Department Of Atomic Energy Tender

Fabricating & Installation of Structural members as follows: The seat and back of arrangement should be made up of 1.5 cm thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam together with moulded back spine cover with ergonomic design for necessary adjustments. It should have a permanent contact mechanism with 360 degrees of revolution. The armrest should be made of black integral skin polyurethane and reinforced with MS insert. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. High Back Seating.

(b) Paneling on One visible side only.

Accounts Block, JCFA office, Admin & AO-III block and RPP

providing and fixing 600mmx600mm square panel 36Watts LED light units complete with plug/sockets etc including necessary power points as instructed by E-I-C

Fabricating &Installation of L-shaped work platforms of size as: top will be 1800mm (width 1) x 1200mm (width 2) x750mm (D) made from 18mm thick Ply + 1mm thick laminated sheet on exposed side and balancing white on the other side. The work surface top area will be 25 sq.ft.2 nos. fixed pedestals of size 400mm(w) x 550mm (D) to be provided on either side corners. The fixed pedestals will have one drawer (150mm ht.) on channels and cupboard with shelf.

Administration block & AO-III Office

Fabricating & Installation of Structural members as follows: The seat and back of arrangement should be made up of 1.2 cm thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam together with moulded back spine cover. It should have a permanent contact mechanism with 360 degree of revolution. The armrest should be made of black integral skin polyurethane and reinforced with MS insert. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. The 50 mm diameter twin wheel castors should be injection moulded in black nylon. Staffseatings

Labour rate only for fixing aluminium partitions/glass/plywood/plain acrylic sheet in level and line in Window/Partitions/Ceiling etc. with PVC lining gasket complete all as directed. Note : Aluminium sections/Glass/Plywood/AC sheet will be supplied by department free of cost and PVC Gasket to be arranged by contractor.

Supplying and fixing 2-Seater work stations of 48mm thick partition of 1500mm ht. made only on front side of work station Work station work station top will be 2400mmx600mm x 750mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side . Partition to be made from 9mm thick board.2 nos. fixed pedestal of size 400mm(w) x 550mm(D) to be provided on either side corners. The fixed pedestal will have one Drawer (150mm ht.) on channels , and one cupboard (575mm) with shelf

Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge.(Refer drawing no. 5)

RPP, Vashi Conference room

Dismantling existing partition, design, manufacture, install and guarantee of full height physical barrier having framework of 100 x 45 x 14 g colour anodized extruded sections. All the layers to be 12 mm BSL Particle board.

Undertaking the works of providing and fixing complete electrical works including pdg. At least 4 Plugs/sockets/switches per work station with concealed and safe way cabling etc. The work includes pdg. 8 way distribution board, 1.5mm FLRS colour coded wires etc. This also includes supply and installation of items mentioned in the Annexure - A of scope for Telephone, Fire alarm and LAN/internet cable as specified

Providing & fixing Floor Mounted Cabinets of Size 1200mm (W)x1800mm(ht)x450mm(deep) made from 18mm thick fire proof , smoke proof, termite proof ply and 1mm thick laminated sheet on exposed side and balancing white on other side. The rear side of cabinet will be9mm fire proof, smoke proof, termite proof ply. 2 nos. cabinet door shutters to be made from 18mm thick ply. All brass fittings like hinges, handles, ball catches etc as approved by Engineer-in-charge.

Supplying and fixing SINGLE-Seater work stations of 48mm thick partition of 1500mm ht. made only on front side of work station Work station work station top will be 1200mmx600mm x 750mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side . Partition to be made from 9mm thick board.2 nos. fixed pedestal of size 400mm(w) x 550mm(D) to be provided on either side corners. The fixed pedestal will have one Drawer (150mm ht.) on channels, and one cupboard (575mm) with shelf

providing and fixing 600 mmx600 mm square panel 36Watts LED light units complete with plug/sockets etc including necessary power points as instructed by E-I-C

