Jungle Lodges And Resorts Limited Tender

Removing and fixing shutters (panelled or glazed) to doors, windows, ventilators and cupboards. including cost of materials, labour, HOM complete as per specifications.

KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of machinery complete as per specifications. Specification No. KBS 4.6.3 - TMT bars Fe 500, INo.4.46.2 of SR 2018-19

Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes jointing of pipes and fittings with one step solvent cement, trenching, refilling & testing of joints complete. (external work). Cold water supply -20mm nominal OD pipes

SS SINGLE SINK UNIT16 GA SS Sunken Top with Rear Splash.Top secured to MS angle frame, 16 GA SS Sink Size : 450mm x 450 mm x 300 mm deep., 4 Nos.16 GA SS �38 mm tubular legs with. adj.nylon bullet feet.

KSRB 15-18.2: Provoding & applying enamel metal paint two coats (excluding priming coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other foreign matters, including cost of material, labour, complete as per specifications. Item No.15.74 SR 2018-19)

Point wiring using Copper wire without switch.Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet.Long point above 6Mtr up to 10Mtr from tapping point to out let via switch box

Supplying Fxing approved make C.P. toilet paper holder 150 x 150 mm complete. ( Jaguar make or Equivalent ).

KSRB 13.8 Providing and fixing to wall, ceiling and floor, medium density polyethylene pipes 6.00 kgs/sq.cm working pressure of outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor including cost of all materials, labour charges, HOM and testing complete as per specifications for internal water supply connection complete as per directions of Engineer-in - charge-75mm dia

Supplying and drawing PVC insulated gas injected physical foam jelly flooded co-axial TV cable.RG-6.

Blowers with motar-Providing ,installation and testing centrifugal blower direct driven by 7HP(LLS Model)1440rpm 2HP,ISI Make motor best make of approved brand kirloskar or Equivalent as per the direction of engineer in charge

KSRB13-6.1-1 : Providing and fixing in position brass bib cock of approved quality 15mm nominal bore including cost of all materials, labour and HOM of equipments with all leads complete as per specifications. Specification No.KBS 13.2.2 / 13.3

CCTV CAMERAS-Supplying, installation, testing and commissioning of Wireless CCTV cameras as per direction of Architect and Engineer in charge .The prices should include the necessary mounts and brackets.

Removing of existing old or broken Water closet Indian / Eurpoean and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

SS WALL SHELVING Constructed of 16 SWG (304) SS top, double beaded on all sides and secured to 38X38X3 mm SS angle welded framework. Sink size 450X450X350 deep integral with top sheet - check the drawing for position of the Sink. In the center 50 mm dia BSP drain coupling, hot and cold water faucet, deck mounted. Splash back 150 mm on rear / side.(AS PER LAYOUT DRAWING). 18 SWG (304) SS bottom shelf starting at 150 mm. Four numbers SS tubular legs with adjustable bullet feet.

Removing wall paneling I false ceiling I wooden partition I aluminium partition, stacking it with all cost and conveyance labour for all items of work, HOM of equipment etc., complete as per specification

Supplying and fixing superior quality 10-12 Module modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box.

SS WORK TABLE WITH SINK Constructed of 16 SWG SS top, double beaded on all sides and secured to 38X38X3 mmMS angle welded framework. Bowl size 450X450X250 deep integral with top sheet - check the drawing for position of the bowl. In the center 50 mm dia BSP drain coupling,. Splash back 150 mm on rear / side.(AS PER DRAWING). 18 SWG ) SS bottom shelf starting at 150 mm. Four numbers SS tubular legs with adjustable bullet feet.

Removing of existing old or broken Plumbing fixtures and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

Removing and fixing frames (panelled or glazed) to doors, windows, ventilators and cupboards. including cost of materials, labour, HOM complete as per specifications.

KSRB 11-11.2 : Providing and fixing white vitreous china clay, flat back wash basin size 630x450mm with a single 15mm C.P brass pillar tap with C.I / M.S brackets, 32 mm C.P. brass waste of standard pattern, painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour complete as per specifications. Specification No. KBS 11

KSRB 9-27.1 : Fixing of door frame in an existing opening including embeeding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size granite metal painting two coats of coal tar to sides of frame, making good the damages to walls and floor as required and disposal of the debries with lead upto 50 m. including cost of materials, labour charges, complete as per specifications.

