Karnataka Slum Development Board Tender

code04 - KSRB 5.2: Providing and constructing granite/trap/basalt size stone masonry in foundation with cement mortar, stone hammered dressed in courses not less than 20 cms high, bond stones at 2m. apart in each course including cost of materials, labour, curing complete as per specifications. KBS 6.1.13 KSRB 5.2-3 do cement mortar 1:6 (PWD SR 2023-24, Volume-1 Item No. 2.2.1. Page No.61)

code05 - KSRB 4.2.2: Providing and laying in position reinforced cement concrete of Design Mix M20 with OPC 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to 15 9103-1999 reafirmed- 2008, machine mixed, concrete Inid in layers not exceeding 15 cms thick, vibrated for all works in 5 foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnspillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc. including cost of all materials, labour, HOM curing, complete but excluding cost of reinforcement as per specifications. Specification No. (PWD SR 2023-24, Volume-1 Item No. 2.1.2, Page No.62&63)

code06 - KSRB 2.5: Earthwork excavation in all soil deposits and filling sides of foundation upto plinth in layers not exceeding 20cms. in depth, compacting each deposited layer by ramming after watering with all lead and lift including cost of all labour complete as per specifications. (PWD SR 2023- 24, Volume-I Item No. 1.11, Page No.35)

code07 - Providing and constructing load bearing wall with solid concrete blocks having block density not less than 1800kg/m3 having a minimum average compressive strength of 5.00 N/mm2 confirming to IS 2185 (Part 1):2005 and constructed with CM 1:4, as per 15 2572:2005 including cost of all materials labour charges, scaffolding, curing, hire charges of machineries etc., complete as per specifications. KBS No.5.4 do with solid concrete blocks of size 400x150x200mm (PWD SR 2023-24, Volume-II Item No. 6.33, Page No.17)

code08 - Providing and fixing machine moulded aluminium covering/Roof covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia, at a staggered pitch of 8 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge: Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) including cost of materials, labour, usage charges of machinery complete as per specifications.11.41.2 (PWD SR 2023-24, Volume-II Item No. 11.41.2, Page No.91)

code09 - KSRB15-3: Providing 15mm thick cement plaster in single coat with cement mortar to brick masonry including rounding off corners wherever required smooth rendering. Providing and 9 removing scaffolding, including cost of materials, labour, curing complete as per specifications. KSRB15-3.6do cement mortar 1:6 (PWD SR 2023-24, Volume-II Item No. 8.2.2, Page No.41)

code10 - KSRB15-3: Providing 15mm thick cement plaster in single coat with cement mortar to brick masonry including rounding off corners wherever required smooth rendering. Providing and 10 removing scaffolding, including cost of materials, labour, curing complete as per specifications KSRB15-3.6do cement mortar 1:6 (PWD SR 2023-24, Volume-II Item No. 8.2.2, Page

code11 - Providing and laying Cement concrete flooring 40 mm thick with 20 mm nominal size stone aggregate using 1:2:4 (1 cement: 2 coarse sand 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry complete. (PWD SR 2023-24, Volume-II Item No.- 9.1, Page No.59)

code12 - KSRB 15-14.1: Providing and applying two coats with oil bound washable distemper approved brand and shade on wall surface including priming cost with distemper primer after 12 throughly brooming the surface free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. (PWD SR 2023-24, Volume-II Item No. 8.25, Page No.45)

code13 - Exterior Wall Waterproof Coating Providing and Applying high build Acrylate Copolymers-based elastomeric waterproof coating for external wall, parapet & Chajja, which is single component, cold applied, acrylic emultion polymer. Applycoat lat coat with 10% dilution water and 2nd coat without dilution 0.271/m2 in 2 coats to achieve DFT of 110 microna, The material having followed technical properties: Attains hairline crack bridging up to 1 mm, Elongation of 120 % as per 13 ASTMD 412, Tensile strength 1.50 Mpa per ASTM D 412, Pull off adhesion, 1.5Mpa as per ASTM D4541, including priming the surface with 1 coat diluted with water in the ratio 21 spreading 0.125 L/m2 as self-priming coat. The finished cost to include surface preparation, making coving at Junction, treatment of cracks completely as per specification (PWD SR 2023-24, Volume-11 Item No. 15.15, Page No. 153)

code14 - Providing and fixing white vitreous china clay, water closet Indain type (Squatting pan) of size 580 mm with footrests 100 mm S or P trap (approved make) cutting and making good the wall and floor wherever required including cost of materials labour complete as per specfication (PWD SR 2023-24, Volume-II Item No. 14.1.1, Page No.131)

code15 - SOLID PANEL PVC DOOR SHUTTER Providing & fixing 30mm thick factory made rigid foam Panelled Door Shutters made from M.S. tube of 19 gauge thickness, size 19x19mm fro styles and 15x15mm for top & bottom rails, covered with heat moulded PVC channel of 5mm thick sheet & 30 x 50mm wide to form styles & 5mm thick & 75mm wide PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick 20mm wide PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet fitted in the M.S. Frame, Sealed to the styles & rails with 5x30mm PVC sheet beading on either side & joined together with solvent cement adhesive etc.. Complete as per manufacturers specification & direction of Engineerin-charge fixed to frames with 3 nos of 75 m.m Aluminium hinges (PWD SR 2023-24, Volume-II Item No. 12.53, Page No.104)