Providing and fixing 2mm thick homogenous PVC sheet in roll form in flooring and skirting of approved make and in approved manner on damp proof smooth base using rubber based adhesive of approved quality including levelling the small undulations with plaster of Paris / white cement if required including smoothening with light roller of 5Kg. All inclusive of accessories and as directed by Engineer-in-charge (Accounts block- 830 Sq. ft., JCFA- 220 Sq. ft., Admin & AO-III block - 320 Sq. ft., RPP- 475)

Fabricating & Installation of Structural members as follows: The seat and back of arrangement should be made up of 1.2 cm thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam together with moulded back spine cover. It should have a permanent contact mechanism with 360 degree of revolution. The armrest should be made of black integral skin polyurethane and reinforced with MS insert. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. Seat Size : 460 (W) x 490 (D) mm, Back size: 430 (W) x 460 (H) mm

Supplying and fixing Aluminium framed partitions made from 63x38x1.6mm thick partition sections with built-in groove for housing 5mm thick. Glass/ 4mm thickACP panels, complete with all standard accessories, including providing one number door shutter with overhead door closer and locking arrangement, complete as per instructions of Engineer-in-charge

JC (F&A) Office

Fabricating & installation of computer work platforms of size as :top will be 1200mm x 600mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side

Undertaking the works of providing & fixing Wall Paneling, of 4mm thickness of approved make and shade Aluminium Composite Metal Panel of approved make with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethylene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification . The ACM panels have to be fixed on a frame work of Aluminium Rectangular Sections of size 50mmx25mmx1.6mm thick. spaced at 600mm C to C in true line and level. All inclusive of accessories and as directed by Engineer-in-charge. (Accounts block-1200 Sq. ft., JCFA- 480 Sq. ft., Admin & AO-III block - 2320 Sq. ft.) (Refer drawing nos. 1 to 4)

Dismantling existing partition, design, manufacture, install and guarantee of full height physical barrier having framework of 100 x 45 x 14 g colour anodized extruded sections. Thetop 2 layers to have 8 mm Deco grill 100 design duly anodized. The 3rd layer from top to be 5 mm thick clear toughened glass and bottom layer to be 12 mm BSL Particle board.

Accounts Block

Fabricating & Installation of Structural members as follows: The seat and back of arrangement should be made up of 1.2 cm thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam together with moulded back spine cover. It should have a permanent contact mechanism with 360 degrees of revolution. The armrest should be made of black integral skin polyurethane and reinforced with MS insert. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon.Mid Back Seating

Fabricating & Installation of Structural members as follows: The seat and back of arrangement should be made up of 1.2 cm thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam together with moulded back spine cover. It should have a permanent contact mechanism with 360 degree of revolution. The armrest should be made of black integral skin polyurethane and reinforced with MS insert. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. The 50 mm diameter twin wheel castors should be injection moulded in black Nylon. Seat Size : 480 (W) x 510 (D) mm, Back size: 480 (W) x 580 (H) mm

Fabricating & installation of L-shaped work platforms of size as :top will be 1800mm(width1) x 1200mm (width2) x 750mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side .The work surface top area will be 21 Sq.Ft. 2 nos. fixed pedestal of size 400mm(w) x 550mm(D) to be provided on either side corners. The fixed pedestal will have one Drawer(150mm ht.) on channels , and one cupboard (575mm) with shelf. Providing & laying glass work station top of 6mm thickness with edge polished.

providing and fixing 600mmx600mm square panel 36Watts LED light units complete with plug/sockets etc including necessary power points as instructed by E-I-C

Dismantling doors, windows and clear storey windows (steel / wood) shutter including chow khats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area beyond 3.00 Sq.M

Providing fabricating & fixing in-situ made cupboard with 3nos. Shelves and door shutter of plain transparentglass 6mm thick

