Karnataka Veterinary Animal And Fisheries Sciences University Tender

code08 - Supplying and flush mounting teak wooden box without front plank, made of not less than 12mm thick wood, after due groove cutting, necessary masonry patch work complete. a)12x"12"x3" (300x300x76mm)

code12 - Supply and fixing of bakelite D.P/Socket/ switch with/without neon indicator over existing wood board or flush mounting in plastic plates/nitches.a) 32Amps Flush/projected type DP switch

code09 - Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing the wall up to wall surface complete. a) up to 50mm conduit in brick wall

code16 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required. Group 'A' a) 5-32Amps SP

code18 - Supplying and fixing/replacing of 6/16/32Amps electrical accessories on existing switch board.(50/34) b) 6 Amps lamp holder

code19 - Supplying and fixing/replacing of 6/16/32Amps electrical accessories on existing switch board.(50/34) c) 16 Amps SP switch

code04 - Providing applying two coats of wall putty to inside plastered walls and ceiling using white cement putty. Scrapping and levelling the surface using steel blade and preparing the surface even and smooth by using different grade sand papers, including cost of all materials, cost of labour and scaffolding etc., complete as per the specification. (P.No. 125, I.No. 15.106 of SR 2021-22).

code17 - Supplying and fixing/replacing of 6/16/32Amps electrical accessories on existing switch board.(50/34) a) 6Amps Bakelite ceiling rose

code06 - KSRB 15-17.6 : Providing and applying painting two coats ( excluding priming coat ) on new wood surface and / or wood based surface with enamel paint to give an even shade, cleaning the surface of all dirt, dust and foreign matter, sand papering including cost of materials, labour, complete as per specifications.

code26 - Providing and laying in position reinforced cement concrete of nominal mix 1:1.5:3 with 20mm and down size graded granite metal, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation plinth and ground floor level for columns, including cost of all materials, labour, HOM of machinery, curing, complete

code13 - Wiring for lighting/power circuit using one of PVC insulated 1100v grade, multistrand Copper conductor single core cable in open or concealed system of wiring. b.1.5 sqmm

code33 - Providing and laying in position plain cement concrete of mix 1:2:4 using 20mm and down size graded granite metal machine mixed, concrete laid in layers not exceeding 15 cms, thick, well compacted, in foundation and plinth, including cost of all materials, labour, HOM of machinery, curing complete as per specifications.

code36 - Providing and applying painting in two coats with plastic emulsion paint with primer of approved brand on wall surface to give an even approved shade after throughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications.

code11 - Supplying 6A flush/projected type socket and 6 amps flush/projected type SP switch either surface/flush mounting in a existing gang box or in a 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required.b) 6Amps 3/5 Way

code14 - Wiring for lighting/power circuit using one of PVC insulated 1100v grade, multistrand Copper conductor single core cable in open or concealed system of wiring. c.2.5 sqmm

code32 - KSRB 5-14 : Providing and constructing precast concrete solid blocks with compressive strength not less than 35 Kg/sqm with cement mortar 1:4 masonry (quoin, Jamb, closer blocks) with solid concrete blocks of size 40x20x20 cms conforming to I.S: 2185/1965 in superstructure including cost of materials, labour charges, scaffolding, curing complete as per specifications. (P.26/I.5.27 PW, P & IWTD SR - )

code31 - Providing TMT steel reinforcement for R.C.C. work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps and wastage shall not be measured and paid) cost of materials, labour, HOM of machinery complete as per specifications.

