Public Works Department Tender

PWD UNI SR 2023-24 vol-2 Page no 59 Item no 9.6.2 - 9.6.2 Providing and laying Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) Medium shade pigment using 50% white cement 50% Grey cement ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no A-28 Item no 548 - Providing and fixing Screws approved Nails and screws of sizes for structural glazing /ACP Cladding ( Material Components P.No - A28 I.No 548 ) ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 60 Item no 9.11 - 9.11 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including pointing the joints with white cement and matching pigments etc., complete. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 41 Item no 8.3.1 - 8.3.1 Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 99 Item no 12.15 - 12.15 Providing and fixing in position fully panelled Honne wood shutters for doors with stiles and rails of 40mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. ( excluding cost of fixtures. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 42 Item no 8.8 - 8.8 Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mortar 1:6 (1 cement : 6 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 105 Item no 12.6 - 12.60 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 62 Item no 9.21.2 - 9.21.2 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 18 Item no 2.11 - 2.11 Steel Fabrication Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification.a. Buildings ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 71 Item no 10.18 - 10.18 Providing and fixing of wall cladding using 20mm thick gang saw water cut Shiva gold granite, grey granite in CM 1:3 (1 cement : 3 coarse sand) proportion cut to required shape, pattern with paper joints, finished with cement mortal using white cement and colour pigments to match the colour of slab making through jointing with sealant, making holes 25mmx12mm grooves in joints including cost of all materials, mortar, labour, curing etc., complete. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 65 Item no 9.38 - 9.38 Providing skirting, dadooing, rises of steps with white glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, complete as per specifications. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 110 Item no 12.9 - Providing and fixing of 3track 2panel sliding windows made out of multi chambered UPVC Matching to RAL 9016 sections and with minimum TO2 Titanium Dioxide at 6PHR with TPE Thermo Plastic Elastomerand lead free gaskets grey colour having isolated drainage and reinforced with Galvanized Iron profile through out the window frame.The outer frame having an overall size of 108mm width 45mm height with reinforcement of 1mm thickness and Sash with overall size of 39mm 75mm with GI reinforcement of 2mm and mesh sash of size 37mm 58mm Co extruded Glazing bead for fixing of glass shall be of size 20mm 24 mm Windows shall be provided with 6mm plain float glass standard hardware and Multi point locking system with touch lock. Wall thickness of frame and sash shall be of 2mm 2.5mm Maximum possible size 2419 mm 2200 mm The cost is inclusive of all fixtures and separate charges for minor T P s shall not be made ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.5.2 - ADD FORMWORK FOR LINTEL,SLAB BEAM ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 46 Item no 8.3 - Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.4.3 - ADD FORMWORK FOR COLUMN ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 50 Item no 8.51 - 8.51 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer in charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 51 Item no 8.63 - 8.63 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One coats on old work as per specifications and as per directions of Engineer in charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no A-25 Item no 444 - Providing and fixing Hold fasts for doors etc complete ( Material Components P.No -A25 I.No 444 ) ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 63 Item no 9.25 - 9.25 Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.5.2 - 2.5.2 Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement, dowel bars & formwork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 36 Item no 1.12 - 1.12 Earth work in surface excavation by mechanical means for lowering &leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and technicalspecifications, including setting out, shoring, strutting,barricading,caution lights, removal of stumps and other deleterious matter includingdressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radiusof 50 m and lift upto 1.5 m including cost of labour, tools, usage ofmachinery & other appurtenances required to complete the work. In all kinds of soils upto 300 mm depth ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 15 Item no 2.2.3 - ADD FORMWORK FOR FOOTING ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 105 Item no 12.63 - 12.63 Providing and fixing aluminium tower bolts, ISI marked, anodised (an- odic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 108 Item no 12.83 - Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance 1mm), with wall thickness 2.0 mm ( 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm ( 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer in charge ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 105 Item no 12.57 - 12.57.4 Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround door shutters covered with cross bonded wooden sheets (core veneer) hot pressed and fastened on both sides of the door useing liquid phenol formaldehyde resin as per IS specifications 2202 (part-I) 1991. from manufacturer complete as per spcification.12.57.4 -do- 35 mm thick both side Teak ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 64 Item no 9.36 - 9.36 Providing flooring with 25mm thick polished Cuddapah slabs using cement mortar 1:6, 25mm thick over existing cement concrete bed or top of roof laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the slab , including cost of materials, labour, curing, polishing complete as per specifications. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 25 Item no 7.32.3 - Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 g/m2 (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 9 Item no 5.1.1 - 5.1.1 Providing Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand) ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.5.2 - ADD FORMWORK FOR CHAJJA ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 104 Item no 12.51 - 12.51 Fixing of door frame in an existing opening including embedding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size granite metal painting two coats of coal tar to sides of frame, making good the damages to walls and floor as required and disposal of the debris with lead upto 50 m. including cost of materials, labour charges, complete as per specifications. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 104 Item no 12.53 - 12.53 Providing & fixing 30mm thick factory made rigid foam Panelled Door Shutters made from M.S. tube of 19 gauge thickness, size 19x19mm for stiles and 15x15mm for top & bottom rails, covered with heat moulded PVC C channel of 5mm thick sheet & 30 x 50mm wide to form stiles & 5mm thick & 75mm wide PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick 20mm wide PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet fitted in the M.S. Frame, Sealed to the stiles & rails with 5x30mm PVC sheet beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction of Engineer-in-charge fixed to frames with 3 nos of 75 mm Aluminium hinges. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 14 Item no 6.8 - 6.8 Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 86 Item no 11.34A - 11.34A Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 15 Item no 2.2.3 - 2.2.3 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.4.3 - ADD FORMWORK FOR PLINTH BEAM ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 47 Item no 8.34.1 - 8.34.1 Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 16 Item no 2.5.2 - ADD FORMWORK FOR SLAB & STAIRCASE ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 7 Item no 1.11 - 1.11 Filling approved earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 15 Item no 2.1.4 - 2.1.4 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 106 Item no 12.69 - 12.69.2 Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc.125mm ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 49 Item no 8.45.2 - 8.45.2 Varnishing with varnish of approved brand and manufacture :Two coats glue sizing with spar varnish or an under coat of flatting varnish to give an even shade and produce a smooth dry and mat surface including preparing the surface after thorougly cleaning oil, grease, dirt and foreign mattersand papering and knotting , cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 41 Item no 8.1.1 - 8.1.1 Providing 12 mm cement plaster with cement mortar 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 107 Item no 12.73 - 12.73.1 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 45 Item no 8.29 - 8.29 Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 m²) over and including priming coat of exterior primer applied @ 2.20kg/10 m² to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 99 Item no 12.9 - 12.9 Providing Sal wood frames for false ceiling, partitions etc., main battens of size 50x12.5mm at 600 mm c/c and cross battons 38mmx50mm at 600mm c/c sawn and putup including cost of materials, labour complete as per specifications. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 14 Item no 6.15 - 6.15 Providing Half brick masonry with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level up to floor 1 level cement mortar 1:4 (1 cement :4 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-2 Page no 85 Item no 11.28 - 11.28 Providing and fixing 304 - grade stainless steel hand rails of 14-gauge pipes for Ramps or Staircase are made out of stainless steel hallow pipes, using 50mm dia for verticals @1.60 mtr c/c are fixed to the ramps or steps by drilling with bolts and 100mm dia MS base plates 10mm gauge for fixing of Vertical pipes 4 - Nos anchor bolts & 40mm dia pipes are fixed horizontally for 2-rows top, one pipes are fixed with vertical pipes another one are fixed with elbows and 25mm dia pipes are fixed horizontally for 2-rows below top measure @ equal intervals including cutting, welding, bending wherever necessary with suitable caps @ tops, bottoms & corners finishing with mat / shining etc., complete including cost and conveyance of all materials, labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work. Ramps or Staircase for physically challenged. ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 8 Item no 1.14.1 - 1.14.1 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 15 Item no 2.1.3 - 2.1.3 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregates ---- including cost of all materials, labor ,HOM,l

PWD UNI SR 2023-24 vol-1 Page no 7 Item no 1.9 - 1.9 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. ---- including cost of all materials, labor ,HOM,l