Provinding and constructing non load bearing wall with Light Weight Concrete (Autoclaved areated concrete) Blocks confirming to IS:2185 (part-3) 1984 and IS 6441-1972 of compressive strength of 3.0N/sq mm with a thin layer of polymer based jointing solvent for super structure with neccesary scaffolding, curing including cost of all materials, labour, lead& lift etc, complete as per specifications. - with 600x200x100mm size Blocks

KSRB 13.8 Providing and fixing to wall, ceiling and floor, medium density polyethylene pipes 6.00 kgs/sq.cm working pressure of outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor including cost of all materials, labour charges, HOM and testing complete as per specifications for internal water supply connection complete as per directions of Engineer-in - charge-110mm dia

Supplying, fixing, testing and commissioning of CP health faucet with 8mm dia and 1200mm long flexible tube with wall hook etc., complete as directed by the Engineer in charge. ( Jaguar make or Equivalent ).

Providing and fixing of Integra-X Split heat pump of capacity 500 L Including all works etc as per direction of architect and Engineer in charge(4 Nos)

TANDOOR (CHARCOL) - The framework should be made of 25 x 25 SWG 14 boxed welded angles, and should be angle reinforced on all sides and bottom and intermediate positions. Exterior of base reinforced with heavy gauge MS inverted channel framework on all sides and suitable to fix castors.OUTER BODY-18 gauge SS Sheets with 25mm thk Mineral Wool insulation all around. INNER BODY - 1mm thk GI Sheets. POT - Earthen Pot (Suitable Size). ASH OUTLET - Provide Insulated door on hinges & latch(Size 6”x6” opening).

PLATFORM TROLLEYS Unit to be constructed of SWG 16SS double beaded on all sides on 35X35X3 mm SS angle welded framework. SWG 16 SS, 1 � inch dia pipe handle fixed to body with SWG 14 SS angular support. Four numbers 150 mm dia all swivel heavy duty rubberized castors to take loads of 150 kgs. Two of the wheels to have locking arrangement. Rubber bumpers / guards.

Concealed Conduit System Supplying heavy gauge PVC conduit pipe 19/20mm dia 2mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary

Supplying heavy gauge PVC Conduit Pipe19/20dia 2mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary.

KSRRB 200-9. Clearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, by manual means, in area of thorney jungle, removal of stumps, disposal of unserviceable materials, stacking of serviceable materials labour charges complete as per specifications. MORTH / Chapter 2, I.No.18.12 SR 2018-19

Providing and fixing of Gyproc PVC False Ceiling on M.S. square tubes (18mm x 38mm x 18swg) frame at a distance of 450mm x 900mm center to center OR on G.I channel framework. The perimeter channel is fixed along with the wall, having a dimension of 25mm x 25mm x 20mm with a thinkness of 1mm � 0.3mm including cost of materials, labour, curing as per specifications. complete as per directions of Engineer-in - charge

SS PALLET ( Low Height Work Table) 16 GA SS �32 mm S.S. tubular pipe bracings provided an all Sides.Internal grid of 16 GA SS �25 mm mm vertical postion pipe at 90 - 100 mm spacing. 16 GA SS �25 mm S.S. tubular pipe bracings provided at all Sides. 4 Nos. 16 GA SS 304 Grade �38 mm tubular legs with. adj.nylon bullet feet.

Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes jointing of pipes and fittings with one step solvent cement, trenching, refilling & testing of joints complete. (external work) Cold water supply. - 15mm nominal OD pipes

Supplying and flush mounting 6Way powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall

Supplying and flush mounting 10-12 Way powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall

Supply and Installation of 2-way splitters in die cast Al.casing-Supply

KSRB 11-17-1 : Providing and fixing C.P. brass towel rail 600mm length, 20mm dia with C.P brackets, fixed to wooden cleats with C.P. brass screws including cost of materials, labour complete as per specifications.

