University Of Agricultural Sciences Tender

code12 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling with dash fasteners of required dia and size, including necessary filling up the gaps at juctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (glazing,paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hingers/ pivots and making provision for fixing of fittings wherever required (Fittings shall be paid for EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powdre coating 50 micron) including cost of materials, labour, usage charges of machinery complete as per specifications.

code10 - Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end locks, mounted on specially desingned pipe shaft with brackets, side guides and arrengements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS:4454-part 1 and M.S. laths with 1.25 mm thick top cover including cost of materials, labour, Usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

code14 - Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two coat applied @ 1.67 ltr/10m2 over and including priming coat of exterior primer applied @ 2.20 kg/10 m2) with paint of approved quality to give an even shade, after throughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including prepairing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code03 - Providing and laying in Reinforced cement concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super pasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, labour,Usage charges of machinery, curing of all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid seperately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates.

code13 - Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two coats on new work after throughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including prepairing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code07 - Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C work including straighening, cutting, bending,placing in position, binding and anchoring to adjacent members wherever necessary complete as per design including cost of material, labour, usage charges complete as per specifications.(The laps and wastages shall not be measured separately)

code09 - Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand ) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

code06 - Providing and fixing Strutural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials,labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-charge.

code04 - Providing and filling murrum / gravely soil (CNS soil) for foundation or around pipes including cost of all materials, labour, spreading soil in layers of 100 to 150 mm, breaking codes, watering, complection by earth masters to achieve density control of not less than 90 percent etc., complete with all lead and lifts.

code05 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in foundation and plinth in Cement mortar 1:6 (1cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinary & other incidenal charges complete as per the direction of engineer incharge of work.

code11 - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.

code15 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevent IS codes machine mixed with super plasticizers laid in finished layers,well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirement of relevent IS Codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates.

code16 - Vaccum de-watering with vaccum pump and suction mat and compaction with skin floater clubbed with floating dicincluding cost of generator, HOM of machinary, scred vibratory power floater blade and disc etc., with all lead and lift.