Urban Administration And Development Tender

FIRE PANEL- Providing fixing and testing and commissioning Micro processor based Main Fire Panel and indicating Panel solid state modular card PULSAR, DUAL Stage Alarm Facility with indicator, alarm facility with indicator, standby battery, complies to IS 2189 : 1999.2 x 16 character backlit LCD display lamp test features complete with integral power supply and battery charger for SMF battery NO/NC contact for both fire and fault Switches to enable on board operation LCD and LED indication for open short circuit isolate fire in each zone Reset Lamp test silence Isolate short open fire continous buzzer for fault and intermitted buzzer for fire battery charger box, operationg oltage 220 volt main A.C nput 24V D.C output etc. complete in all respect. 8 zone panel

Fabricating & Supply, installing, testing and commissioning of compartmentalized common control panel for Electrical motor driven umps and Diesel engine driven pump & Jockey Pump. INCOMING 1 nos. 250 A TPN MCCB (50 KA) 1 Sets of 300 Amps. TPN Al. Bus bars with colour coded heat shrinkable PVC sleeves. 1 Set of RYB indicating lamps with individual HRC control fuses. 1 No. 96 Sq.mm 0-800 Amps. Ammeter with selector switch and suitable rated current transformers. 1 No. 0-800 96 Sq.mm Voltmeter with selector switch. OUTGOING Feeder for main pumps - 1 Nos. 1 Nos.160 A TP MCCB Star delta starter with over load relay, single phase preventor and indicating lamps with ON / OFF push buttons. Feeder for Jockey pump - 1 No. 1 No. 40 A TP MCCB DOL starter with over load relay, single phase preventor and indicating lamps with ON / OFF push buttons. 2 No. Auto manual selector switch DIESEL ENGINE MAIN PUMP 1 No. a) 20Amps DPMCB - 4 Nos. b) Battery charger with transformer with rectifier resistance DC ammeter, DC voltmeter, Trickle / booster / off selector switch - 2 Nos. c) 1 set of indicating lamps for the following 1. phase indication, 2. battery charger on, 3. over load relay, 4.DC supply on, 5. control switch on, 6. Engine fails to start, 7. Pump on, 8. Low oil pressure, 9. High water temperature, 10. Auto manual selector switch, d) 1 sets of push button stations for the following : 1. Engine Start, 2. Engine Stop, 3. Engine - hooter ACK, 4. Engine - fault reset, e) Selector switches (Engine control, mode selector)-1 No. f) Auxiliary relays / contactors / timer for sequence operating for starting and stopping of the engine - 1 set…....

Providing, fixing, testing and commissioning of butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets,confirming to IS 13095, of following sizes as required. 100mm dia....

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket confimimg to IS: 15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 4.5 Kg....

Providing and fixing flow switches in 100/150 mm dia MS pipe....

Providing and fixing angle iron (40 mm x 40 mm x 5 mm) door frame and M.S sheet (2 mm thick) cum glass shutter of size 1.2 mtr x 2.1 mtr (N.S.) with 25 mm x 25 mm x 3 mmangle frame all around & stiffened in between including hinges, handle, locking arrangement, painting with approved synthetic enamel paint

Internal hooter: Providing &fixing of internal hooter with working AC Voltage 220V A.C./24V D.C. current consumption, sound output 120 DB, material M.S. sheet.

Supplying, installation, testing & commissioning of approved make jockey pump horizontally mounted coupled motor (Eff-2) 5.5hp, 2900 RPM, 3 Ph 415 V with mechanical seal pump, delivery of 180 litres per minute against total head of 70 / 88 meter so as to ensure a minimum pressure of 3.5 Kg/Cm2 at the highest. The impeller shall be closed type and accurately balanced dynamically. The pump shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. i/c coupling, coupling guard,base channel foundation & matching flanges etc.as required as per specifications....

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 100mm dia

Supplying and fixing 2 way fire brigade connection of cast iron body with 4 nos. gun metal male instantaneous inlet couplings complete with cap and chain as required. For 150mm dia MS pipe connection, confirming to IS 904 as required.

Manual call point: Providing & fixing of manual calls point flush or surface mounting. Front protection glass cover. Unbreakable glass ABS plastic body....