Supplying and fixing of slim box fitting, made out of CRCA Sheet metal body with locking type holder completely wired. Excluding Ballast & Flouresent Tube

Supplying, installing, testing and commissioning of Diesel Generator set with following specifications. Power rating as per standard reference condition as per-BS 5514 / ISO 3046 / ISO 8528 & IS 1002 / ISO 3046 Generator set specifications. Engine: Diesel generating set are rated at 1500RPM and conform to ISO 8528 specifications. The engines are radiator cooled, four stroke and multi cylinder, conforming to ISO 3046. The scope of supply includes: Electrical starter motor 12V DC Battery charging alternator, Bosch fuel system with mechanical governor, A1 Class. Spin-on lube oil filter, Spin-on dual fuel filter with water separator, Turbocharger, Charge air cooler, Silencer (Hospital grade),Dry type air cleaner, Shutoff coil, Flywheel and flywheel housing, First fill of lube oil and coolant, Safety for low lube oil pressure, Safety for high water temperature, Permissible overload of 10% for one hour in 12 hours of operation Capacity of Fuel Tank: Fuel tank suitable for 8 hours of operation Alternator: Alternator is suitable for operation at 1500 RPM, 415 Volts, 0.8 pf (lag) suitable for 50 Hz, 3 phase, 4 wire systems, conforming toIS/IEC 60034-1. The Alternator is brushless type, screen protected, revolving field, self excited, self regulated through an AVR. The alternator shall have + 1.0 % Voltage regulation (max) in static conditions- IP: 23 protections with insulation class H Mounting arrangement: Engine and alternator are mounted on a common MS fabricated base frame with AVM pads. Control Panel: The control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for weather-proof and long lasting finish. The control panel consists of the following parts:- PS0500 Controller, Aluminium bus bars with suitable capacity within/outgoing terminals, Indicating lamps for ‘Load On’ and ‘Set Running’, Instrument fuses duly wired and ferruled, MCCB of suitable rating with overload and short circuit protections. Genset Controller: microprocessor based generator set monitoring and control system. The control provides a simple operator interface to the generator set, manual and remote start/ stop control, shutdown fault indication, and an LCD hour counter. The integration of all functions into a single control system provides enhanced reliability and performance compared to conventional generator set control systems. This control has been designed and tested to meet harsh environment in which gensets are typically applied. Features, Functions, protections 16 character x 2 line alphanumeric LCD display with LED Backlight. Operator interface, Provide a record of most recent fault conditions. Fault history stored in the control non volatile memory, Provide Alternator Data. Voltage (1 ph or 3 ph line to line and line to neutral voltage, Current (1 ph or 3 ph), kVA (3 ph and total), Frequency, Provide Engine Data, Starting battery voltage, Engine running hours, Engine Temp, Engine oil pressure, Control includes provision for Service adjustment and calibration of DG control functions, Voltage, frequency selection, Configurable input and output set up, Meter calibration, Engine controls, Power Start operates on 12 VDC batteries,- Auto start mode accepts a ground signal from remote devices to automatically start the DG set. The remote start will also wake up the control system from sleep mode. Engine Starting –The control system supports automatic engine starting, Primary and back up start disconnects are achieved by battery charging alternator feedback or main alternator output frequency. Controller provide configurable time delay of 0-300 secs to start after remote start signal and time delay of 0-600secs prior to shut down after stop signal. Sleep mode increase battery life. Configurable current settings from low to minimize current draw when genset is not working. Engine Protective functions include, Configurable alarm output, Emergency stop: Annunciated whenever an emergency stop signal is received by the control. Low lube oil pressure warning and Shutdown, High engine water temp warning / Shutdown, Low coolant temp warning, Sensor failure indication, Low and high battery voltage warning, Weak battery warning, Fail to start shut down, Cracking lockout: Control will not allow the starter to engage or to crank the running engine. Cyclic cranking: Configurable for the number of starting cycle, (1 to 7) and duration of crank and rest periods. Alternator Protective functions includes, - High and Low AC voltage shut down, Under and Over frequency shutdown / warning, Loss of sensing voltage input shut down. Acoustic enclosure: The acoustic enclosure shall be made of 1.6 mm thick CRCA sheets in suitable approved shade and a structural/ sheet metal base frame painted in black. The walls of the enclosure are insulated with fire retardant foam so as to comply with the 75dBA at 1 mtr sound levels specified by Ministry of Environment & Forest. The enclosure has the following features: Specially designed to meet stringent MOEF/ CPCB norms of 75dBA @ 1mtr at 75% load under free field conditions, Two point lifting for easy handling at customer site, Designed to have optimum serviceability, Air inlet louvers specially designed to operate at rated load made on special purpose CNC machines for consistency in quality and workmanship, Powder coated for long lasting service life and superior finish, With UV resistant powder coating, can withstand extreme environment, Use of special hardware for longer life, Insulation material meets exacting IS 8183 specifications for better sound attenuation, Flush styling - no projections, Fluid drains for lube oil and fuel, Fuel filling point inside the enclosure-180Kva/144kw

INGREDIENT BINS WITH WHEELS (Cap:50 Kgs) Unit to be made of 18 GA SS body & hinded flip lid with handle. All ends shall be closed, welded, ground and polished smooth. 4 nos. �100 x 32 mm noise free rubber swivel type castors, castors fitted to channel frame work.

