Central Institute For Cotton Research Tender

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm ncluding grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Double charge vitrified tile polished finish of Size of Tile 600 x 600 mm

12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre : Two coat

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing 12 mm thick frameless toughened glass of approved brand and manufacture, including providing and fixing top & bottom pivot and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid: JAQUAR as approved by Engineer - in - charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting (15 mm nominal dia Pipes)

20 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab colour of Black,Cherry/Ruby Red or equivalent

Cabin Table_(2400×H750×D991) Providing & fixing in position with Table made up of 1.Top panel in 36 (18mm+ 7.5mm+5.5mm HDHMR + 6mm BPG GLASS) mm thick. HDHMR white matt finished with Edge Profile from all sides with 6mm back painted glass. 2. Modesty panel in 18mm thick. HDHMR Matt Finished both side laminated with pve edge binding machine pressed from all sides. 3.Base Support CRCA Pipe frame 25x75x1.2mm Powder Coated. including necessary hardware etc. as per approved shade & colour.As directed by Engineer in charge.

Side Credenza (3 Top Drawers & 3 Base Shutter)_(w2000h750×d450) Providing & fixing in position with Side Credenza made up of 1. Top Panel in 25mm thick. MDF front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides. 2. Shutter & Drawer Facia in 18mm thick. HDHMR front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides. 3. Carcase & Drawer material in 18mm thick. HDHMR white both side white matt finished with pvc edge binding machine pressed from all sides. including necessary Regular Hinges , Regular Telescopic Rail, Pocket Handle etc complete as per approved shade & colour. As directed by Engineer in charge.

Corner Back Credenza (1 Base Shutter)_(w1600h750d450) Providing & fixing in position with Credenza made up of 1. Top Panel in 25mm thick. MDF front side Matt Finished & backing plain white matt finished with pve edge binding machine pressed from all sides. 2. Shutter in 18mm thick. HDHMR front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides. 3. Carcase in 18mm thick. HDHMR white both side white matt finished with pvc edge binding machine pressed from all sides. including necessary Regular Hinges, Pocket Handle etc complete as per approved shade & colour. As directed by Engineer in charge. As directed by Engineer in charge.As directed by Engineer in charge.

Back Credenza (2 Base Shutter)_(w1450h750d450) Providing & fixing in position with Credenza made up of 1. Top Panel in 25mm thick. MDF front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides. 2. Shutter in 18mm thick. HDHMR front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides.3. Carcase in 18mm thick. HDHMR white both side white matt finished with pvc edge binding machine pressed from all sides.including necessary Regular Hinges, Pocket Handle etc complete as per approved shade & colour. As directed by Engineer in charge.

Tall Shelf Storage Unit (6 Base Drawers & 2 Top Shutters) _ (w1200×h3000×600) Providing & fixing in position with Storage made up of 1. Shutter & Drawer Facia in 18mm thick. HDHMR front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides. 2. Carcase & Drawer material in 18mm thick. HDHMR white both side white matt finished with pvc edge binding machine pressed from all sides. including necessary Regular Hinges, Regular Telescopic Rail, Horizontal Gola Handle etc complete as per approved shade & colour. As directed by Engineer in charge.

Conference Table_(2700×H750×D1500) Providing & Fixing in position with Conference Table made up of 1. Top Panel in 25mm thick. MD front side Matt Finished & backing plain white matt finished with pvc edge binding machine pressed from all sides.2. Base Support CRCA Sure Pipe Frame 25x75x1.6mm Black Powder Coated. with necessary Hardware Modular Flap etc. as per approved shade & colour. As directed by Engineer in charge.

Providing & Arrangemnt of High Boss Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. As directed by Engineer in charge.

Sofa Set 3 Seater Providing & fixing Sofa Set 3 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: 3 Seat As directed by Engineer in charge.

Tea Table 1000mm X 850mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 1000mm X 850mm X 450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc. As directed by Engineer in charge.

Providing & Arrangemnt of Mid Back, ECO CTS Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery

Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade-I MDF Board 12 mm thick confirming to IS:14587

Providing and fixing Electrical Work Including Switches, lights, Wirings, Pedestrial Fan, Power Switches and etc as approved by Engineer - in - charge. (as per Electrical drawing)