Karnataka Rural Road Development Agency Tender

Construction of unlined surface drains of average cross sectional area 0.40 sqm in soil to specified lines, grade, levels & dimensions Excavated material to be used in embankment as per Technical Specifiacation Clause 307 by Mechnical means. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Excavation in Soil with Dozer ,Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. etc, Complete with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of Embankment with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of granular sub-base by providing well graded material as per Clause 401, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading III Material .with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work .

Available Grading 2 material: Providing, laying, Spreading and compacting available stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thikness, hand packing, rolling with three wheel 80-100 KN static roller in stages to proper grade and camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per technical specification clause 405. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. By Mechanical Means as per the directions of the Engineer incharge of the work.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming ,Crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. By Mechanical Means as per the directions of the Engineer incharge of the work.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. By Mechanical Means as per the directions of the Engineer incharge of the work

Providing and applying primer coat with bitumen emulsion (SS-1) of low porosity on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0kg/sqm using mechanical means as per Techinical Specification Clause 502 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

20mm thick Open-Graded Premix Carpet8% by weight of bitumen Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates by using (S-65) penetrated grade bitumen with addition of processed waste plastic of upto 8% replaced by weight of bitumen to required layer, grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.( Rates inclusive of Supervision at site from waste plastic supplier) With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in suitable plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case II By mechanical Means using (S-65) Bitumen with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying seal coat Type B sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using as per Technical specification Clause 510. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. and as per the directions of the Engineer-in-charge of work. By Mechanical Means, Case II : TYPE B,using Bitumen (S-65)

Providing Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work Ordinary Kilometre stone(precast)

Providing Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 5th Kilometre stone(precast)

Providing Reinforced cement concrete M15 grade kilometre stone/local stone design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 200 Mtr stone (precast)

Providing and fixing Logo board of PMGSY at Starting point Providing and fixing Logo board as per specifications and drawing Two ACP sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x 5mm size on back and on the edges. the Top and bottom plate will be welded/bolted to 1 nos 75x75x6 mm square Hallow section dully embedded in cement concrete M15 Grade of 600*600mm 450 mm below ground level Retro reflecting sheet as per IRC 67 made of encapsulated lens type reflective sheeting vide clause 1701.3.8.1 fixed over aluminium sheeting All sections of steel tube will be pained with primer and two coats of epox paint as per drawing.Retro reflecting sheet as per IRC 67 clause 1701.3.8.1 -Class A TYPE-I with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and Fixing 'Logo Board ' of PMGSY at Intermediate Point: Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and Fixing Citizen information Board-A Providing and fixing typical citizen information Board-A as per specification and drawing. Two ACP sheet of 4 mm thick having minimum 0.25 mm thick aluminium skin both sides and fixed over aback support MS plate of 5 mm thick. Supported on frame post of 2 nos of MS Square hallow section 75 mm*75* 6mm which is duly embedded in cement concrete M 20 grade of 600*600mm* 750 mm, 600 mm below ground level all MS will be stove enamelled on both the sides. All sections of framed posts, M.S. sheet and stell tubes will be painted with primer and 2 quotes of epox paint as per drawing etc Retro reflecting sheet as per IRC 67 fixed over a 2 no.s of aluminium composit material (ACP) sheeting of size 900*750mm of 4mm thick duly bolted/reveted with MS place of 5 mm thick on back side of ACP sheet. Including cost & conveyance of all meterial equipment, mechinary and labour with all lead & lift loading charges. Necessary satisfactory completion of work as by directed by engineering in charge (i). For warrantee & durablety the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (II). A reference No. along with the month end year of installation should be placed on the back of a sign in a contrasting colour or by stamping in character not exceeding 50 mm in height. with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge.

Providing and Fixing “Maintenance information Board”Providing and fixing typical maintenance information Board as per specification and drawing. ACP sheet of 3 mm thick having minimum 0.25 mm thick aluminium skin both sides and fixed over a back support MS plate of 5 mm thick. Supported on frame post of 2 nos of MS Square hallow section 75mm*75* 6mm which is duly embedded in cement concrete M 20 grade of 600*600mm* 750 mm, 600 mm below ground level. All MS will be stove enamelled on both the sides. All sections of framed posts, M.S. sheet and stell tubes will be painted with primer and 2 quotes of epoxy paint as per drawing etc. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. i)The board will be a composite unit consisting of three plates of Aluminium Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most platewill be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mmx 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart centre to centre. The top of the middle plate will be flushed with the top of 75 mm dia medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. (ii) The lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 essages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing. (iii) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (iv) A reference number along with the month and year of installation should be placed on the back of a sign in a contrasting colour or by stamping in characters not exceeding 50 mm in height.485777/2019/Dir(Tech) . with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work.