Labour charges for laying of 6 sqmm to 16 sqmm 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In existing trench/duct.

Providing & Fixing of Hold fast MS to wall including cost of materials, labour charges, complete as per specifications.Providing & Fixing of corner beads of wooden door frame to wall including cost of materials, labour charges, complete as per specifications.

Removing of existing old Electricals wires and Cables , stacking and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

Supplying and fixing of 6Amps three way modular switch/ Socket/stepped electronic fan regulator/ dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of stepped fan regulator on existing modular switch plate as per IS 3854 and IS 1293

Supplying and flush mounting 1-3Way powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 12 mm dia

Removing of existing old Sanitary and plumbing pipelines, stacking and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

Supplying, fixing, testing and commissioning of two - in - one wall mixer shower assembly unit consisting of the following in the shower area: Standard make confirming to ISI standards,Model as per attached photo catalogue and as per instruction of engineer incharge. Single Lever Wall Mixer with Hand Shower ( Jaguar make or Equivalent ).

Wiring for lighting/power circuit using 4 sqmm of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments.

TANDORI WORK ONE UNDERSHELVES25 mm thick granite top sitting on SWG 16 SS channel frame with SWG 12 SS corner pieces.SWG 18 SS shelf at 150 mm from FFL double beaded on all sides. 38 mm dia SWG 16 SS pipe legs with adjustable feet.

Wiring for lighting/power circuit using 1.5 sqmm of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments.

Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, 50 cycles. Single phase AC supply conforming to ISS-374-1979 and with double ball bearing system. 48" Sweep (1200mm)

2 DOOR WORK TOP REFRIGERATOR WITH 2 OHS16 GA SSTop.Top secured to MS angle frame Body shall be of full SS construction with interior and the exterior of 20 G SS The inner wall will be suitably insulated with PUF. It should have 2 doors, constructed of 18 G SS with a locking Facility.The unit will have 4 nos. SS shelves per door . It should be fitted with digital temperature indicator, control switches and indicator lights.The equipment should be able to maintain a Temperature of +0˚C to + 6˚C. The unit shall be provided with a SS drip tray . Forced draft cooling.The compressor make from Emerson/Copeland/ Kirlosker .COMPRESSOR LOCATION AS PER DRAWING 2 Nos.18 GA SS )Over head shelves with 300mm width.Shelf supported with 25mm Dia Pipe Legs & Fittings 4 Nos. 16 GA SS 3 Ø40 mm tubular legs with. adj.nylon bullet feet. 1KW/16A/1∅ SUPPLY Ht @ 450mm AFFL

Providing and fixing Vitrified glazed tiles of approved make, quality & colour of size 600 x 600 x 10mm thick fixed on bed of 12mm thick cement mortar for flooring, skirting and jointed with neat cement slurry mixed with pigment to mach shade of tiles, including providing spacers at required interval and removing stains, including cost of all mateirals, mortar, labour, etc , Complete as per specification.

Supplying and fixing of TV/ Telephone modular switch/ Socket/stepped electronic fan regulator/ dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of 6Amps two way modular switch/ Socket/stepped electronic fan regulator/ dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293

KSRB 11-15.3 : Providing and fixing 453x357mm dia rectangular shape mirror with plastic moulded frame of approved make and shade with 6mm thick hard board backing including cost of materials, labour complete as per specifications.

KSRB13-6.2-1 : Providing and fixing in position brass stop cock of approved quality 15mm nominal bore including cost of all materials, labour and HOM of equipments with all leads complete as per specifications. Specification No.KBS 13.2.2 / 13.3

KSRB 14-17.2 : Providing skirting, dado, rises of steps with colour glazed tiles on 10mm thick cement plaster 1:3 and jointed with white cement slurry over rough plaster surface ( excluding cost of rough plastered surface which should be measured and paid separately) using glazed tiles of approved make and size including cost of materials, labour, complete as per specifications. Specification No.KBS 14.16, 14.17 - Colour glazed tiles 30x45 cms 6mm thick with border of size 30 x 10 cms.

KSRB 4-1.3 : Providing and laying in position plain cement concrete of mix 1:4:8 with OPC cement @ 180kgs, with 40mm and down size graded granite metal coarse aggregates @0.85cum and fine aggregates @ 0.57cum machine mixed, machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation, including cost of all materials, labour, HOM of machinery, curing complete as per specifications. Specification No. KBS 4.1, 4.2

Providing & fixing of 5.5mm thick plain float glass with multi chambered uPVC sections with TPv gaskets including all required hardware fittings etc as per archirect direction and Engineer in charge.

SOILED DISH LANDING TABLE WITH CHUTE - Constructed of 16 SWG SS top, double beaded on all sides and secured to welded SS angle frame. � inch raised marine edges. Waste chute - One no. 6 inch diameter with rubber edges on left (confirm with the drawing) hand side 175 mm from the side edges. 25 mm dia drain outlet on the left hand side corner connected to waste outlet with lever handle. Four numbers, SS tubular legs with adjustable bullet feet. Side and rear cross bracing support to give a clear front to move in waste bin under the table.

Supplying heavy gauge PVC Conduit Pipe 25mm dia 2mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary.

Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes jointing of pipes and fittings with one step solvent cement, trenching, refilling & testing of joints complete. (external work). Hot water supply -20mm nominal OD pipes

Supplying And Fixing Metal Fan Box with Round Hook.

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete In soil (ordinary)(As per Civil SR KSRB I-2, P-7)

Supplying testing and commisioning telephone instrument including all cabling etc as per direction of architect and engineer in charge

MULTI PURPOSE SS 2 TIER TROLLEY /SS PLATE/ CUPS COLLECTION TROLLEY Three (2) tray type shelves of SWG 16 SS, to be reinforced with channels of SWG 16 SS. All three shelves to be equidistant. 32 mm dia SWG 16 SS pipes to extend on top as handle at 100 mm clear height from the top shelf.100 mm dia all swivel castor wheels.

Removing of existing old or broken wash basin / urinals and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

Supplying and fixing approved make FRP Liquid Soap dispensors complete with CP fixing screws and first fill of liquid soap. ( Jaguar make or Equivalent ).

Wiring for lighting/power circuit using 2.5 sqmm of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments.

Supplying and fixing superior quality 1 to 3 Module modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box.

Installation-Supply and Installation of 2-way splitters in die cast Al.casing-Installation

Supplying exhaust fan of 1440 RPM of 300mm (12") size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC Supply.

Supplying and fixing of heavy duty 25mm dia cable glands suitable for UG cable of 1.1 KV class (metal only)

POTATO / ONION / COCONUT BIN Unit of 35X35X3 mm SS angle with 18 G SS mesh constuction. SS bin cover with handle and a sliding door at the bottom front for the stored item to be taken out. Four numbers heavy duty castors of 150 mm dia with rubber wheels. Two of the wheels with locking arrangement.

Fixing all types and all capacities of fluorescent / false ceiling / spot light / CFL / LED fittings indoor on the wall / ceiling / rafters / girders using 23/0.0076” twin twisted PVC insulated wires, required Nos of round blocks and clamps.(On wall / ceiling / Rafter / Girders)

DISH WASH EXIT TABLE Constructed of 16 SWG (304) SS top, double beaded on all sides and secured to 30X30X3 mm SS angle welded framework. Top sheet to be sound deadend. Fabricated to fit the standard dish wash rack movement.Four numbers, SS tubular legs with cross supports and adjustable bullet feet. 150 mm rear splash back wherever possible.

KSRB 15-15.1 : Providing and applying painting in two coats with plastic emulsion paint of approved brand on wall surface to give an even approved shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. - with primer

Supplying Fxing approved make C.P. toilet Soap tray ( Jaguar make or Equivalent ).

Concealed Conduit System Supplying heavy gauge PVC conduit pipe 25mm dia 2mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary

Supplying and drawing PVC insulated gas injected physical foam jelly flooded co-axial TV cable.RG-6.

Supplying and drawing 2 pair PVC flexible one pair telephone unarmoured tinned copper cable.

KSRB 2-23.1 :Earth work excavation for foundation of structures by mechanical means as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising / transporting the remaining earth locally upto 1.00km lead. (Depth upto 3.00 Mts) -In all types of soil

Supplying of 1.1 KV LT 3.5 core 25 sqmm UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975

Supplying and fixing regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door /double door with powder coated painting. Made out of 14 SWG MS enclosure.II - Double Door-4Way TP &N

Supplying and fixing 40 Amps TPN miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.

Supplying and fixing of MDF krone junction box with KRONE Module / Telephone cable termination. 20 pair

Providing and fixing Chorinated Poly Venyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes jointing of pipes and fittings with one step solvent cement, trenching, refilling & testing of joints complete. (external work). - 25mm nominal OD pipes

Removing of existing old or broken Electrical fixtures like Ceiling fan etc. and disposing it with all cost and conveyance labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work.

SS POT RACK Unit to be provided with three (3) shelves, starting at 150 mm and then at equidistant, The uprights should be made of 32 mm dia SWG 16 SS pipe. The top sides of the uprights should be sealed and properly rounded. Shelves should be constructed with 25 mm dia SS pipe of 16 SWG with internal grid of 19 mm dia SS pipe at 100 mm spacing. Four numbers, 38 mm SWG 16 SS tubular legs with adjustable bullet feet.

KSRB 11-6 : Providing and fixing white vitreous china clay, water closet European type ( Pedestal type, S-trap ) with black solid plastic seat and lid, C.P brass hinges, rubber buffers. 10 litre white glazed / vitreous china clay low level, flushing cistern ( all are approved make ) with fittings, C.I / M.S brackets, 40mm diameter flush bend with fittings and clamps, overflow arrangements with specials and 25mm mosquito proof coupling of approved design, painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour complete as per specifications. Specification No. KBS 11

Providing and fixing flush door shutter made out of solid core black board type, well seasoned chemically treated hard wood battens and internal frame with minimum 45 mm wide wooden frame all-round door shutters covered with cross bonded wooden sheets (core veneer) hot pressed and fastened on both sides of the door using liquid phenol formaldehyde resin as per IS specification 2202 (Part-I) 1991. From manufacturer (Factory) complete as per specification. - 35mm thick both side commercial

Providing gutters for roof sheeting including all works etc as per architects direction and Engineer in charge

KSRB15-3.9 :Providing 18mm thick cement plaster in single coat with cement mortar 1:6, to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. I No 15.17 of SR 2018-19

KSRB 14.14-5: Providing Ceramic tiles of approved make,shade and size for flooring, treads of steps and landings laid on a bed of 12mm thick, cement mortar 1:3 mix, flush pointing with white cement using colour pigment , including cost of materials, labour, curing, complete as per specifications. - for Ceramic Tiles of size 30x30cms 6mm thick

Providing and applying water proofing in two coats of 300 microns thickness on all surfaces like concrete, Metal, Plastic , Asbestos, Wood, Cloth canopy using Heat refractive compound made out of Vinyl Acetate copolymer latex, Water, Titanium Dioxide, Barium metaborate, Ceramic Microsphere powder, Mica, Propylene Glycol in suitable proportions and the surface to be treated should be cleared of loose particles/dust/fungus etc and kept dry before the application of heat refractive compound, including cost of all materials, labour charges, HOM and machineries etc., complete.

Providing and fixing Stinless steel fixtures like Aldrops of size 300 x 16 mm, Tower bolts of size 200 x 12 mm, Latches of size 250 x12 mm, 100 mm length oxidized Iron Hinges, Handles of size 150 mm, Door Stopper & Door Bush of approved make and quality including cost and conveyance of all materials and as per the direction of EIC of work with all lead and lift and as directed by the Engineer in charge of works. Single Shutter. (Locking Arrangements)

Providing applying two coats of wall putty to inside plastered walls and ceiling using white cement putty. Scrapping and levelling the surface using steel blade and preparing the surface even and smooth by using different grade sand papers, including cost of all materials, cost of labour and scaffolding etc., complete as per the specification. Area to be considered - (a) 100% for fresh surface (b) Upto 10% for repainting

Supplying and fixing 6-32Amps SP miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.

