Department Of Local Administration Tender

Code No11.3.1: Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

Code No.5.9.3: Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors , roofs , landings , balconies and access platform

Code No.5.3: Reinforced cement concrete work in beams,suspended floors , roofs having slope up to 15degree landings , balconies , shelves , chajjas , lintels , bands , plain window sills , staircases and spiral stair cases upto floor five level excluing the cost of centering ,shuttering, finishing and reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No.13.1.1: 12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Code No.13.16.1 : 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Code No.9.117.2: Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 42 x 50 mm

Code No .9.118.2: Providing and fixing to existing door frames - 30 mm thick factory made Polyvinyl Chloride (PVC) door shutters made of styles and rails of a uPVC hollow section of size 60 x 30 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt decorative moulding edging on one side . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 25x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 30 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification

Code No.9.147B.1: Providing and fixing factory made uPVC white colour fixed glazed windows / ventilators comprising of uPVC multi - chambered frame and mullion (where ever required ) extruded profiles duly reinforced with 1.6 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket, G.I.fastners 100 x 8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners , mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , all complete as per approved drawing. (Single / double glass panes and silicon sealant shall be paid separately) - Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 + or - 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm) - Fixed window size - 1.20x0.50 m

Code No.31.160.1A: Providing, laying and jointing UPVC pipes(Finolex /Jain / Supreme / Truebore / Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, incuding cost of solvent cement,UPVC specials such as bends,tees, threaded pieces, couplers, reducer,endcaps etc.,complete all as per IS and CPWD specification. - 20mm dia.

Code No.18.51.1: Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore

Code No.17.2.1: Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid

Code No.31.162.1D: Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer,endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No.18.48A:Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Code No.13.43.1: Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Code No.13.60.1: Wall painting with acrylic emulsion paint of approved brand and manufacturer to give an even shade - Two or more coats on new work

Code No.5.22.7: Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more

Code No.17.23: Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410x265mm sizes respectively

Code No.31.160.1G:Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends,tees, threaded pieces, couplers ,reducer, endcaps etc.,complete all as per IS and CPWD specification. - 75mm dia.

Code No.31.10.3.2: Providing and fixing ball valve (brass) of approved quality complete - high or low pressure with plastic floats - 20 mm nominal bore.

Code No.6.12.2: Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in - cement mortar 1:4 (1 cement :4 coarse sand)

Code No.Non PSR item: Supply laying to line and connecting septic tank having capacity 20 to 25 flush per day of polethene made out of centrifugal moulding manufactured as a single piece leak proof type II of size 200x100 dia having a wall thickness of 10 mm with two man holes with inlet for 110mm dia pipe with 2 or 3 inner chamber polethene septic tank united type II

Code No.19.33A: Constructing soak pit 1.20 x 1.20 x1.20 m filled with brick bats including 110 mm dia UPVC pipe (type B) 1.20 m long complete as per standard design

Code No.5.9.5: Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams , girders , bressumers and catilevers

Code No.17.7.4: Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap

Code No.18.53.1: Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Code No.17.78.1: Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore

Code No.9.165.1A: Providing and fixing of 65mm Godrej Navatal lock of 6 levers etc complete

Code No.11.38: Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer) , of 1st quality conforming to IS :15622, of approved make , in all colours, shades, except white , ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigments etc., complete

Code No.11.36A: Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 200 x 300 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 200x300 mm