Fabricating & fixing of structural members as follows: The seat and back arrangement should be made up of 12mm thick hot pressed plywood measured and upholsteredwith fabric upholstery covers and moulded polyurethane foam together with moulded back spine cover .It should have permanent contact mechanismwith 360 degree of revolution.The armrest should be made of black integralskin polyurethane and reinforced with M S inserts. The 50mm diameter twin wheel castors should be injection moulded in black nylon.Seat size : 460mm(W) x 490 mm(D)

Fabricating &installation of L-shaped work platforms of size as :top will be 1800mm(width1) x 1200mm (width2) x 750mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side .The work surface top area will be 21 Sq.Ft. 2 nos. fixed pedestal of size 400mm(w) x 550mm(D) to be provided on either side corners. The fixed pedestal will have one Drawer(150mm ht.) on channels , and one cupboard (575mm) with shelf. Providing & laying glass work station top of 6mm thickness with edge polished.

Providing & fixing Floor Mounted Cabinets of Size 1800mm (W)x1200mm(ht)x450mm(deep) made from 18mm thick fire proof, smoke proof, termite proof ply and 1mm thick laminated sheet on exposed side and balancing white on other side. The rear side of cabinet will be9mm fire proof, smoke proof, termite proof ply. 2 nos. cabinet door shutters to be made from 18mm thick ply. All brass fittings like hinges, handles, ball catches etc as approved by Engineer-in-charge

Providing fabricating & installing a 12mm thick toughened glass view window of siz 10'(W) x 4'(ht.)

Aluminium partition works at RPP, Vashi

Providing and fixing Lay in False Ceiling 600 x 600mm unperforated corrosion resistant aluminium magnesium alloy metal panel fixed in 24 mm 'T' Frame work of Module 600 x 600 mm. Panels shall be of size 575 mm x 575 mm of approved colour in 0.70 mm thick Aluminium Alloy 3105 with square edges Tiles to be stove enameled on a continuous application for pre-treatment. The coils to be go through 4 stages of pre treatment Three times of oven baked through conversion coating, priming and finish coat ensuring superior adhesion, high corrosion resistance and good colour stability. The coils to be painted on both sides after degreasing. Inside surface to have a primer of 5 microns and a coat of natural colour of 5 microns, exposed surface to have a primer of 5 microns, binder of 5 microns and a topcoat of approved colour 15 microns. Grid system for fixing ceiling tiles shall comprise of tees. The 24 mm main tee runners shall be suspended at an interval of 1200 mm centre to centre. The 24 mm cross tee runner shall be suspended at an interval of 600 mm centre to centre and further supported with 24 mm cross tee with inter locking arrangements to form a Grid of 600 mm x 600 mm. The main tee shall be supported by means of 4 mm G.I. rod from slab / roof. The suspension shall be provided at 1200 to 1500 mm centre to Centre. Provision for lights, diffusers etc to be made including extra supports wherever necessary. Measurements shall be as per actual area of false ceiling with out deductions for lights and diffusers. Accounts block- 830 Sq. ft., JCFA- 220 Sq. ft., Admin & AO-II block - 1400 Sq. ft., RPP- 475)

Fabricating & installation of computer work platforms of size as :top will be 1200mm x 600mm (D) made from 18mm thick marine ply+1mm thick Laminated sheet on exposed side and balancing white on other side .The work surface top area will be 8 Sq.Ft. 1 nos. fixed pedestal of size 400mm(w) x 550mm(D) to be provided on any side corner. The fixed pedestal will have one Drawer(150mm ht.) on channels , and one cupboard (575mm) with shelf.

Providing, fabricating & fixing in place paneling of Aluminium Composite Panels 4mm thick/combination of 3mm/ 4mm thick ply board and lamination/veneer to match the paneling on existing cabin as follows: (a) Paneling on both sides of structure

Installation of Ceiling Suspended EnergyEfficient LED lights 36Watts, 600mmx600mm Panel light fixtures Including the necessary conduits, flexible pipes, ceiling roses, 1.5 mm Wires, Switches, switch boxes etc. complete as directed byEngineer-in-Charge.