Point wiring using Copper wire without switch.Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet.Short point up to 3Mtr from tapping point to out let via switch box

Point wiring using Copper wire without switch.Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet.Medium point above 3Mtr up to 6Mtr from tapping point to out let via switch box

Supplying and fixing of heavy duty 19/20mm dia cable glands suitable for UG cable of 1.1 KV class (metal only)

BAINE MARIE Constructed of 16 SWG SS top, double beaded on all sides and secured to welded SS angle frame, with cut out to fit in FOUR rectangular 1/1 and two 1/2 gastronom containers. Gastronom containers to be150 mm deep with lids. The tank of the baine marie should be provided with an online connection with a ball valve of 15 mm dia and a drain valve of 15 mm dia. 6 mm thick acrylic clear sneeze guard on top of the food counter at 600 mm height, resting on 25mm dia SWG 16 SS pipe upright and SS frame. SWG 18 SS sheet covering on three sides. 18 SWG ) SS bottom shelf starting at 150 mm. Thermostatically controlled 2KW heating element with rotary ON/OFF switch with light indicator on the side. Water sensor to be provided in the unit to prevent heating element getting damaged due to lack of water. The unit should have 2 mtr supply cord with industrial plug. Four numbers SS legs with adjustable bullet feet.

Dismantling the tile work in wall laid in cement or surki mortar including stacking the materials with in 50 m lead of tiles thickness 10mm to 25mm. including cost of materials, labour, HOM complete as per specifications.

Supplying ......... amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete. 100Amps 4x30x6mm Aluminium Strips

Repairs to roof with available corrugated zinc sheets/ A.C. sheets with new J bolts, screws and washers etc., on existing reeper and rafters. including cost of materials, labour, HOM complete as per specifications.

PICK UP COUNTER - UNDER COUNTER PLATE STORAGE IN FRONT / - TO BE USED FOR PICK UP) 16SWG SS top, double beaded on all sides and secured to 38X38X3 MM MS angle welded framework. Top sheet to be sound deadend. . One, 18 SWG SS bottom shelf, starting at 150 mm height and the other in the middle. All three sides covered w. Four numbers, SS tubular legs with adjustable bullet feet. Overhead shelf at 600 mm height on four SS pipes.

Idly Work Table with 1 under Shelf:Made out of St. Steel, 18 Swg with 2 round containers & 1 under shelf. The unit is Fitted with all Fitting and Accessories Manufacturing with the help of CNC laser cutting M/C , CNC bending M/C and all corner joints are TIG welded, grinded and final five stage finish and matching to the Matt sheet finish

Repairs to External elevation with available wood panels with new screws and washers etc if necessary., on existing reeper and rafters. including cost of materials, labour, HOM complete as per specifications.

Supplying and drawing UTP-CAT 6E LAN cable.

KSRB15-3.6 : Providing 15mm thick cement plaster in single coat with cement mortar 1:6, to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. I No 15.14 of SR 2018-19

SS TWO BURNER COOKING RANGE constructed of SWG 16 SS on both sides with air vents. SWG 16 SS on top with front turned down and cut out to receive Heavy grating 2no. 14"X14" heavy duty cast iron removable vessel Rest .2 G-11 burner, SWG 20 SS spillage tray with SS strip handle. Manifold - � inch dia common for burners provided on both sides16 SWG, 40x40x1.6 SS tube legs with adjustable bullet feet.

SS MOBILE SPICE TROLLEYThe unit should be like a table trolley designed with SWG 16 SS top, double beaded on all sides, secured to MS angle frame, with cut out to fit in inserts of 8 round containers to hold spices. Containers should of SS removable of size 150 mm dia and 150 mm deep with individual lids. Unit to be fitted with heavy duty noise free castors of 100 mm dia with two castors having locking facility. The trolley should have 25 mm dia SWG 16 SSS pipe handles on both sides. One undershelf of SWG 18 SSS at the bottom at 150 mm from FFL..

Fabricating, supplying and erecting M.S. TubularTruss of span upto 10m. The bottom and top member is provided with 50x50x6mm double equal angles, welded back to back and in between top and bottom line, in areas of mid section is provided with 50x50x6mm equal single angle for vertical and inclined members and at supporting ends 40x40x5mm single angle is provided. All the members are welded together with 6mm gusset plate as per Drawing. The entire truss is anchored in RCC column by using 4 Nos. of M.S. anchor bolts at each support, with 10mm thick base plate and shoe plate.The work includes cutting, straightening, placing in position of M.S angle and wleding wherever necessary, and applying one coat of red oxide primer coat to all themembers including cost of all materials, labour charges, and hire charges of machineries for cutting, welding, grinding and erection equipments, with all lead and lift, transportation, etc., complete as per specification.

