCA Sheet Single door outdoor type factory made and assembled of size not less than 450x150x450 , M and L for plain concrete cement 1.3.6 type C2 using 40mm graded coarse aggregate for foundation of Busbar Box including necessary form work , M and L for Plywood of 09 mm thick grade BWR type BB fixed with screws to puff panel work complete for fixing of DBs , M and L for Straight through LT cable heat shrinkable jointing kit suitable for LT UG of following sizes cable complete a. 10 Sqmm 4 Core. , M and L for fixing of MCCBs in replacement of 100 Amps 3 Pole 415 Volts thermal nd magnetic adjustable type 0.8 to 1In Magnetic Adjustable 5 to 10In , M and L for fixing of MCCBs in replacement of 125 Amps 3 Pole 415 Volts thermal nd magnetic adjustable type 0.8 to 1In Magnetic Adjustable 5 to 10In , S and Fix HDPE Pipe of 50mm dia for protection of cable under the floor etc complete all as specified and directed

Details: Description:- Supply Of High Mast Tower Of 20 Mtr. Height In Two Sections Suitable For A Wind Speed Of 180 Km/hr. ( 50 M/s ) Made From Steel Plates And Continuously Tapered Of Polygonal Cross Section. The Entire Mast Should Be hot Dipped Galvanised After Fabrication Internally And Externally In Accordance With Bs 729. All Steel Used In The construction Of Mast Complies With Bs En 10 025 Of Appropriate Grade And Welding Is In Accordance With Bs 5135 and Comprising With Lighting Finial & Earthing Terminal, Top Pulley Assembly, Double Drum Winch, Head Frame & lantern Carriage, Stainless Steel Wire Rope Having 7/19 Construction ( The Central Core Is Also Ss ) With A Grade Of aisi 316 Of Breaking Strength 2350 Kgs, Winch Driving Power Tools (motor), Multi Core Flexible Round And Sheathed copper Power Trailing Cable (2 Nos.) With Cable Junction Box (2 Nos.) Including Aviation Obstruction Warning Light, timer For Automatic Switching Operation Of Luminaires And All Other Accessories. ( Make - Utkarsh / B.p. Projects / crompton / Bajaj / Surya )

Details: Description:- Supply Of High Mast Tower Of 20 Mtr. Height In Two Sections Suitable For A Wind Speed Of 180 Km/hr. ( 50 M/s ) Made From Steel Plates And Continuously Tapered Of Polygonal Cross Section. The Entire Mast Should Be hot Dipped Galvanised After Fabrication Internally And Externally In Accordance With Bs 729. All Steel Used In The construction Of Mast Complies With Bs En 10 025 Of Appropriate Grade And Welding Is In Accordance With Bs 5135 and Comprising With Lighting Finial & Earthing Terminal, Top Pulley Assembly, Double Drum Winch, Head Frame & lantern Carriage, Stainless Steel Wire Rope Having 7/19 Construction ( The Central Core Is Also Ss ) With A Grade Of aisi 316 Of Breaking Strength 2350 Kgs, Winch Driving Power Tools (motor), Multi Core Flexible Round And Sheathed copper Power Trailing Cable (2 Nos.) With Cable Junction Box (2 Nos.) Including Aviation Obstruction Warning Light, timer For Automatic Switching Operation Of Luminaires And All Other Accessories. ( Make - Utkarsh / B.p. Projects / crompton / Bajaj / Surya )

Details: Description:- Supply Of High Mast Tower Of 20 Mtr. Height In Two Sections Suitable For A Wind Speed Of 180 Km/hr. ( 50 M/s ) Made From Steel Plates And Continuously Tapered Of Polygonal Cross Section. The Entire Mast Should Be hot Dipped Galvanised After Fabrication Internally And Externally In Accordance With Bs 729. All Steel Used In The construction Of Mast Complies With Bs En 10 025 Of Appropriate Grade And Welding Is In Accordance With Bs 5135 and Comprising With Lighting Finial & Earthing Terminal, Top Pulley Assembly, Double Drum Winch, Head Frame & lantern Carriage, Stainless Steel Wire Rope Having 7/19 Construction ( The Central Core Is Also Ss ) With A Grade Of aisi 316 Of Breaking Strength 2350 Kgs, Winch Driving Power Tools (motor), Multi Core Flexible Round And Sheathed copper Power Trailing Cable (2 Nos.) With Cable Junction Box (2 Nos.) Including Aviation Obstruction Warning Light, timer For Automatic Switching Operation Of Luminaires And All Other Accessories. ( Make - Utkarsh / B.p. Projects / crompton / Bajaj / Surya )

Description: CATEGORY: pandaal balli phrem par , parade , Kanat , darii , jute matting , chauki , Sofa , central table , mej , mej posh , carpet , side piece , stage , dias , chair fancy , chair plain , barricading one line , barricading two lines , barricading three lines , barricading four lines , peshaab ghar , latrine , Kandal , gilaas , baalli , jag , tre , barrier , Tripal , office chair , mej kaa phil , chaadar , sidhi , Tin sheet size 10 x 3 feet , Tin sheet size 12 x 3 feet , majadur , pharsh , naad , machaan , barph ki silli 50 KG , LED bulb 20 watt may sviira by taar sahit , Bulb 100 watt may sviira by taar sahit , Bulb 200 watt may sviira by taar sahit , tube light 40 watt , search light , halogen 50 watt , generator taar sahit 05 by 7.5 KVA Pratidin indhan sahit , generator taar sahit 05 by 7.5 KVA Pratidin indhan rahit , generator taar sahit 40 by 60 KVA Pratidin indhan sahit , 40generator taar sahit 40 by 60 KVA Pratidin indhan rahit , changer board 32 amps , earthing 220 volt , main line wire in meters , Cable 4 Core 3 Phase 7 by 20 Cable , Main Line Wire Single Phase 7 by 20 Cable , Sub main line wire 3 by 20 3 by 22 Cable , Power point 05 Amp for computer , Power point 15 Amp for photo state machine , Autocut Switch MCB 32 Amp , emergency light , pankhe , ceiling fan , pedestal fan , Cooler , sound system full set , horn , mike , loudspeaker , column speaker , line for mic , amplifier , sound box