Karnataka State Police Housing And Infrastructure Development Corporation Limited Tender

Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamp at 1.00 mtr spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement & the cost of cutting chases & making good the same including testing of joints complete. (Concealed work including cutting chases and good the walls etc.) - 32mm nominal OD pipes ---- as per directions of engineer in charge of work.

KSRB13-8.9 : Providing and fixing to wall, ceiling and floor, low density polyethylene pipes 6.00 kgf/sq.cm working pressure 110mm outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications. Specification No.KBS 13.2.15.1 / 13.9 ---- as per directions of engineer in charge of work.

Constructing brick masonry inspection chamber 600x600mm, and 450mm depth, ( clear inside dimension ) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg ( weight of cover 23kg and weight of frame 15 kg) R.C.C. top slab with cement concrete M 15 with 20mm and downsize granite metal, foundation concrete M 5 with 40mm and downsize granite metal inside plastering 12mm thick with cement mortar 1:3, finish smooth with a floating coat of cement on walls and bed concrete complete as per standard design including cost of materials, labour charges, curing complete as per specifications. Specification No. KBS 600x600mm and 450mm depth ( clear inside dimension ) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 600x600mm ---- as per directions of engineer in charge of work.

Constructing brick masonry inspection chamber 450x450mm, and 450mm depth, ( clear inside dimension ) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg ( weight of cover 23kg and weight of frame 15 kg) R.C.C. top slab with cement concrete M 15 with 20mm and downsize granite metal, foundation concrete M 5 with 40mm and downsize granite metal inside plastering 12mm thick with cement mortar 1:3, finish smooth with a floating coat of cement on walls and bed concrete complete as per standard design including cost of materials, labour charges, curing complete as per specifications. Specification No. KBS 450x450mm and 450mm depth ( clear inside dimension ) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 450x450mm ---- as per directions of engineer in charge of work.

KSRB13-6.3-4 : Providing and fixing in position brass gate valve with C.I wheel of approved quality ( screwed end ) 32mm nominal bore including cost of all materials, labour and HOM of equipments with all leads complete as per specifications. Specification No.KBS 13.2.6 / 13.3 ---- as per directions of engineer in charge of work.

KSRB13-6.3-3 : Providing and fixing in position brass gate valve with C.I wheel of approved quality ( screwed end ) 25mm nominal bore including cost of all materials, labour and HOM of equipments with all leads complete as per specifications. Specification No.KBS 13.2.6 / 13.3 ---- as per directions of engineer in charge of work.

KSRB 13-11.1 : Providing and placing on terrace, polyethylene water storage tanks with manhole lid and suitable locking arrangements, making holes of suitable diameter for inlet, outlet and over flow pipes, including cost of all materials, labour, transport charges, HOM of equipments and testing complete as per specifications.(For 1000 litre capacity) Specification No.KBS 13.22 ---- as per directions of engineer in charge of work.

Geophysical investigation of site for sinking Bore well for supplying drinking water to the habitaion either through hand pump scheme mini water supply scheme or piped water supply scheme by vertical elctrical sounding by adopting vannur are schlumbergers method . including re connissance survey of geological formation. Geohidroligical investigation of existing ground water in the vicinity its quality. Quantity and acceptablity of the user. Indicating the location of site . Recommended depth of casing pipe required to seal the top un consolidated formation including extra depth of 1mt in consolidated formation for proper ceating of casing pipes. Depth of drilling corvering full depth of aquifer proposed to be tapped. probable yield and other information required for safe drinking and harnessing including transportation of instrument and accessories to work site. engaging techinical personnel and lobour required etc complete. ---- as per directions of engineer in charge of work.

Sinking the Bore well of the 150mm dia clear using super fast hydrolic ring of capacity 250PSIG & above 900CFM& above in all strata including over burden up to 20mm. Fixing of casing pipes ,collears and cap with ncessory cutting threding and welding including transpotation of ring and supporting vehicle. Crew charges and cost of consumables etc complete including yield testing at that final depth with a minimum working of compressor for 1 hour (excluding cost of casing pipes,collars, and cap. etc ) i) Up to 0.00 to 50.00 mtrs ---- as per directions of engineer in charge of work.

Sinking the Bore well of the 150mm dia clear using super fast hydrolic ring of capacity 250PSIG & above 900CFM& above in all strata including over burden up to 20mm. Fixing of casing pipes ,collears and cap with ncessory cutting threding and welding including transpotation of ring and supporting vehicle. Crew charges and cost of consumables etc complete including yield testing at that final depth with a minimum working of compressor for 1 hour (excluding cost of casing pipes,collars, and cap. etc ) ii) Up to 50.00 to 100.00 mtrs ---- as per directions of engineer in charge of work.

