Directorate Of Municipal Administration Tender

code04 - Supply and delivery at site special moulded variety HDPE tee as per IS 170mm dia pipes. 100 ID TEE fitting for 100mm dia pipes

code05 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron DI conforming ti IS 1865 with the latest amendments and of grade GGG 40 50 shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100 leak proof with face to face dimensions as per IS 14846 2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings minimum 2 O rings Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves T.P set galvanized bolts nuts and rubber insertions etc. but excluding earth work. For PN10 Note TP set should be considered only for DI pipes estimate. For MS pipes estimates TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate etc. complete For sluice For sluice Valve of PN 10.0 and 100mm

code06 - Refilling available earth around trenches pipelines cables in layers not exceeding 20 cms in depth compacting each deposited layer by ramming after watering with a lead upto 50 m and lift upto 1.5 m. Including cost of all labourcomplete as per specifications

code07 - Providing laying and jointing HDPE pipes of specified grade and conforming to IS 4984 2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches laying true to line and jointing of pipes and specials with electrofusion welding giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee stub ends flanged sets bedns reducers etc. complete Contractor will make his own arrangements for procuring water for testing etc complete NOTE HDPE Grade PE80 PN10. 75mm dia

code08 - Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches laying true to line and level and perfect linking at joints with the help of two O rings and a coupler of suitable size including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour all lead and lift including encasing the Specials around to a depth of not less than 15 cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing 100 ID COUPLER fitting for 75mm dia pipes

code09 - Supply and delivery at site special moulded variety HDPE tee as per IS 75mm dia pipes. 75 ID TEE fitting for 75mm dia pipes

code10 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron DI conforming ti IS 1865 with the latest amendments and of grade GGG 40 50 shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100 leak proof with face to face dimensions as per IS 14846 2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings minimum 2 O rings Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves T.P set galvanized bolts nuts and rubber insertions etc. but excluding earth work. For PN10 Note TP set should be considered only for DI pipes estimate. For MS pipes estimates TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate etc. complete For sluice For sluice Valve of PN 10.0 and 75mm

code11 - Geophysical investigation at site for sinking borewells for Providing drinking water to the habitation either through the Hand Pump MWS or P W S S by vertical electrical sounding by adopting Venner or Schlumbergers s method including reconnaissance survey of geological formation. Geophysical investigation of existing ground water in the vicinity its quality quantity and acceptability of the users indicating the location of the site recommended depth of casing pipe required to seal the top unconsolidated formation including an extra depth of 1.0 metre in consolidated formation for proper seating of casing pipe depth of drilling required to cover full depth of aquifer proposed to be tapped probable yield and other information required including transportation of instruments and accessories to work site engaging technical personaland labour required etc. NOTE 1 Additional rate on item 1 2 is allowed for drilling in over burden and fixing Casing pipes beyond 20M for fixing Casing pipes only a Above 20 M and upto 30 M 15 b Above 30 M 30 Measurement of overburden is restricted to the depth of casing pipe fixed excluding initial depth of 20M and projection above ground level. 2 A sum of Rs. 100 is to be deducted for Dry Borewell towards yield test

code12 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG above 1100 CMF above in all strata including over burdern upto 20 m. Fixing of casing pipes collars and cap with necessary cutting threading and welding including transportation of rig and supporting vehicle crew charges and cost of consumables etc complete including yield testing at the final depth with a minimum working of compressor for one hour Excluding cost of casing pipes collars cap etc complete Above 450m of drilling add 10 for every 50m depth Borewell depth of 0 to 50 Mtrs

code13 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG and above 1100 CMF above in all strata including over burdern upto 20 m Fixing of casing pipes collars and cap with necessary cutting threading and welding including transportation of rig and supporting vehicle crew charges and cost of consumables etc complete including yield testing at the final depth with a minimum working of compressor for one hour Excluding cost of casing pipes collars cap etc complete Above 450m of drilling add 10 for every 50m depth Borewell depth of 50 to 100 Mtrs

code14 - Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG above 1100 CMF and above in all strata including over burdern upto 20 m Fixing of casing pipes collars and cap with necessary cutting threading and welding including transportation of rig and supporting vehicle crew charges and cost of consumables etc complete including yield testing at the final depth with a minimum working of compressor for one hour Excluding cost of casing pipes collars cap etc complete Above 450m of drilling add 10 for every 50m depth Borewell depth of 100 to 150 Mtrs

