Mysore University Tender

14.5.1 - Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

14.11.2 - Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

14.7A - Providing and fixing wash basin with C.I. brackets, 15 mm dia CP brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: using White Vitreous China Wash basin size 550x400 mm with a 15 mm CP brass single hole basin mixer

9.19 - Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser, treads of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints as per direction of Engineer in charge.

YCM8 - Big Mic Stand

2.11 - Steel Fabrication Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. Buildings

14.16A - Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

13.20.1 - Providing and fixing PTMT pillar cock of approved quality and colour: 15 mm nominal bore, 107 mm long, weighing not less than 110 g

13.34 - Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

6.33 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x150x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications.

12.97.1 - Providing and fixing to existing door frames Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. - 30 mm thickness

YCM22 - Providing, fabricating, supplying and installing/furnishing Island Laboratory tables as per approved drawing, design and following specifications and directions. Below the work top i.e., underneath module should be made with 19mm thick both side mechanically laminated (1mm ) ply wood (marine ply / BWR grade ply wood) confirm to relevant ISS for all bottom, horizontal, vertical, shutters, drawers and other required numbers. Each table shall be 6 nos of cabines & one shutters compartment (1D/1S) All the cabines are fixed using telescopic channels (S.S coated / S.S rollers) for movement arrangements. The shutters shall be with Ebco/Haffele/Hettich Make NP Concealed Clip on full overlay Hinges, or SS 'U' shaped handles, the outer all-round edges of shutters and drawers shall be with approved type over 2 mm thick mechanically gloved edge banding and necessary locking arrangements with keys shall be made to drawers and shutters. Necessary PVC bottom leg support.The cost including grarite top, drawers and shutters, all hardware fittings including screws etc. The rate including cost of all materials, labour, all making charges fixing and installation charges all charges, transportation loading and unloading, entry tax of duties and all other incidental charges required for successful installation at lab.

13.2.1 - Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

14.52a - Providing and fixing Angle cock light with wall flange made of Stainless steel with all concealed fitting arrangements & all necessary accesories complete - class - Economy

13.31.5 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - 40 mm nominal dia Pipes

10.1.9 - Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For: PVC pipes 160mm dia., 6 kg/sqcm & class 3

2.2.1 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. - m²0 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

YCM10 - F10 II Cordless Microphone

YCM1 - Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI frame and cover.

20.104 - Repairing and fixing shutters (panelled or glazed) to doors, windows, ventilators and cupboards.

14.28.2.1 - Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe : 32 mm dia

YCM13 - Microphone Cable

YCM21 - 3 seater Bench & Desk for Class Room: Supply, delivery and assembling bench & desk unit of size 1800mm as shown in the drawing with the following specifications: The overall dimensions should be of size 1800mmx895mmx750mm. The Plywood panel for Desk (1800x378x18mm), seat (1800x335x25mm) and back (1800x265x18mm) should be made of both side 0.8mm thick pre-laminated sheet confirming to IS 10701: 2012, the edges should be rounded duly sealed with 2mm thick 18mm & 25mm wide hot pressed PVC (Poly Vinyl Chloride) beading and fixed to the understructure supporting the ply wood sheet with power driven 16mm screws to the square tubes. The understructure should be made of 25.0mm square tube 1.6mm thick powder coated ERW (Electrical Resistant Welded) frames at base which should be welded to the desk and seat supports that are made of 1.0mm thick powder coated 27.5mm x 25.4mm C channel frame sections. (3) Vertical frames at base and back of seat made of 25.0mm sq. tube x 1.6mm thick powder coated ERW tubes should be provided with 25mm Sq. tubes stiffeners between them fixed with threaded screws. These frames, legs & open ends should be closed with PVC caps. The storage shelf closed on three sides should be made from 0.8mm thick powder coated MS sheet affixed with self thread screws below the desktop and the frame supporting to the desk top. Hooks made from 6.0mm dia MS rods should be provided on eigher side of the vertical frame of the desk, for hanging bags/bottles. All wooden panels shall be half rounded at corners. Steel used should confirm to IS-513. The legs shall be provided with PVC bushes steel used should undergo pre treatment process as per IS 3618 - 1996. All structural steel fabricated components requiring welding are spot welded and finished with Epoxy polyester powder coating DFT (Dry Film Thickness) of 45 microns as per IS101. Complete for finished item of work, the item shall carry a warranty period of 2 years (24 months) from the date of supply. The rate including cost of all materials, labour and all types of incidental charges, transportation, lead and lift etc., complete.

