Rural Development Department Tender

Providing and laying in situ cement concrete of required grade of trap / granite/ quartzite / gneiss metal for R.C.C. work in foundations like raft, grillages, strip foundations and footings of R.C.C.columns and steel stanchions including bailing out water, plywood/steel formwork, compaction, curing and roughening the surface if special finish is to be provided, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give smooth and even surface etc. complete. Spec.No: Bd.F.3/Page No.298/I.S.456 (2000)

Providing and casting in situ cement concrete of required grade of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed design and drawings or as directed, including steel centering, plywood/steel formwork, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. Including use of plastisizer wherever necessary as directed by Engineer spec.No.: Bd.F.5/Page No. 300/I.S. 456(2000)

Providing and casting in situ cement concrete of required grade of trap / granite /quartzite /gneiss metal for R.C.C. beams and lintels as per detailed design and drawings or as directed,including steel centering, plywood/steel formwork steel props, compaction, finishing uneven and honeycombed surface with C.M.1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. Including use of plastisizer wherever necessary as directed by Engineer-In-charge (Excluding reinforcement, including cover block). The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed) Spec.No.: Bd.F.6/Page No.300/I.S. 456 (2000)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.8 Page No. 302 and B.7, Page No.38

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.9 Page No. 303 and B.7, Page No.38

Providing and casting in situ cement concrete of M-15 grade of trap / granite / gneiss / quartzite metal for for coping as per detailed design and drawings or as directed including steel centring plywood/steel form work steel props compaction finishing uneven surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening them if special finish is to be provided and curing etc.complete.(Excluding reinforcement, including cover block) The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Spec. No. : Bd.E. 3/Page No. 288/I.S. 456 (2000)

Providing and fixing in position reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams and columns, canopies, staircases, newels, chajjas, lintels, pardies, coping, fins, arches etc. as per detailed design and drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required completed. Spec.No.: Bd.F.17/Page No.306

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in super structure including striking joints, racking out joints wateringand scaffolding complete. Spec.No.: Bd.G.5/Page No.315

Providing Fly ash lime Brick masonry (Bricks conforming to I.S. 12894:1990 and of size19 cm x 9 cm x 9 cm ) bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm.diameter/2 hoop iron strips 25 mm x 1.6 mm placed at every third course, properly bent and bounded at ends scaffolding, racking out joints and watering complete Spec.No.: Bd.G.7/Page No.316

Filling in plinth and floors. with contractors. approved material / murum / stone dust in 15cm. to 20cm. layers. including watering and compaction complete.( Including Royalty) Spec. No. : Bd.A. 13/Page No. 264

Providing and fixing 30mm thick PVC FLUSH L DOOR SHUTTER consisting of panel of hollow PVC profile of 20 mm thickness consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mminserted inside the hollow section of stiles rails top ?and bottom rails and two 19x 19 mm MS tubes inserted horizontally inside the hollow profile section using 4/5 mm sheet using screws hollow profile shall be lipped with 10 mm (5mm x2) thick x 20 mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof waterproof plain /prelam PVC sheet using solvent cement on the both sides of the panel including stainless steel fixtures and fastening etc. Complete as per direction of Engineer incharge, manufacturers specification and drawing.

Providing and fixing steel window of various sizes as per detailed drawing without hot dip zinc coating, without ventilators, including fabricating / glazing with plain / obscured glass panels of approved type and quality, iron oxidised fixtures and fastenings, finishing with oil painting two coats complete (with guard bars 12 mm square at 10 cm c/c.)BD-T-53 Page No. 509

Providing and fixing mild steel grill work for windows, ventilators, etc. 15 kg/sqm as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Providing internal cement plaster 12 mm thick in a single coat in cement mortar 1:4 to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B.Masonry and concrete members complete. [2/BDL/2B,P NO-36] Spec.No.: Bd.L.2/Page No.368

Providing internal cement plaster 20mm thick in a single coat in cement mortar 1:4 without neeru finish to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. Spec.No.: Bd.L.4/Page No.368

Providing and laying cement concrete flooring 40 mm thick with M15 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30 cm x 30 cm or other size laid diagonally /square etc finishing smooth (with extra cement) in any colour as directed and curing etc. complete. With Natural Sand Spec.No.: Bd.M.7 Page No. 383

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No. : As directed by Engineer-in-charge.

Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (excluding the primer coat)etc. complete. Spec. No. : Bd.P.6 Page No. 414

Providing and applying two coats of lead/zinc base oil paint/ bituminious paint of approved colour to new structural steel work and iron work in buildings including scaffolding if necessary, cleaning and preparing the surface etc. complete. (excluding primer coat). Spec. No. :Bd.0.3 Page No. 404

Providing and constructing Brick Masonry Inspection Chamber 60 cm x 45 cm x 60 cm including 1:4:8 cement concrete foundation, 1:2:4 cement concrete channels, Brick Masonry, plastering from inside and air- tight R.C.C. lid with frame fixed in cement concrete, curing, testing etc. complete. ii) WIth Reinforced cement concrete raft in B.C. soil area including cost of reinforcement Spec.No.: Bd.V.43/Page No.574

Providing soak pit of size 120 cm x 120 cm x 120 cm including excavating and filling with brick bats as per drawing etc. complete. Spec.No.: Bd.V.46/Page No.576

Providing and fixing Orissa type white glazed earthenware 575 mm water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. Spec. No. : As directed by Engineer-in-charge.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Spec. No. : As directed by Engineer-in-charge.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters Spec. No. : As directed by Engineer-in-charge.

Providing, laying and fixing P.V.C. pipe of 15mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No. : As directed by Engineer-in-charge. 15 mm Dia

32 mm Dia

Providing and fixing push cock (Self closing tap) symet type of 15 mm dia. including necessary socket, testing etc. complete. Spec. No. : As directed by Engineer-in-charge.

Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete. Spec. No. : Bd.V.9 Page No. 555

Providing and fixing 10 cm Rigid PVC Nahani Trap including PVC grating, bend, connecting piece of P.V.C.pipe of required diameter, pipe up to the outside face of the wall, making good the holes and repairs, testing etc. complete. Spec.No.: As directed by Engineer- in-charge

Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .Spec.No.: As directed by Engineer- in-charge

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring Spec.No.:Bd.M. 12 Page No.385

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.b) Skirting Spec.No.:Bd.M. 12 Page No.385

Providing and fixing 30mm thick SOLID PANEL PVC INTERNAL DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 40mm x 20mm for stiles ,top, lock and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat molded PVC channel of size 30 x 100mm forming stiles, and 5mm thick, 125mm wide PVC sheets for top rail, lock rail and bottom rail on either side, and 15mm (5mm x 3) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 10 mm thick prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the C Channel using PVC solvent cement adhesive. including stainless steel fixtures and fastening Complete as per direction of Engineerincharge,manufacturer'sspecification and drawing. Spec.No.:As directed by Engineer in charge.

The charges towards quality control tests are on the basis of testing frequency and charges fixed by Vigilance & Quality Control Circle, Nagpur for the current year.

ROYALTY CHARGES AS PER GOVT CIRCULAR . (As per Government of Maharashtra, Revenue and Forest Departments Gazette No. 67 Dt. 15 May 2015, States that the Royalty charges of Rs. 400/- Per Brass (i.e. Rs.141.34 /cum.) are to be considered.)