Supply and fixing shingles on existing Corrugated sheet fixing with 60 mm length self tapping screws of 10g, metal and bitumen washers including cost of materials, labor, complete as per specifications

Waterproofing of RCC Terrace / podium slab / toilet / utilities / water retaining structure by preparing the surface by chipping and cleaning and Grouting of Honey comb, voids,cracks / construction joints with cement slurry (1kg cement added in 10 ltr of water) added with 100gm of inorganic accelerator, followed by spraying of liquid biological modified alkaline earth silicates @ 0.40 ltr per sqm on whole surface to reduce the micro porosity and allowing it to dry, curing the surface for the silicates to penetrate deeper into the concrete and spraying waterproofing impregnate liquid containing silane and silanol linear copolymer @ 0.50 ltr per sqm and finally applying polymer slurry made out of cross linked acrylic / styrene / butadiene & cement in the ratio of 1:0.1, @0.50kg/sqm on the whole surface, including all labour charges tools and equipments, all complete as per the specification

37.33 Providing and fixing hydraulic door closures-Aluminium body.

Dismantling the tile work in floor and roof laid in cement or surki mortar including stacking the materials with in 50 m lead of tiles thickness 10mm to 25mm. including cost of materials, labour, HOM complete as per specifications.

Supplying and fixing superior quality 6 Module modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box.

SS HOOD WITH FILTTER Supplying, installation, testing of Exhaust Hood with oil grease filters, made of Stainless Steel Sheet Hood with SWG Thick SS Sheet grease filters hood Size . Including welding, grinding buffing, polishing and making curvature (when ever required) etc complete,

SS CLEAN DISH RACK Unit to be provided with four (4) shelves, starting at 150 mm and then at equidistant, constructed with 38 mm dia SS pipe of 16 SWG 150mm Sheet frame under support. 18 SWG SS shelf double beaded on all sides. Four numbers SS legs with adjustable bullet feet.

Supplying, installation, testing and commissioning of 8 channel Wireless DVR as per direction of Architect and Engineer in charge .The prices should include the necessary mounts and brackets.

Supplying of recess mounting non integrated type LED down light ...... W luminaire comprising of pressure decast/ extruded aluminium housing, with spring loaded false ceiling clamps, LED of Power/COB with CCT 6500 degree K, CRI> 70%. efficacy >100 lumen per watt, 120degree beam spread, life> 25000 burning hours and Compliance to IS 10322/IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level. LEDs are driven by HF electronic driver integrated in a separate control gear assembly., with PF > 0.95, power loss should < 5% of lamp wattage., short- 15-18W

Supplying and fixing of 6Amps one way modular switch/ Socket/stepped electronic fan regulator/ dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293

Providing & Fixing of corner beads of wooden door frame to wall including cost of materials, labour charges, complete as per specifications.

KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of Design mix M20 with OPC cement @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to is 9103-1999 reafirmed-2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnspillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM of machinery, curing, complete but excluding cost of reinforcement as per specifications. Specification No. KBS 4.1, 4.6(Deck slab)

Supplying and fixing superior quality 4 Module modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box.

4 DOOR VERTICAL REFRIGERATOR Unit shall be of full SS construction with interior and the exterior of 20 G SS 304. The inner wall will be suitably insulated with PUF 50mm thick. It should have 4 doors, constructed of 18 G SS and inner 20G SS. The doors should be provided with magnetic locking device and the unit will have adjustable perforated ( CTC 50mm ) intermediate shelves of 18 GA inside. It should be fitted with digital temperature indicator, control switches and indicator lights.The equipment should be able to maintain a t Temperature of +0˚C to +6˚C. . The unit shall be provided with a removable SS drip tray below. The compressor unit will be top mounted and should be of a reputed make from Emerson Copeland Four [4] Nos. 16 GA S.S 50 mm Ø tubular legs with. adj.nylon bullet feet. 150 mm clearance to be given from the floor. ELECTRICAL 1KW/16A/1∅ SUPPLY Ht @ 2100mm AFFL