Sinking the Bore well of the 150mm dia clear using super fast hydrolic ring of capacity 250PSIG & above 900CFM& above in all strata including over burden up to 20mm. Fixing of casing pipes ,collears and cap with ncessory cutting threding and welding including transpotation of ring and supporting vehicle. Crew charges and cost of consumables etc complete including yield testing at that final depth with a minimum working of compressor for 1 hour (excluding cost of casing pipes,collars, and cap. etc ) iii) Up to 100.00 to 150.00 mtrs ---- as per directions of engineer in charge of work.

KSRB13-8.9 : Providing and fixing to wall, ceiling and floor high density polyethylene pipes 6.00 kgf/sq.cm working pressure 140mm outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications. Specification No.KBS 13.2.15.2 / 13.9 ---- as per directions of engineer in charge of work.

KSRB13-3.1: Providing and fixing in trenches galvanised / mild steel tubes (medium grade) 15mm dia nominal bore with all fittings ( earth work in trenches to be measured and paid for separately ) including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications. Specification No.KBS 13.2.14 / 13.6 ---- as per directions of engineer in charge of work.

Providing & fixing Gun metal wheel valve confirming to IS specification of approved quality and make as per directions with all lead & lift. ---- as per directions of engineer in charge of work.

Providing & Fixing MS cap. ---- as per directions of engineer in charge of work.

Supplying and Delivery at Site 5 HP 12 Stage Submersible Pump set of approved make ISI with Motor. Suitable for operation of 3 Phase 50 HZ 230Volts A.C supply fitted with required accessories complete as per the approved rate Make - Make:Kirloskar/Calama/Lubi/Atlanta/Texmo/Suguna and as per the directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying push button operated direct online starter with an antiweld silver cadmium oxide contactor with replaceable fixed and moving contacts and bimetallic thermal overload relay help in anticorrossion treated sheet steel or iron clad closure and fixing the same to suitable capacity wires for 400/440 volts 3 phase motor/single phase motor. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying and fixing single phase preventer using necessary wires over an existing panel board sutable for motor up to 20 HP capacity. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying, fixing and wiring heavy duty low voltage capaciters confurming to IS 2834 , 3 Phase 400/440 volts grade . For power factor improvement of rotating machinery. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220 V AC 50 HZ 12 / 24 v DC. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying , fixing and wiring 0 to 600 Volts 96 x96 mm AC Voltmeter on exisiting panel / wood board. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying fixing and wiring rotary selector switch sutable for Voltmeter. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying and flush mounting teak wooden box without front plank, made of not less than 12mm thick wood, after due groove cutting, necessary masonry patch work complete. 12x"12"x3" (300x300x76mm). Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Gate Valve : Supplying and Delivery of brand new approved ISI make 50mm bronze metal Gate Value as per the relevant IS Specifications. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Non-return Valve : supplying and Delivery of brand new approved ISI make 50mm bronze metal Non-return Value as per the relevant IS Specifications. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying and drawing 3 core flat PVC sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper conductor confirmining to table 3 class 5 of IS:8130-1984 and virgin grade PVC insulation and sheathed suitable for working voltage upto 1100Volts. c) 4Sqmm of 56strands 0.3mm dia. Make - Group "A" materials and as per the directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying and Delivery site brand new Tata "B" Class OK Zenith/Prakash best 'C' Class make G.I. Pipe with required specials confirming to IS 1239/Part. I/1979 with amendmant No.1.6 size 50mm. Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Supplying of LT UG cable having aluminium conductor PVC insulated, sheathed, galvanised, steel wire/steel strip (except 2CX10Sqmm wire armoured) 1.1 KV class. confirming to IS 3975:1990 (No of strip indicated in GTP) & extruded PVC outer shethed armoured cable with specified IS-1554 part-1:1988 & confirming to GTP Using - Group "A" materials and as per the specification & directions of Engineer in charge of the work. 1) 4 core 16 sqmm ---- as per directions of engineer in charge of work.

Labour charges for laying of 1.1 KV class UG cable when supplied agency in existing trench GI pipe / stoneware pipe / on wall / on pole as required. In exixting trench/duct. 1)6 sqmm to 16 sqmm, As per the directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. In soil (ordinary) ---- as per directions of engineer in charge of work.

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia. ---- as per directions of engineer in charge of work.

Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers. I) GI Wire c) 8swg ---- as per directions of engineer in charge of work.

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required. 3) 5-32Amps TPN Make - Group "A" materials and as per the directions of Engineer in charge of the work. ---- as per directions of engineer in charge of work.

"Supplying of Open well Mono sub pump set 3 HP,21 stage suitable for operation on 230 volts 2880 RPM Three phase AC supply Make- Using group ""A"" materials. And as per the directions of engineer incharge of the work. ---- as per directions of engineer in charge of work.