code16 - SOLID PVC DOOR FRAME Providing & fixing factory made PVC Door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners & jointed 2 No.s of 150mm long brackets of 15x15mm M.S Square tube, the entire door frame to be reinforced with 19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to the wall using M.S. Screws of 65/80mm size complete as per manufacturers specification & direction of Engineer-in-charge. (PWD SR 2023-24, Volume-II Item No. 12.54, Page No.104)

code17 - Constructing brick masonry inspection chamber 455x610mm, and 450mm depth, (clear inside dimension) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 17 kg) R.C.C. top slab with cement concrete M 15 with 20mm and downsize granite metal, foundation concrete M 5 with 40mm and downsize granite metal inside plastering 12mm thick with cement mortar 1:3, finish smooth with a floating coat of cement on walls and bed concrete complete as per standard design including cost of materials, labour charges, curing complete as per specifications. (PWD SR 2023-24, Volume-II Item No. 13.63, Page No.126)

code18 - Constructing brick masonry inspection chamber 600x600mm and 460mm depth, (clear inside dimension) for single pipeline, using table moulded non-modular bricks of class designation 50 in cement mortar 1:5, C.I cover withframe (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 18 kg) R.C.C. top slab with cement concrete M 15 with 20mm and downsize granite metal, foundation concrete M 5 with 40mm and downsize granite metal inside plastering 12mm thick with cement mortar 1:3, finish smooth with a floating coat of cement on walls and bed concrete complete as per standard design including cost of materials, labour charges, curing complete as per specifications. (PWD SR 2023-24, Volume-II Item No. 13.54, Page No.126

code19 - Providing and fixing unplasticised PVC pipes 10.00 kg/sq.cm working pressure chemp plast/Wavin or equivalent make with pipe fittings, clips, making good the floor, including cost of all materials, labour charges, HOM of equipment and testing complete as per specifications -do- with 100mm outer dia (PWD SR 2023-24, Volume-II Item No. 13.50.9, Page No.125)

code20 - Providing and fixing unplasticised PVC pipes 10.00 kg/sq.cm working pressure chemp plast/Wavin or equivalent make with pipe fittings, clips, making good the floor, including cost of all materials, labour charges, HOM of equipment and testing complete as per specifications -do- with 150mm outer dia (PWD SR 2023-24, Volume-II Item No. 13.50.10, Page No.125)

code21 - Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded 21 fittings including fixing the pipe with clamp at 1.00 mtr spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete. (internal work exposed on wall) 32mm nominal OD pipes (PWD SR 2023-24, Volume-II Item No. 13.31.4, Page No.122

code22 - Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded 22 fittings including fixing the pipe with clamp at 1.00 mtr spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete. (internal work exposed on wall) 25mm nominal OD pipes (PWD SR 2023-24, Volume-II Item No. 13.32.3, Page No.122

code23 - Providing and fixing in position brass bib cock of approved quality 15mm nominal bore including 23 cost of all materials, labour and HOM of equipments with all leads complete as per specifications. do 25 mm dia nominal bore (PWD SR 2023-24, Volume-11 Item No. 13.2.1

code24 - Providing and fixing PVC (S W.R) Nahani Trap 10cms x 10cms with all 24 fitting arrangements & all necessary accessories complete (PWD SR 2023-24, Volume-II Item No. 13.59, Page No.127

code25 - Providing and placing on terrace, polyethylene water storage tanks as per IS 12701: 1996 with manhole lid and suitable locking arrangements, making holes of suitable diameter for inlet, outlet 25 and over flow pipes, including cost of all materials, labour, transport charges, HOM of equipments and testing complete as per specifications. (For 1000 litre capacity) (PWD SR 2023-24, Volume-II Item No. 13.34. Page No.123)

code26 - Providing and fixing in position brass gate valve with C.I wheel of approved quality (screwed end) 15mm nominal bore including cost of all materials, labour and HOM of equipments with all leads 26 complete as per specifications.. do 25 mm dia nominal bore (PWD SR 2023-24, Volume-11 Item

code27 - Providing and fixing in position in cement concrete 1:3:6 Steel glazed windows and ventilators side hung/top hung 2/3 openable 1/3 fixed as per approved drawings using Z angles of 25x46x3mm. Weighing 1.419 Kg/m both for outer and inner frames and central mullion section of size 25x46x3mm. Weighing 2.28Kg/m duly providing T section 19x19x3mm weighing 0.839Kg/m for glazing of windows not more than 34 cms. C/C including providing and fixing 4mm. Thick reeded glass with teakwood beading of required size, all sections should confirm to IS 7452:1990, 4nos. of holdfasts of approved size, section should be cut to length welded and electrically grinded subdividing frames of unit shall be tenonned and revetted into the frames electrically. All the steel surface shall be througly cleaned free of rust and painted with one coat of anti-corosive paint and fininshing with two caats of ready mix paint of approved colour and make including cost of materials, fixtures, labour and HOM of machinery complete as per specifications. (PWD SR 2023- 24, Volume-II Item No. 11.10.1, Page No.79)