Infopark Tender

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete as directed by Engineer - in-Charge

Making chases by cutting floor or wall up to 25 cm in width and 12.5 cm in depth including making good and finishing with matching surface for race way or counduits installation.

Providing and laying vitrified floor tiles of size 600x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades in skirting riser of steps over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joints with matching colour epoxy filling width upto 5mm., complete as per directions of Engineer-in-charge.

Providing and fixing at all height false ceiling conforming to IS:2095 (BS 1230) including providing and fixing of frame work made of special sections power pressed from GI sheet and galvanized in accordance with zinc coating of grade 350 as per IS:277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm dia x 40mm long with 6 mm dia bolts to the angle hangers of 25x 25x 0.55 mm of required length, and other end of angle hanger being fixed with nut and bolts to GI channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to GI channel with connecting clips made out of 2.64mm dia x230 mm long GI wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20 mm and 30 mm long, The perimeter of ceiling shall be fixed to wall / partition with the help of raw plugs at 450 mm centre to centre with 25 mm long drive-all screws @ 230 mm interval including jointing and fixing to a flush finish of tapered and square edges of the gypsum board with recommended filler, paper tapes, finisher and two coats acrylic emulsion paint over two coats of primer suitable for gypsum board as per manufacturers specification after application of E-Mix/ Pop / Gypsum putty and all as per manufacturer’s specification etc completeand all as directed.and also including the cost of making openings for light fittings, grills, diffusers, trap doors, cutouts made with frame of perimeter channels suitably fixed all complete as per directions of engineer-in-charge.

12.5 mm thick tapered edge gypsum plain board (Vertical visible areas in drop ceiling will be measured separetely)

Decorative ceiling using 12.5 mm thick gypsum plain board as per the design (Only plan area will be measured)

Providing and fixing in true horizontal level false ceiling with GI metal ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop made of GI sheet having galvanising of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyster powder coated of thickness 60 micron (minimum), including factory painted after bending and perforation, and backed with black glass fibre acoustical fleece laid in silhouette grid system with 15mm white flanges incorporating a 6mm central reveal in white/ black colour manufactured by approved supplier, using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mm x 19mm x 19mm used in periphery of the ceiling fixed to the wall partition/ RC column/ band walls with the help of screws at 600mm c/c. Main runner to be suspended from celing using GI slotted cleats of size 27x37x25x1.5 mm fixed to celing with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvasined butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm c/c along main tee and 1200mm long cross tee to be interlocked between in Main runner at 600mm c/c (max) to form a grid of 1200 x 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mm x 600mm. The rate shall be inclusive of making openings for light fittings, grills, diffusers, cutouts, wastage and necessary hardware etc. The grid tiles which are replaced by diffucers/ lights should be handed over to Infopark.

Providing and fixing 100 mm overall thickness partition with 12.5 mm thick double skin tapered edged Gypsum board conforming to IS:2095: Part 1 upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification. Air gap between the plasterboards is to be lined with 50 mm thick approved fiberglass wool and the contractor must ensure that the fiberglass wool is wire-braced to prevent it from ‘lumping down’ over a period of time. The rate shall be inclusive of providing aluminium skirting 100 mm high and 1mm thick of approved make aluminium profile with natural color andoizing fixing at bottom on both side of the partition and as per directions of Engineer in charge all complete.

Providing and fixing Partition above the false ceiling level using Aluminium box frames of size 50mmx25mmx1.5mm thickness at 610mmc/c on both direction and to be covered with 12.5 mm thick single layer Gypsum board on one side. The boards shall be fixed with counter sunk stainless steel / fully threaded self tapping screws of suitable dia and length at every 300 mm c/c. (Above all partitions) Note: The Aluminium framework shall be anchored etc. / fixed properly in true RCC ceiling and additional diagonal supports to get sufficient rigidness. Actual seen surface area will be measured and paid, if any doors, glass panels, openings are provided in this partition the area of the same shall be deducted.

Straight Glazed Partition of approved make: Supply and installation of full height straight glass partition 12mm thick toughened glass and proprietary black powder coated aluminium sections of approved make 45x25mm thick. Providing door frame section at around the door two vertical upto false ceiling and horizontal at door top. The sections shall be matt natural anodized and shall be a combination of SAP 004 and 005 on all four sides as per the manufacturers specification and shall be inclusive of all accessories like stake1, stake3 and wedge 3G/B from FFL to the bottom of false ceiling height. The glass joints shall be filled with silicon sealant / beading on both side and the vendor has to prepare the shop drawing for client / Architects approval. Rate shall include for providing transport charges, handling, loading and unloading, Installation, protecting the module and glass till handing over, testing, commissioning all necessary hardware's, scafolding,wastage, Structural supports if any, etc. complete and all as per manufacturers specifications as directed.