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 100mm dia

Supply,installation,testing,commissioning,putting into opertion and final testing of automatic lift complte in the shaft well and pit constructed (ARD),All standard equipments,accessories and control equipments as per manufacturer's design and as per CPWD specification (part III LIFTS) ON turn key basis ,conforming to NBC/STatutory norms and fulfilling following requirements. (make; schindler,mistsubishi,otis,orbis,johnson,Thyssen kruup) (i) Type;Passenger lift (ii) load;as specified elsewhere from 4 passenger (272kg) to 26 passenger (1768kg) (for each person standard weight 68 kg) (iii)speed;1.00 Meter/sec (iv)control;ACV3F,32bit Microprocessor integrated serial communication control sytem with RMS (Remote momitoring system) /BMS Supporting software (v) Motor/machine;permanent magnetic synchronous gearless motor (vi) opertion; simple colletive selective with /without lift attendant (vii) Total rise ;about 3 mtrs (Approx) two stop only (viii) Landings; All flors on same side (ix) Floors served; G +1 (x) Singnals;Digital car position indicator, car travel direction indicator inside car & at all landings, voice annunciator with suitable music shall be provide in the lift car (xi) Shaft size;as per manufacturer,s design and as per CPWD specification (part III LIFTS) Shaft to be constructed separately (xii) Guide rail; As per manufacturer,s specification (xiii) Lift & car size ;as per manufacture design and as per cpwd specification (part III lifts) (xiv) Car entrance ;as per manufacture's design and as per CPWD specification (part III LIFTS) (xv) Landing entrance ; as per manufacture;s design and as per CPWD speci (xvi) Car door : S.S. (Stainless steel) hairline finish centre / Telescopic opening door with vision panel. (xvii) Landing door : S.S. (Stainless steel) Hairline finish centre / Telescopic opening door with vision panel. (xviii) Door operation : Automatic electric power operated door, Full height infra red curtain with multiple criss/cross light beams (xix)Car interior : S.S. (Stainless steel) panel with hair line finish on all sides. (xx)Car floor : Anti skid PVC flooring on heavy duty M S (Mild Steel) platform (xxi)Car ceiling & lighting : S. S. (Stainless steel) finishes with aesthetic appearance with LED ceiling lights (xxii Car ventilation : Pressure fan / Blower fan (Car fan with automatic sleep timer shall be provided). (xxiii) Emergency lighting in car : Battery operated emergency lighting in the lift car (xxiv) Intercom system : Battery operated Intercom system in lift car, machine room and ground floor/control room. (xxv) Emergency alarm : Battery operated alarm bell system in lift car & control room/ Ground floor. (xxvi) Position of machine room : Directly above the hoist-way. (xxxii) mechanical over speed governor, door key holes in the floor doors shall be provided (xxxiii) Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the lift agency, along with the other steel structure works, foundations for the machines etc.. (xxxiv) In the hoist way fascia plate shall be provided (xxxv) Permanent wiring in lift machine room and lift well with proper no. of light points, with fixtures, exhaust fan, plug points and 3 phase 440V power supply shall be made available by the department in lift shaft, machine room or at desired level. (xxxvi) Car top safety barricade shall be provided. (xxxvii) ARD (Automatic rescue device) : Solid state inbuilt automatic rescue device (ARD) for automatically rescues passengers trapped in the lift car in between floors in the event of power failure. Automatic operation and immediate action in the event of mains failure capable to move the lift to the nearest landing, opens the automatic door of the lift car and floor. Sealed maintenance free battery backup with automatic charging unit and auto changeover device on mains failure. (c) Add extra for every additional floor beyond initial G+1 floors (additional (i) stops beyond two stops) provide all necessary additional parts/ equipments as per manufacturer's requirement. Cost for each additional floor : upto 9 stops (For 4-10 Passengers

Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm. in height with air release valve on top and flanged connection ser, drain arrangement with 25mm dia gun metal wheel valve, with equired accessories, pressure gauge and painting with synthetic enamel paint of approved shape as required.

Providing, fixing, testing and commissioning of butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets,confirming to IS 13095, of following sizes as required. 150mm dia....

providing and fixing double headed hydrant valve with instantaneous female Gun metal couplings of required dia. with cast iron wheel ISI marked conforming to IS 5290 (Type- A) with blank gunmetal cap and chain, a adopter as required complete as directed by Engineer-in Charge. 63mm dia

Supplying and fixing first -Aid hose reel with MS construction spray painted in post office red, confirming to IS 884 with upto date amendments, complete with the following as required. a) 30/36m long 20mm (nominal internal dia) water h27e thermoplastic (textile reinfirced ) type -2 as per IS 12585 b) 20mm (nominal internal) dia gun metal globe valve and nozzle. c) Drum and brakets for fixing the equipments on wall. d) Connections from riser with 40 mm dia stop valve (gun metal ) and M.S. pipe....

Suppy, installation, testing & commissitioning and putting into operation and final testing of automatic lift complete with ARD and all standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) and fulfilling following requirments on turn key basis. (i) Type;Passenger lift (ii) load;as specified elsewhere from 4 passenger (272kg) to 26 passenger (1768kg) (for each person standard weight 68 kg) (iii)speed;1.00 Meter/sec (iv)control;ACV3F,32bit Microprocessor integrated serial communication control sytem with RMS (Remote momitoring system) /BMS Supporting software (v) Motor/machine;permanent magnetic synchronous gearless motor (vi) opertion; simple colletive selective with /without lift attendant (vii) Total rise ;about 3 mtrs (Approx) two stop only (viii) Landings; All flors on same side (ix) Floors served; G +1 (x) Singnals;Digital car position indicator, car travel direction indicator inside car & at all landings, voice annunciator with suitable music shall be provide in the lift car (xi) Shaft size;as per manufacturer,s design and as per CPWD specification (part III LIFTS) Shaft to be constructed separately (xii) Guide rail; As per manufacturer,s specification (xiii) Lift & car size ;as per manufacture design and as per cpwd specification (part III lifts) (xiv) Car entrance ;as per manufacture's design and as per CPWD specification (part III LIFTS) (xv) Landing entrance ; as per manufacture;s design and as per CPWD speci (xvi) Car door : S.S. (Stainless steel) hairline finish centre / Telescopic opening door with vision panel. (xvii) Landing door : S.S. (Stainless steel) Hairline finish centre / Telescopic opening door with vision panel. (xviii) Door operation : Automatic electric power operated door, Full height infra red curtain with multiple criss/cross light beams (xix)Car interior : S.S. (Stainless steel) panel with hair line finish on all sides. (xx)Car floor : Anti skid PVC flooring on heavy duty M S (Mild Steel) platform (xxi)Car ceiling & lighting : S. S. (Stainless steel) finishes with aesthetic appearance with LED ceiling lights (xxii Car ventilation : Pressure fan / Blower fan (Car fan with automatic sleep timer shall be provided). (xxiii) Emergency lighting in car : Battery operated emergency lighting in the lift car (xxiv) Intercom system : Battery operated Intercom system in lift car, machine room and ground floor/control room. (xxv) Emergency alarm : Battery operated alarm bell system in lift car & control room/ Ground floor. (xxvi) Position of machine room : Directly above the hoist-way. (xxxii) mechanical over speed governor, door key holes in the floor doors shall be provided (xxxiii) Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the lift agency, along with the other steel structure works, foundations for the machines etc.. (xxxiv) In the hoist way fascia plate shall be provided (xxxv) Permanent wiring in lift machine room and lift well with proper no. of light points, with fixtures, exhaust fan, plug points and 3 phase 440V power supply shall be made available by the department in lift shaft, machine room or at desired level. (xxxvi) Car top safety barricade shall be provided. (xxxvii) ARD (Automatic rescue device) : Solid state inbuilt automatic rescue device (ARD) for automatically rescues passengers trapped in the lift car in between floors in the event of power failure. Automatic operation and immediate action in the event of mains failure capable to move the lift to the nearest landing, opens the automatic door of the lift car and floor. Sealed maintenance free battery backup with automatic charging unit and auto changeover device on mains failure. (a) Passenger capacity (iV) 6 passenger (408kg.)

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. Amendment 100mm dia....

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 80mm dia

CONSTRUCTION OF COMMERCIAL AND RESIDENTIAL COMPLEX AT THADDARAM COMMUNITY CENTRE, SANT HIRDARAM NAGAR WARD 05 ZONE 01

Providing and fixing of ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket confimimg to IS: 15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 6 Kg....

Supplying and fixing following dia, 15 mtr long RRL hose pipe with following dia male and female gun metal couplings duly binded with GI wire, rivets etc. confirming to IS 636 (type-A) as required. 63mm dia....

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 150 mm dia

Supply installation, testing and commissioning of approved make required1 fire panel for manual operated fire hooters etc. as required as per specifications but excluding pipe and connection cable.

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. Amendment 26.8 150 mm dia....

