Local Self Government Department Tender

5.1.1a:Prime Coat :- Low porosity <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

5.2.3a:Tack Coat <br>Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

5.2.1a:Tack Coat<br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.9.3.pa:Plastic Roads - Bitumen S-65 Plastic roads- Bulk Bitumen Rate 20mmthick Open-Graded Premix Carpet using Bituminous (penetration grade/modifiedbitumen) Binder - Bitumen S-65 - Bulk Bitumen and Shredded Plastic Providing, laying and rolling of open-graded premix carpet of 20 mm thicknesscomposed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen oremulsion to required line, grade and level to serve as wearing course on a previouslyprepared base, using HM Plant attached with open pugmilll.Heating of aggregate at 150degree Celsius to 170 degree Celsius, then transferring the hot aggregate to pugmill andadd shredded plastic @10.22 kg/100m2 mixing well to form a uniforth thin layer of plasticOver-hot aggregate and adding hot bitumen (150 to 165 degree Celsius) @ 13.578Kg/10m2 and mix well, laying and rolling with a three wheel 80-100 kN static rollercapacity, finished to required level and grades to be followed by seal coat of either TypeA or Type B or Type C as per Technical Specification Clause 508 Case - I ByManual Means (II) Bi umen (5-65),including supplying and stacking of materials.

5.12.A.3.2a:Seal Coat - Manual Means - Type C - Bitumen S-65 <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means :- Case - III : Type C <br> (II) Bitumen (S-65)

OD174811/2024-2025:Surface dressing of ground including removing vegetation and in -equalities not exceeding 15cm deep and disposal of rubbish , lead up to 50m and lift up to 1.5m All kinds of soil

75.8.1.1.A:Providing Plain cement concrete for wearing coat CC 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) Nominal mix (1:2:4)

75.8.1.1:Providing plain/reinforced concrete(1 cement:2 fine aggregate: 4 course aggregate) forsubstructure as per drawings and technical specifications Clause 802, 803, 1202 & 1203as required including compaction, finishing and tamping etc .complete. Max. size ofcourse aggregate not exceeding 25mm , mixed in concrete mixer etc complete as perspecification (i) Nominal mix (1:2:4)

OD204298/2024-2025:Supplying and fixing nameboard of size 75*60 cm size using GI pipe as post and 1 mm thick MS sheet surrounded by MS angles including painting, lettering and fixing in concrete etc as per directions of Engineer-in-charge.