Odisha Tourism Development Corporation Limited Tender

Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland slag cement (PSC) with 40 mm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes all materials and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per the instruction of the Engineer-in-Charge.

Providing and laying plain cement concrete of (1:2:4) in foundation bed and floors using 12 mm. Size black hard crusher broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required for the work etc complete as per the instruction of the Engineer-in-Charge.

Supplying, fitting and fixing of approved quality badminton poles (fixed on ground) invariable black or dark Green polyethylene netting of 15-20mm of P.V.C. coated G.I. chain link jally of 8 SWG (2"x2") size fixed to M.S. round pipe (50*50)mm medium duty post of size (vertical member) @ 1.85m C/C stay of M.S. angle (25x25)mm 3.7mtr C/C and horizonal member of M.S. angle(25x25)mm @ 1.5 mtr C/C tied within 25mm M.S. flat in both direction (horizental and vertical) by means of fixing M.S.nuts and bolts of approved size with two coats of enamel painting over a coat of primer to M.S. members including cost of all materials labour welding drilling holes, nutbolts T&P etc complete as per direction of Engineer-in-charge (The pipes, angles and flats should be SAIL/Zindal/TATA MAKE).

Providing and painting two coats with synthetic enamel paint over a coat of red oxide primer of approved quality and approved shade confirmming to ISI on Wood work to give an even shade in all floors at all height including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge.

providing & applying acrylic synthetic 8(Eight) layers of ITF Certified (1 layer of Arcylic primer,2 layer of Acrylic resurfacer,2 layer of Acrylic Cushion,3 Layer of Arcylic colour)of approved shade and quality including cost, conveyance and taxes of all materials and cost of all labour, scaffolding, sundries and T&P etc. required for the work complete as directed by the Engineer-in-charge.

Electrical

Supply, installation, testing & commissioning of Hot dip Galvanized Octagonal poles with base plate fabricated from special steel plates as per BSEN 10025/IS 5986 and of 9 mtr length in single section being 130 mm at bottom Dia and 70 mm at top Dia and 3.0mm thickness with foundation base plate of size 200 mm x 200mm x 16mm thick Hot Dip Galvanization of both internal and external surface with minimum thickness of 86 Microns more that 600 gm/ sqm as per IS: 4759 specification. 1mtr long (Galvanized ) single arm bracket made out of 60 mm outer diameter Hot dip tubular pipes and welded to fit the top of the above pole and Plate for rigidity between cap and pipe with provision of passing the electrical cable from the pole to the end of the arm for connection of the luminaries, with provison of Electrical Termination junction in side the pole at a height of 1mtr(maximum) from the bottom of pole, with clamps, 4way 100Amps / 400Volts connector, 6/10 Amps / 230 Volts / 10KA SP MCB, Cable gland at bottom of suitable size for cable entry & exist.

Supply, installation, testing & commissioning of 240 wt LED flood lights luminaries having exclusive innovative designed, pressure die - cast aluminium housing, IP 66 proection , highlighting architectural faced & general purpose lighting with electronics driver including cost of all materials labour, T&P etc. complete as directed by the Engineer-in-charge.(Havells/ Bajaj / Phillips/ Jaquar or Equivalent)

Supplying, connection & testing of 3 c x 4 Sq. mm multicore round copper conductor etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havells / V Guard/RR/KEI )

Supplying, storing, laying, testing and commissioning of 4C x 10 Sq. mm A2XFY Aluminium armoured Cable 1100 Volts etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havels/V Guard/RR /KEI/ NICCO/Gloster/Polycab )

Supply, Testing & commissioning of 2 meter Electrode chemical earthing with 58mm G.I galvanized electrode and 25 x 3mm G.I inner strip with 50x 6mm GI connecting terminal with CPRI test certificate including cost, conveyance, loading, unloading and taxes of all materials, cost of all labour, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge.

Basket ball

Earthwork in excavation of foundation trenches in ordinary soil including dressing of sides and leveling the bed up to the required depth and depositing the excavated materials away from the work site with all leads and lifts, including shoring, shuttering and dewatering (if required) with cost of labour, hire & running charges of water pumps sundries & T&P required for the work complete as directed by the Engineer-in-charge.

Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge.

Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland slag cement (PSC) with 40 mm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes all materials and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per the instruction of the Engineer-in-Charge.

Providing and laying plain cement concrete of (1:2:4) in foundation bed and floors using 12 mm. Size black hard crusher broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required for the work etc complete as per the instruction of the Engineer-in-Charge.

Supply and Installation of Basket ball pole made of 6" dia pipe with 3.2 mtr projection and basketball board transparent acrylic imported 20 mm thick size 180cmx105 cm with dunking ring ,net and frame . Use of high quality branded MRF Epoxy paint complete in all respect including cost, conveyance and taxes of all materials and cost of all labour and T&P etc. required for the work complete as directed by the Engineer-in-charge.

Providing and painting two coats with synthetic enamel paint over a coat of red oxide primer of approved quality and approved shade confirmming to ISI on Wood work to give an even shade in all floors at all height including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge.