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor. 4 CORE ARMOURED 50 Sq.mm

Supply,installation,testing,commissioning,putting into opertion and final testing of automatic lift complte in the shaft well and pit constructed (ARD),All standard equipments,accessories and control equipments as per manufacturer's design and as per CPWD specification (part III LIFTS) ON turn key basis ,conforming to NBC/STatutory norms and fulfilling following requirements. (make; schindler,mistsubishi,otis,orbis,johnson,Thyssen kruup) (i) Type;Passenger lift (ii) load;as specified elsewhere from 4 passenger (272kg) to 26 passenger (1768kg) (for each person standard weight 68 kg) (iii)speed;1.00 Meter/sec (iv)control;ACV3F,32bit Microprocessor integrated serial communication control sytem with RMS (Remote momitoring system) /BMS Supporting software (v) Motor/machine;permanent magnetic synchronous gearless motor (vi) opertion; simple colletive selective with /without lift attendant (vii) Total rise ;about 3 mtrs (Approx) two stop only (viii) Landings; All flors on same side (ix) Floors served; G +1 (x) Singnals;Digital car position indicator, car travel direction indicator inside car & at all landings, voice annunciator with suitable music shall be provide in the lift car (xi) Shaft size;as per manufacturer,s design and as per CPWD specification (part III LIFTS) Shaft to be constructed separately (xii) Guide rail; As per manufacturer,s specification (xiii) Lift & car size ;as per manufacture design and as per cpwd specification (part III lifts) (xiv) Car entrance ;as per manufacture's design and as per CPWD specification (part III LIFTS) (xv) Landing entrance ; as per manufacture;s design and as per CPWD speci (xvi) Car door : S.S. (Stainless steel) hairline finish centre / Telescopic opening door with vision panel. (xvii) Landing door : S.S. (Stainless steel) Hairline finish centre / Telescopic opening door with vision panel. (xviii) Door operation : Automatic electric power operated door, Full height infra red curtain with multiple criss/cross light beams (xix)Car interior : S.S. (Stainless steel) panel with hair line finish on all sides. (xx)Car floor : Anti skid PVC flooring on heavy duty M S (Mild Steel) platform (xxi)Car ceiling & lighting : S. S. (Stainless steel) finishes with aesthetic appearance with LED ceiling lights (xxii Car ventilation : Pressure fan / Blower fan (Car fan with automatic sleep timer shall be provided). (xxiii) Emergency lighting in car : Battery operated emergency lighting in the lift car (xxiv) Intercom system : Battery operated Intercom system in lift car, machine room and ground floor/control room. (xxv) Emergency alarm : Battery operated alarm bell system in lift car & control room/ Ground floor. (xxvi) Position of machine room : Directly above the hoist-way. (xxxii) mechanical over speed governor, door key holes in the floor doors shall be provided (xxxiii) Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the lift agency, along with the other steel structure works, foundations for the machines etc.. (xxxiv) In the hoist way fascia plate shall be provided (xxxv) Permanent wiring in lift machine room and lift well with proper no. of light points, with fixtures, exhaust fan, plug points and 3 phase 440V power supply shall be made available by the department in lift shaft, machine room or at desired level. (xxxvi) Car top safety barricade shall be provided. (xxxvii) ARD (Automatic rescue device) : Solid state inbuilt automatic rescue device (ARD) for automatically rescues passengers trapped in the lift car in between floors in the event of power failure. Automatic operation and immediate action in the event of mains failure capable to move the lift to the nearest landing, opens the automatic door of the lift car and floor. Sealed maintenance free battery backup with automatic charging unit and auto changeover device on mains failure. (f) Add extra for hall lantern and arrival gong system. (i) Extra cost for per floor per lift Add extra to item no. 44.1 for hall lantern and arrival gong system

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 80mm dia

Providing and fixing 63mm gun metal branch pipe with 20mm (nominal internal diameter)size gun metal nozzle conforming to IS 903, suitable for instantaneous connection, to interconnect hose pipe coupling as required 26.15 Amendment....

Supplying and fixing hose cabinet of size 900mmx600mmx500mm made of 2 mm thick MS sheet with 4 mm thick float glass doors in front painted "FIRE" in red paint i/c necessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos. 15mtr. Long hose pipe, 1 no branch pipe mounted on wall or raised brick platform and duly painted with Post office red externally and white internally with synthetic enamel paint complete in all respects for external hydrant, as directed by Engineer-In-Charge.

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers jointing with nuts bolts, gaskets and welding etc. underground including excavation and providing cement concrete blocks as supports, at prescrived intervals and anticorrosive treatment with coal tar/asphalt tape as per IS 10221, with 4mm thick fiber renforced tape and 12mm overlap and refilling the trench etc. of following sizes complete as directed by Engineer-In-Charge. 25mm dia