code02 - KSRB 7.16 : Providing, fabricating, assembling and fixing in position aluminium shutters to the existing door frame in the partition using 47.62x44.45mm section thickness 3.18mm, weight 1.505kg/m for vertical frame; 47.62x44.45 thickness of 3mm, weight 1.42kg/m for top section, 49.91mmx44.45mm with wall thickness 3mm, weight 1.495kg/ m for central rail; and 114.3mmx44.45mm thickness 3.18mm, weight 2.646kg/m for bottom rail; aluminium sections and cut to length joint metred and corners grinded, the bottom rail and top rail hinged or pivoted, opening arrangements including providing and fixing standard approved accessories, such as aluminium handles, tower bolts, lock, pivots: hinges P.V.C. or rubber gasket, 12mm prelaminated sheets ( Novopan) exterior grade of approved colour both sides same colour for bottom panel of maximum height 0.90m and 5.5mm thick plain glass for top panel ( Novopan ) and glass fixed with glazed clips 19mmx17.3mmx11mm, 0.9mm thick, weight 0.124kg/m; aluminium sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherance of mortars or any other sticky materials, including cost of materials, fixtures, labour and HOM of machinery complete as per specifications. using aluminium section powdered coated to a minimum of 60-70 microns with exterior durable pure polyester grade powder of approved quality.

code30 - Providing and removing centering, shuttering, strutting, propping etc. for plinth Beam, including cost of all materials, labour complete as per specification.

code10 - Point wiring using Copper wire with switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using copper PVC insulated multi strand 2x1.5Sqmm copper wire with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. I. Point wiring using class A Materials c) Long point above 6Mtr up to 10Mtr from tapping point to out let via switch

code22 - Earthwork in Ordinaery soil for leveling and lowering the ground manually and removing the excavated stuff to a distance not exceeding 50m and lift upto 1.5m, excavated surface leveled and neatly dressed, disposed earth to be leveled after breaking clods and neatly dressed as per specifications.

code01 - Providing and fixing Special make glazed Vitrified tiles (Granomite finish) of approved make, quality and colour of size 600x600x10mm thick fixed on existing flooring with a special roffe adhesive for flooring and skirting etc., complete including providing spears at required interval and removing stains etc., complete.

code29 - Providing and laying in position reinforced cement concrete of nominal mix 1:1.5:3 with 20mm and down size graded granite metal, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation plinth and ground floor level for plinth Beam, including cost of all materials, labour, HOM of machinery, curing, complete

code28 - Filling available excavated earth (excluding rock) in sides of foundations upto plinth in layers not exceeding 20 cms. in depth, compacting each deposited layer by ramming after watering with lead upto 50 m. and lift upto 1.5 m. including cost of all labour complete as per specifications.

code35 - Providing 10cm wide 10mm thick platering beading to the compound wall including smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. (MR)

code34 - Providing 18mm thick cement plaster in single coat with cement mortar 1:3, to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications.

code23 - Earth work excavation in hard soil for foundation of buildings, 1.5m and above in width, in ordinary soil not exceeding 1.5 m. in depth including dressings the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m. after breaking of clods complete as per specifications.

code37 - Providing and fixing of broken glass pieces on existing compound wall coping includung cost of all materials labour complete

code03 - KSRB 8.7-2 : Providing and fixing in position 10mm thick plaster of paris (Gypsum anhydrous ) for ceiling curved surface upto a height of 5 m above floor level over aluminium strips 25mm / 6mm with 10mm gap in between and reinforced with rabbit wire mesh fixed to meatal frames including cost of materials, labour, curing complete as per specifications.

code20 - Supplying and fixing/replacing of 6/16/32Amps electrical accessories on existing switch board.(50/34) d) 16 Amps 3 way 5 pin socket

code25 - Providing and laying in position reinforced cement concrete of nominal mix 1:1.5:3 with 20mm and down size graded granite metal, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation plinth and ground floor level for footing, including cost of all materials, labour, HOM of machinery, curing, complete

code27 - Providing and removing centering, shuttering, strutting, propping etc. for columns, including cost of all materials, labour complete as per specification.

code21 - Supplying and fixing/replacing of 6/16/32Amps electrical accessories on existing switch board.(50/34) f) 32 Amps baklite DP

code24 - Providing and laying in position plain cement concrete of mix 1:4:8 using 40mm and down size graded granite metal machine mixed, concrete laid in layers not exceeding 15 cms, thick, well compacted, in foundation and plinth, including cost of all materials, labour, HOM of machinery, curing complete as per specifications.