Electrical

Supply, installation, testing & commissioning of Hot dip Galvanized Octagonal poles with base plate fabricated from special steel plates as per BSEN 10025/IS 5986 and of 9 mtr length in single section being 130 mm at bottom Dia and 70 mm at top Dia and 3.0mm thickness with foundation base plate of size 200 mm x 200mm x 16mm thick Hot Dip Galvanization of both internal and external surface with minimum thickness of 86 Microns more that 600 gm/ sqm as per IS: 4759 specification. 1mtr long (Galvanized ) single arm bracket made out of 60 mm outer diameter Hot dip tubular pipes and welded to fit the top of the above pole and Plate for rigidity between cap and pipe with provision of passing the electrical cable from the pole to the end of the arm for connection of the luminaries, with provison of Electrical Termination junction in side the pole at a height of 1mtr(maximum) from the bottom of pole, with clamps, 4way 100Amps / 400Volts connector, 6/10 Amps / 230 Volts / 10KA SP MCB, Cable gland at bottom of suitable size for cable entry & exist.

Supply, installation, testing & commissioning of 240 wt LED flood lights luminaries having exclusive innovative designed, pressure die - cast aluminium housing, IP 66 proection , highlighting architectural faced & general purpose lighting with electronics driver including cost of all materials labour, T&P etc. complete as directed by the Engineer-in-charge.(Havells/ Bajaj / Phillips/ Jaquar or Equivalent)

Supplying, connection & testing of 3 c x 4 Sq. mm multicore round copper conductor etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havells / V Guard/RR/KEI )

Supplying, storing, laying, testing and commissioning of 4C x 10 Sq. mm A2XFY Aluminium armoured Cable 1100 Volts etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havels/V Guard/RR /KEI/ NICCO/Gloster/Polycab )

Supply, Testing & commissioning of 2 meter Electrode chemical earthing with 58mm G.I galvanized electrode and 25 x 3mm G.I inner strip with 50x 6mm GI connecting terminal with CPRI test certificate including cost, conveyance, loading, unloading and taxes of all materials, cost of all labour, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge.

Volley ball

Earthwork in excavation of foundation trenches in ordinary soil including dressing of sides and leveling the bed up to the required depth and depositing the excavated materials away from the work site with all leads and lifts, including shoring, shuttering and dewatering (if required) with cost of labour, hire & running charges of water pumps sundries & T&P required for the work complete as directed by the Engineer-in-charge.

Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge.

Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland slag cement (PSC) with 40 mm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes all materials and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per the instruction of the Engineer-in-Charge.

Providing and laying plain cement concrete of (1:2:4) in foundation bed and floors using 12 mm. Size black hard crusher broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required for the work etc complete as per the instruction of the Engineer-in-Charge.

Supply and installation of Volley Ball Pole Fixed type 3"x4" dia and Height Adjustable fix type with latest internal ratchet system with net and scaffolding including cost of all materials, labour, T&P, taxes , etc required for the work complete.

Providing and painting two coats with synthetic enamel paint over a coat of red oxide primer of approved quality and approved shade confirmming to ISI on Wood work to give an even shade in all floors at all height including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge.

providing & applying acrylic synthetic 8(Eight) layers of ITF Certified (1 layer of Arcylic primer,2 layer of Acrylic resurfacer,2 layer of Acrylic Cushion,3 Layer of Arcylic colour)of approved shade and quality including cost, conveyance and taxes of all materials and cost of all labour, scaffolding, sundries and T&P etc. required for the work complete as directed by the Engineer-in-charge.

Electrical

Supply, installation, testing & commissioning of Hot dip Galvanized Octagonal poles with base plate fabricated from special steel plates as per BSEN 10025/IS 5986 and of 9 mtr length in single section being 130 mm at bottom Dia and 70 mm at top Dia and 3.0mm thickness with foundation base plate of size 200 mm x 200mm x 16mm thick Hot Dip Galvanization of both internal and external surface with minimum thickness of 86 Microns more that 600 gm/ sqm as per IS: 4759 specification. 1mtr long (Galvanized ) single arm bracket made out of 60 mm outer diameter Hot dip tubular pipes and welded to fit the top of the above pole and Plate for rigidity between cap and pipe with provision of passing the electrical cable from the pole to the end of the arm for connection of the luminaries, with provison of Electrical Termination junction in side the pole at a height of 1mtr(maximum) from the bottom of pole, with clamps, 4way 100Amps / 400Volts connector, 6/10 Amps / 230 Volts / 10KA SP MCB, Cable gland at bottom of suitable size for cable entry & exist.

Supply, installation, testing & commissioning of 240 wt LED flood lights luminaries having exclusive innovative designed, pressure die - cast aluminium housing, IP 66 proection , highlighting architectural faced & general purpose lighting with electronics driver including cost of all materials labour, T&P etc. complete as directed by the Engineer-in-charge.(Havells/ Bajaj / Phillips/ Jaquar or Equivalent)

Supplying, connection & testing of 3 c x 4 Sq. mm multicore round copper conductor etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havells / V Guard/RR/KEI )

Supplying, storing, laying, testing and commissioning of 4C x 10 Sq. mm A2XFY Aluminium armoured Cable 1100 Volts etc. as required as per the direction of Engineer-in-Charge. ( Make of Cable - Finolex/ L&T / Anchor / Havels/V Guard/RR /KEI/ NICCO/Gloster/Polycab )

Supply, Testing & commissioning of 2 meter Electrode chemical earthing with 58mm G.I galvanized electrode and 25 x 3mm G.I inner strip with 50x 6mm GI connecting terminal with CPRI test certificate including cost, conveyance, loading, unloading and taxes of all materials, cost of all labour, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge.