Directorate Of Municipal Administration Tender

Construction of granular sub-base by Plant Mix Method by providing close graded Material,mixing in a mechanical mix plant at OMC,carriage of mixed Material to work site,spreading in uniform layers with Motor Grader/ Paver on prepared surface and compacting with vibratory power roller to achieve the desired density complete as per clause 401.For Grading I Material.S.S.R.2022-23 Item No. 3.01R.A.No.4

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base /base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Laying By Grader/Paver.S.S.R.2022-23 Item No. 3.23R.A.No.5

Providing and applying primer coat with bitumen emulsion on prepared surface of Granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/Square Metre using mechanical means. S.S.R.2022-23 Item No. 3.29R.A.No.6

Providing and applying tack coat on the prepared surface heating by flames in boiler and spraying bitumen set footed in bitumen boiler on B.T. surface at 2.50 Kg per 10 Square Metre using VG-30 grade bulk bitumen. S.S.R.2022-23 Item No. 3.30R.A.No.7

Proving and laying bituminous macadam using crushed aggregates of Grading 1, premixed with bituminous binder, transported to site with Vehicle Tracking System, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired compaction for 80/100 mm compacted thickness with 3.3% VG-30 Bitumen using Batch mix type hot mix plant with SCADA, Sensor Paver, vibratory roller.S.S.R.2022-23 Item No. R.A.No.8

Providing and laying Bituminious Concrete using crushed aggregate of grading 1, premixed with bituminious binder of dose 5.40 percent by weight of total mix and filler, transported at site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired density for 50 mm compacted thickness with Drum Mix type hot mix plant with SCADA, Sensor Paver and Vibratory Roller excluding prime/Tack coat etc. complete with Bitumen VG-30 grade with stone dust filler.S.S.R.2022-23 Item No. 3.50R.A.No.9

Supplying hard murum at the road site including conveying and stacking complete. S.S.R.2022-23 Item No. 2.29aR.A.No.10

Spreading hard murum/ soft murum/ gravel or kankar for side width complete.S.S.R.2022-23 Item No. 2.30R.A.No.11

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering complete.S.S.R.2022-23 Item No. 2.31R.A.No.12

Providing and laying Cast in situ/ Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand V.S.I. Grade). S.S.R.2022-23 Item No. 24.01R.A.No.13

Providing and laying in situ/ Ready Mix cement concrete M-20 of trap/ granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying/ pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided, (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Crushed sand V.S.I. Grade). S.S.R.2022-23 Item No. 25.11R.A.No.14

Providing and laying Cast in situ/ Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Crushed sand V.S.I. Grade).S.S.R.2022-23 Item No. 26.17R.A.No.15

Providing and laying Cast in situ/ Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Crushed sand V.S.I. Grade). S.S.R.2022-23 Item No. 25.70R.A.No.16

Providing and fixing in position TMT FE -500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules, including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.S.S.R.2022-23 Item No. 26.33R.A.No.17

Providing and applying two coats (exterior quality) of flat oil paint of approved colour and shade to the plastered surface in buildings and workshops including scaffolding if necessary, cleaning the surface and preparing surface etc. complete. (excluding primer coat). S.S.R.2022-23 Item No. 35.11R.A.No.18

Providing and laying cement concrete pipe of I.S. 458:2003 non pressure-2 class of 450 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete. S.S.R.2022-23 Item No. 11.08R.A.No.19

Providing and laying Cast in situ/ Ready Mix cement concrete in M-15 of trap/ granite/ quartzite/ gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/ steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand V.S.I. Grade).S.S.R.2022-23 Item No. 24.08R.A.No.20

Providing and fixing heavy duty inter locking concrete Gray paving blocks of 60 mm. thickness of having a strength of 300 kg/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm. thick including skirting joints and cleaning etc. complete.S.S.R.2022-23 Item No. 33.49R.A.No.21

Providing and laying of hot applied thermoplastic compound 2.50 milimetre thick including reflectorizing glass beads at 250 grams per square metre area, thickness of 2.50 milimetre is exclusive of surface applied glass beads as per Indian Road Congress:35. The finished surface to be level, uniform and free from streaks and holes complete.S.S.R.2022-23 Item No. 6.12aR.A.No.22

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter (as per IRC:86-1983) embedded 125 mm below ground level over M-10 P.C.C. finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff anywhere in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant.S.S.R.2022-23 Item No. 7.01R.A.No.23

Providing and fixing Mandatory/Regulatory sign boards in circular shape of 600 mm dia made out of 1.5mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.45 m long, duly painted with with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.S.S.R.2022-23 Item No. 6.27aR.A.No.24

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 600 mm made out of 1.5mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.45 m long, duly painted with with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.S.S.R.2022-23 Item No. 6.29aR.A.No.25

Providing and fixing Cautionary/Warning sign boards in Octagone size of 750 mm made out of 2mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.45 m long, duly painted with with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.S.S.R.2022-23 Item No. 6.31aR.A.No.26

Providing and fixing of retro-reflectorised informatory sign board Rectangular/ Square in shape having area less than 0.9 square metre made out of 2 mm. aluminum sheet bonded with white retro reflective sheeting bonded with white retro reflective sheeting of Class B (Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/ heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012, Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one number of M.S. angle iron post of size 75 mm. X 75 mm. X 6 mm., 3.5 m. long, firmly fixed to the ground by means of properly designed foundation with M-25 grade cement concrete 45 cm. x 45 cm. x 60 cm., 60 cm. below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paint having alternate black and white bands of 25 cm. width including G.I. fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B (Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/ convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/ supplier.S.S.R.2022-23 Item No. 6.33aR.A.No.27