YCM20 - Power Supply 220V 50/60Hz

14.6.1 - Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Single squatting plate with 5 litre P.V.C. automatic flushing cistern

12.96 - Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber Glass from all sides. M.S. stay shall be provided at the bottom to steady the frame

YCM14 - XRL Connector-P38

5.2 - Providing Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)

YCM17 - Specs:

14.19.1 - Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre (full flush) capacity-white

YCM2 - Cleaning of glazed tiles. including cost of materials, labour, HOM complete as per specifications.

YCM5 - Air 12 mixer Specs: 12 Mic/Line 3 Band EQ Per Channel 1 Aux send PFL Switch with individual channel control L/R Pan pot and clip LED per channel 8 Segments L/R LED meter for master level

YCM6 - F 20 hh cordless mic dual Specs: Dynamic Range 100db Frequency Stability +/- 0.3% Max Frequency +/- 15kHz Rate Current 480 mAh

15.2 - polyurethane based single Component for Existing surface - Providing and Applying PU based Elastomeric Liquid Applied PU Waterproofing Membrane single component, cold applied, water based acrylic PU dispersion with highly elastic and UV resistant water proofing treatment to the Existing Roof surface/Chajjas/Sunken portion of WC:Bathroom applied @ 1.2 l/per m2, having tensile strength greater than 1.5N/mm2, elongation greater than 300% with solid content not less than 60% in 2 coats including surface preparation, priming the surface with water based acrylic primer @0.1 l/m2, and spreading 60 gsm geotextile between two top coats completely as per specification. The finished cost to include surface preparation, making coving at Junction, Bore Packing, treatment of construction joints completely as per specification.

9.1 - Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per m2 including pointing in white cement mixed with pigment of matching shade complete.

14.1.1 - Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

14.3.1 - Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

YCM16 - 4000 power amp to drive speaker and subwoofer

2.1.2 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. - Mix 1:4:8 Using 40 mm nominal size graded crushed coarse aggregates

8.5.1 - Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

15.28 - Toilets Tile Joints (Repair) - Providing and grouting tile joints, Cutting the tile joints with the help of cutting machine (width 3mm-15mm) and filling with of matching shade, using three component Epoxy based tile joint filler, non-sag waterproof grout, chemical and UV resistance, Pot life ≤ 60 mins, VOC (EPA 24) < 8gm/kg and water absorption after 7 days < 0.5g Joints shall be clean, dry, free from dirt, etc prior to application. Apply tile grout using a rubber trowel/grout floater, press firmly into joints, ensure complete fill and remove excess grout from surface using suitable method. The work shall be carried out as per the directions of the Engineer in charge.

14.36.1 - Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 g

10.1.7 - Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For: PVC pipes 110mm dia., 6 kg/sqcm & class 3

13.31.6 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - 50 mm nominal dia Pipes

9.24 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. ** Polished Granite stone slab Black, Cat Eye, River Pink or equivalent.

YCM12 - 100/40 Speaker Cable 1.5 Sqmt

YCM15 - Spekon

20.88 - Repairs to plaster in patches of 2.5 m2 and less in walls, ceilings 10 to 20mm thick in cement mortar 1:3 including cutting the patches in proper shape and replastering the surface of the wall including disposal of rubbish with a lead of 50m including curing cost of materials, labour, complete as per specification.

YCM7 - CM-185 podium Mic Specs: Output 160O+-20% Max SPL 105dB(F=1KHz,THD5%) Max Output 250mV 1.35mA(-68+-2 dBm) Length 400 mm

2.1.6 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. - Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates

13.31.2 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - 20 mm nominal dia Pipes

1.4.1 - Manual Means - Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m

YCM9 - Monitor Speaker 12 Inch Specs: 155 Mm Ferrite Magnet Pressed Metal Iron Frame 400 W Continuous Power Handling 2.5 Inch Copper Voice Coil on Kapton 97 dB Sensitivity Excellent Low Frequency Response Special High Temperature Voice Coil

YCM11 - Pendrive MP3 Player Specs: Bluetooth Connectivity Audio Recording Compatible with Android and IOS

13.4.4 - Providing and fixing brass full way valve gate with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

YCM18 - Damping Factor 450:1

13.31.3 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - 25 mm nominal dia Pipes

19.22.1 - Dismantling tile work in floors and roofs laid in cement mortar includ- ing stacking material to the appropriate disposal area as per direction of Engineer-in-charge.For thickness of tiles 10 mm to 25 mm

YCM19 - Input Sensitivity 0.775V, 1.0v, 1.55V