Minor Irrigation Department Tender

code08 - Supply of ISI mark 175mm nominal bore,plain and steel casing pipe grade of steel Fe 410 of wall thickness conforming to IS 4270-2001 andlatest ammendments, electrical resistance welded steel tubes, materialand conforming to IS 1387-1993 and manufactured by basic openhearth electric or basic oxygen process in random length of 5-7m both ends.threaded conforming to IS 554-1985 one end fixed with socketconforming to IS 4270-2001 and the other end with screwed pipes allshall be responsibaly free from defects. The tubes shall be responsiblestraight end should be with ISI marking weighing 25.10kg/m.pricesinclude Collar-Medium duty.

code02 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata includingover burdern upto 20 m. Fixing of casing pipes, collars and cap withnecessary cutting, threading and welding including transportation ofrig and supporting vehicle, crew charges and cost of consumables etc.,complete including yield testing at the final depth with a minimumworking of compressor for one hour (Excluding cost of casing pipes,collars, cap etc.complete) 00.0 to 50.00 m.

code17 - Supplying, fixing and wiring heavy duty low voltage capacitors conforming to IS 2834. 3phase, 400/440 Vgrade, for power factor improvement of rotating machineries like induction motor.

code03 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata includingover burdern upto 20 m. Fixing of casing pipes, collars and cap withnecessary cutting, threading and welding including transportation ofrig and supporting vehicle, crew charges and cost of consumables etc.,complete including yield testing at the final depth with a minimumworking of compressor for one hour (Excluding cost of casing pipes,collars, cap etc.complete) 50.0 to 100.00 m.

code18 - Fabricating supplying and mounting MS box made out 16 SWG suitable for floor/wall mounting, fully weather proof with provision for better heat dissipation, provided withhinged front cover, equipped with tamper proof locking arrangements,with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tank streatment with powder coated paintand finally finished with approved colour etc., complete.

code01 - Geophysical investigation at site for sinking borewells for Providing drinking water to the habitation either through the Hand Pump MWS or P.W.S.S, by vertical electrical sounding by adopting Venner or Schlumbergers's method, including reconnaissance survey of geological formation. Geophysical investigation of existing ground water in the vicinity, its quality, quantity and acceptability of the users, indicating the location of the site, recommended depth of casing pipe required to seal the top unconsolidated formation including an extra depth of 1.0 metre in consolidated formation for proper seating of casing pipe, depth of drilling required to cover full depth of aquifer proposed to be tapped, probable yield and other information required including transportation of instruments and accessories to work site, engaging technical personal and labour required etc.

code15 - Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog Voltmeter 1ni with Phase selector switch, Isolating switch OUTGOING for Main Electrical Pump: 1 No. MCB 1 No. DOL of S/D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor, under voltage over Volage, under current over current & dry run protection suitable for the pump described above 1 no Indoor type NOTE: 1) DOL- Direct Online Starter 2) S-D- Star Delta Starter etc. complete. 6 to 15 HP pumps.

code09 - Providing and laying at site of work MS casing caps as per IS 1239 (part-II) 1982 with all latest amendments if any for any dia. The thicknessof plate used for covering one end shall be 3mm (minimum). Thedimensions of caps and colars shall be strictly as per IS 1239 (Part-II)1982 with all amendments including cost of material and labour chargesfor fixing, if any etc. complete with all lead and lifts and as directed by the Engineer in charge

code14 - Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm

code04 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata includingover burdern upto 20 m. Fixing of casing pipes, collars and cap withnecessary cutting, threading and welding including transportation ofrig and supporting vehicle, crew charges and cost of consumables etc.,complete including yield testing at the final depth with a minimumworking of compressor for one hour (Excluding cost of casing pipes,collars, cap etc.complete) 100.0 to 150.00 m.

code11 - Supply and delivery of galvanized mild steel tubes of 6mtr standard length heavy duty (C Class) as per IS 1239 (Part-I) 1990 with latest amendments with ISI Mark (one end fitted with Heavy Duty collar and other end fitted with protective cover) 50 mm.

code16 - Supplying and fixing HRC fuse units base on existing switch /panel board. 100 to 300 A.

code10 - Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. For 3 HP etc. complete. 10.00 HP - 90 LPM @ 220 m = 20 STG Outlet Dia - 2.00"

code12 - Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments, 1x3x6 Sqm.

code07 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata includingover burdern upto 20 m. Fixing of casing pipes, collars and cap withnecessary cutting, threading and welding including transportation ofrig and supporting vehicle, crew charges and cost of consumables etc.,complete including yield testing at the final depth with a minimumworking of compressor for one hour (Excluding cost of casing pipes,collars, cap etc.complete) 250.0 to 300.00 m.