Providing and laying reinforced CEMENT CONCRETE PIPE NP2 450MM DIA for culverts including pointing ends, and fixing collars with cement mortar 1:2 including cost of all materials, labour, curing complete as per specifications. Specifications. No. KSRB 1000, 2300 MORT & H Specification No.1000 / 2300 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing road humps for the entire formation width, using bituminous premix materials and heavy duty cobble stones 60 mm thick, having road hump dimension of 1.00 mtr (width) X 0.15 mtr (height) rectangular sections and ramp on either side of road hump of 0.85 mtr (wide), including providing WBM (2 layers) for shoulder portion 1.7mts in length on either side, completing with road marking paint with applied thermoplastic compound with reflecting glass beeds on bituminous surface and providing 2 Nos. retro reflective traffic signs as per IRC SP 67-2010 (for details refer IRC 99-1988). For single lane for formation width of 7.50 mtr using SDBC mix material. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Road Marking with Hot Applied Thermoplastic Compound with Reflectrising Glass Beads on Bituminous Surface:- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No. 803 --- With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Road Studs/ Road markers: Supply and installation of Moulded Shank Raised pavement markers made of polycarbonate and ABS (Acrylonitrile Butadiene Stryrene) moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to Specification of Category A of MORTH Circular no: RW/NH/33023/10-97-DO III Dt 11/06/1997. The height, width, and length shall not exceed 50 mm, 100 mm and 102 mm and with minimum reflective area of 13 sqcm on each side and slope to base shall be 35 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19mm and height not less than 30 mm) from the body is to be a minimum value of 500 kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufactures recommendation . With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Retro-Reflectorised Traffic Signs :- Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over Aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing complete as per specifications. 600 MM Equivelateral –Type XI with all lead and lifts, loading and un-loading charges, cost of labour, HOM charges of all machineries, incidental and equipment charges, etc., complete as per the directions of the Engineer incharge of the work

Retro-Reflectorised Traffic Signs :- Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 800.1.3, fixed over Aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing complete as per specifications. 600mm Circle Type XI

Retro-Reflectorised Traffic Signs :- Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 800.1.3, fixed over Aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing complete as per specifications. 600X450mm Type-XI

Manufacturing,Supply and installation of Retro- reflective Hazard Marker signbaords made out of cube corner micro prismatic grade sheeting confirming to Type XI standards of IRC:67:2012 & ASTM D 4956-09 specification & fixed over 4 mm thick Aluminium Composite Panel sheet having minimum 0.3mm thick aluminum skin on both sides & fixed over back support frame of 25x25x 3mm MS angle frame. Supported on round pipe post of 1.5m height and gouted 60cm below ground level. The sign post should be painted with one coat of red oxide paint and two coats of synthetic enamel paint of black and firmly fixed to the ground by means of foundation with M20 grade cement, concrete foundation size of 45x 45x60cm including cost & conveyance of all materials, equipment,machinery & Labour with all leads and lifts,Loading charges necessary for satisfactory completion of the work as directed by engineer Hazard Board for Tank Bundincharge.With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Direction and Place Identification Signs upto 0.9sqm Size Board: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide Clause 801.3, fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9sqm supported on a mild steel single angle iron post 75x75x6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45x45x60cm, 60cm below ground level as per approved drawing. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Earth work excavation in all kinds of soils for foundation of structures as per drawing and technical specifications, including setting out, providing shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and filling back with approved material including cost of all materials, labour,HOM complete as per specifications. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Plain cement concrete M10 mix with crushed stone aggregate 40mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing including cost of materials, labour, HOM complete as per specifications MORTH Specification No 408. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Refilling available earth around pipe lines, cables in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering including cost of all labour complete as per specifications. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Metal Beam Crash Barrier:- Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 800.10 complete as per specifications. Excluding cost of earth work excavation and pcc for fixing. A. Type- A, "W" With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge.