Providing and fixing 12 mm thick frameless toughened patch fitting glass door (area not greater than 2.5sqm) of approved brand and manufacture, including providing and fixing top & bottom pivot, corner fittings, patch fittings, floor spring with SS cover plate, lock with euro profile cylinder keys 3 nos, strike patch for lock, door stopper, pull handle SS Satin finish & for fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge. (Approximate door size : 1100 x 2100 mm or nearest)

Removing and refixing of existing glass door including fixing top and bottom pivot, corner fittings, patch fittings, floor spring with SS cover plate, lock with euro profile cylinder, strike patch for lock, door stopper, making necessary holes etc. all complete as per directions of engineeer-in-charge

Glass film : The work includes removal of existing glass film work and fixing glass film stickers of approved model and colour as per required pattern and shape and as directed.

Smooth plastering of surface for painting - providing 12 mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) finished with a floating coat of neat cement etc complete as per directions of Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Painting two or more coats with premium acrylic emulsion paint of interior grade, having VOC(Volatile Organic Compound) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour as per directions of Engineer-in-charge.

Fabrication, supply and installation at site open office type modular workstations Linear Double sided of size 1200x600x 750mm; Leg and beam desk system of following specification and size. Table top: 25 mm thick prelaminated particle board with 2mm thick PVC edge band lipping, access flap wire manager: Understructure: Made of ERW tubular structure of size 50x50mm 1.6 mm thick powder coated with suitable levelers; power beam for integrated wire management, raceways, Privacy screens :Sandwitch glass screens with 8 mm thick laminated glass of approved colour supported on brackets duly powder coated; Raceway: Two numbers vertical and horizontal for data and power with provision for sockets/data below table top.

Supplying and placing in position Medium back task mesh chairs for workstations with ergonomic design, good lumbar support, seating comfort, Seat with high density PU foam upholstered with approved quality fire retardant fabric, mesh back, Hydraulic gas lifting mechanism, Tilt locking mechanism, fixed armrest with integral PU skin metal inserted arm rests, five pronged chrome base with nylon castors.

Wall paper: Fixing to wall partition wall paper of approved colour, Design etc as per required pattern and shape and as directed.

Supply and installation of interior film on metallic door. This work includes the preparation of door surface to achieve a smooth surface for stickering

Engaging manpower for undertaking miscellanous work (muster roll and reports shall be maintained) as per direction of Engineer - in - charge: Coolie

Supplying and fixing of 4 way (4 + 12), Double door surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required .

Supplying and fixing 12 way,double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supply and installation of 40A, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and installation 25A, DP MCB in the existing VTPN DB complete with connections, testing and commissioning etc. as required.

Supply and installation 32A, TP MCB in the existing VTPN DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 25A, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and installation 40A double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required

Supply and installation Single pole, 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and installation of 20 mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supply and installation of 25 mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supply and installation of 20 mm medium class PVC flexible conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supply and installation of 25 mm medium class PVC flexible conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supply and drawing 3 X 1.5 sq.mm ISI marked FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply and drawing 3 X 2.5 sq.mm ISI marked FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply and drawing 2 X 4 sq.mm and 1 x 2.5 sq mm ISI marked FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply and drawing 2 X 6 sq. mm and 1 X 2.5 sq mm ISI marked FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing 6A Switches (3 nos) for 3 module, GI box along with modular base & cover plate for modular switches in recess etc.

Supplying and fixing 6A Switches (2 nos) for 2 module, GI box along with modular base & cover plate for modular switches in recess etc.

Supply and installation with modular plate and cover in front on surface or in recess, including providing and installation 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required in the work stations for raw power .

Supply, installation, testing and commissioning of 1 No. of 15/16A Universal (Flat type/Round type ) 6 Pin Raw Power Socket and 16A switch 1No. with GI modular box and face plate and all other acessories.

Supply and installation with modular plate and cover in front on surface or in recess, including providing and installation 1set 6/16 A modular universal socket outlet with 16A modular switch and 1set 6 A modular universal socket outlet with 6A modular switch , connections etc. as required in a single modular plate for UPS power

Providing and installation 4.00 (8 SWG) mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supply & installation of 36W LED (Recessed mount type suitable for 2X2 grid ceiling) light fixtures using efficient optics system lumen, fully acrylic LED luminaire, CRCA housing with high efficiency opal diffuser, zero maintenance, zero mercury System Wattage: 36Watts Efficiency 100 lumen/Watt CRI 75%.

Supply & installation of 15W LED round light fixture(Recessed mount type)with cool day light (Model: Havells ENDURA NEO DLR 15W LED 840 MOD or Equivalent)

Supply and drawing 1 run of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supply, Installation ,testing & commissioning of category 6U /UTP outlet for voice and data

Supply and installation of 2-Port Faceplate Shuttered Square type White colour cost include blank insert required for all

Supply and installation Cat 6 1m Patch Cords of required length

Supply and installation Cat 6 24 Port Jack panel - preloaded Source Panel with all connected accessories

Supply and installation Cat 6 24 port unloaded patch panel with all connected accessories

Supply, Installation ,testing & commissioning of Hot Dip GI 2.44m floor race way of size 100x38 mm with cover

Supply, Installation ,testing & commissioning of Hot Dip GI 2.44m floor race way of size 50x38 mm with cover

Supply and installation of 38 mm PVC Channel (Casing cap)

Supply and installation of PVC Channel 50x50 (Trunking)