code15 - Providing PVC ringtite pipes conforming to IS 4985 2000 with latest amendments and conveying to worksite rolling and lowering into trenches laying true to line and level and perfect linking at joints testing and commissioning including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials excluding cost of specials with jointing of approved type with all labour with all lead and lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS Contractor will make his own arrangements for procuring water for testing etc. com PVC pipes 160mm DIA 6KG sq cm Class 3

code16 - Pumping Machinary Providing Single Phase Submersible Pump Sets of 100mm dia 4 inch suitable for bore well confirming to IS 8034 2000 specifications to work site with testing of as per instructions of engineer incharge of work and latest amendments 26 STG

code17 - Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core sheathed of nominal cross sectional area as per IS 694 1990 with ISI Mark and as per its latest amendments

code18 - Supply installing testing and commissioning COMMON control panel consisting of the following INCOMING 1 No set of Phase indicating lamps with SFU of suitable rating 1 No Analog Ammeter 1 No Analog Voltmeter 1ni with Phase selector switch Isolating switch OUTGOING for Main Electrical Pump 1 No MCB 1 No DOL of S D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor under voltage over Volage under current over current dry run protection suitable for the pump described above 1 no Indoor type NOTE 1 DOL Direct Online Starter Upto 3 HP pumps 2 S D Star Delta Starter etc complete

code19 - Labour charges for providing connection using insulated sheathed steel wire cable as per IS 1554 1988 with latest amendments from KPTCL pole to meter board unit with all necessary materials tools and equipments as per specificationswith testing of as per instructions of engineer incharge of work.

code20 - Supply and delivery at site brand new best make pressure guage suitable for centrifugal pump confirming to latest IS standards. pressure guage 80MM

code21 - Supply and delivery at site best indigenous brand new power capacitor as per IS 2834 1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning of the same at the location of respective pump sets.

code22 - Supply and delivery at site 50mm 2 dia heavy duty unplasticized PVC Column pipes with heavy duty collars,rubber profile ring vibration control profile ring freezing and turbulence free leak proof EPDM ring with ISI mark with its latest amendments

code23 - Supply and delivery at site of brand new best make non return valve as per IS 778 1984 with ISI Mark and as per its latest amendments Size 50 mm

code24 - Labour charges for Erection Electrification and commissioning of Pump sets including aligning and balancing of all items including supply and erection of two pair of supporting clamps bore well caps cable clips and water tight gland cable protectors bolts nuts valve and gauges tools and equipments etc involved in the job as per specifications with necessary tests as per specifications with testing of as per instructions of engineer incharge of work.

code25 - Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour tools and equipments including providing cement concrete foundation bed etc. complete as per specification with testing of as per instructions of engineer incharge of work.

code26 - RCC hume pipe Circular pump house Providing precast RCC Circular Hume pipe pump house with M.S door and RCC conical roof as per specification and drawings Internal dia Mtr 1200 mm height of 2.5Mtr With Wall thickness 65mm etc complete

code27 - Erection and positioning of RCC Hume pipe pump house Cistern on size stone masory platform including transportation charges and handling finishing with all necessary tools plants and materials etc complete as directed by the Engineer in charge of work

code28 - Earth work excavation by manual means for drains canals, waste weir, draft, approach channels, key trenches, foundation of Buildings bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools other appurtenaces required to complete the work.

code29 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite trap basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1 3 6 Using 40 mm nominal size graded crushed coarse aggregates

code30 - Providing Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1 6 12 1 cement 6 coarse sand 12 graded stone aggregate 20 mm nominal size upto plinth level with :Cement mortar 1 6 1 cement 6 coarse sand

code31 - Providing Size Stone masonry with hard stone in foundation plinth with Cement mortar 1 6 1 cement 6 coarse sand

code32 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite trap basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness well compacted using plate vibrators, including all lead & lifts cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1 2 4 Using 20 mm nominal size graded crushed coarse aggregates

code33 - Providing 20 mm cement plaster of mix 1 6 1 cement 6 fine sand to brickstone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

code34 - Providing, Laying and Fixing of GI pipes conforming to IS 1239 1990 with latest amendments complete with GI fittings excluding the cost of fittings with cuts and threads wherever necessary including testing for water tightness, with all lead and commissioning. contractor will make his own arrangements for procuring water for testing For Heavy Duty GI Pipe etc complete Heavy Duty GI pipe of 32mm dia