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work as per Technical Specification Clause 202.Cement concrete

Removing all types of Hume pipes and stacking including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work (Above 600 mm to 900 mm dia Hume pipe)

Earthwork in excavation for structures as per drawing and technical specification Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal dressing of sides and bottom and backfilling in trenches with excavated suitable material. In ordinary Soil. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and Filling in foundation with granite / trap broken metal 100mm. and down size, with approved sand including hand packing, ramming, watering, including cost of all materials and labour with all lead and lift. complete as per specifications.specification.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.7 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and constructing plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203.P.C.C. grade M-10, Nominal mix 1:3:6 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing & Laying concrete cradle bedding with M15 Grade Cement Concrete as per Clause 1105(i) with all lead and lifts, loading and unloading charges, cost of all materials & conveyance, labour, equipments etc., complete as per detailed specification and direction of the Engineer-in-charge.

Providing and constructing Plain/reinforced cement concrete PCC grade M-15 nominal mix (1:2.5:5) in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying reinforced cement concrete pipe NP3 class for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 1000 mm dia single row

Providing and laying reinforced cement concrete pipe NP3 class for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work 750mm dia single row

Providing and laying curtain walls complete as per drawing and technical specification Clause 1304.Cement Concrete grade M-10. Complete with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying pitching on slopes laid over prepared filter media as perdrawing and technical specifications clause 1302 Stone/Boulder with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying reinforced cement concrete in substurcture as per drawing and technical specifications Clauses 802, 804, 805, 806, 807, 1202 & 1204 RCC Grade M-25, Cement Concrete. with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 Earth filling (For marshy soil) with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Providing and laying reinforced CEMENT CONCRETE IN SUPERSTRUCTURE as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 R.C.C M 25 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work

Providing and constructing Plain / reinforced CEMENT CONCRETE IN SUBSTRUCTURE complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 PCC GRADE M20 NOMINAL MIX 1:2:4 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

Routine maintenance after completion of construction work For 1st Year

Routine maintenance after completion of construction work For 2nd Year

Routine maintenance after completion of construction work For 3rd Year

Routine maintenance after completion of construction work For 4th Year

Routine maintenance after completion of construction work For 5th Year

6th Year Renewal after maintenance:Clearing & grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings & trees of girth upto 300mm, removal of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable material to be used or auctioned, including removal & disposal of top organic soil not exceeding 150mm in thickness as per technical specification clause 201.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work In area of non thorny jungle. By mechanical means.

6th Year Renewal after maintenance:Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance: Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 13.2 mm to 0.9 mm (Type - B) aggregates using penetration grade bitumen (with addition of processed waste plastic of upto 8% replaced by weight of bitumen) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in suitable plant, laying and rolling with a three wheel 8-10 KN static roller and finishing to required level and grades as per Technical Specification Clause 509 By Mechanical means,using Bitumen (S-65) (Rates inclusive of Supervision at site from waste plastic Supplier) With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Surface Drains in Soil : Construction of unline surface dressing of average cross sectional area 0.40 Sqm in soil to specified lines,grades level and dimension. Excavated material to be used in embkmant as per technical specification clause 307 . Mechnical Means With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Boundary Pillars Reinforced cement concrete M 15 grade boundary pillars/local stone of standard design as per IRC : 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Road Marking with Hot Applied Thermoplastic Compound with Reflectrising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per specifications. MORTH Specification No. 803 With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Maintenance of Culverts Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair,repair stocracks, parapet wall and protection work as per drawing and technical specification Clause 1908. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Maintenance of Culverts Slab type Maintenance of Slab type Culverts by way of clearing, Cleaning, Erosion repair, repair stocracks, parapet walls and Protection works as perdrawing and technical specification Clasue 1908. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Maintenance of Causeway by way of minor Surface repairs, replacing Guide Posts, repair of flood gauges, removal of debris, providing boulders and protection work and painting as per technical specification Clause 1909. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work

6th Year Renewal after maintenance:Maintenance of Road Signs : Maintenance of road signs by way of cleaning and repainting of mandatory/requlatory/cautionary/informatory and place identifications sign board as per drawings and technical specification Clause 1910. With all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer incharge of the work