Directorate Of Municipal Administration Tender

Supplying of……… mm dia class A GI pipe bracket up to 2 mtrs long bent at suitable angle and fixing to this bracket 1x40/2x40 or rail or RCC pole/wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires complete – 32mm dia [P-108/17.1.2]

Supplying, fixing wiring earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90 thick GI 2.5 mtr. long buried in a pit… the pit should be filled with equal proportion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia.[P-55/7.1]

"Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level consolidating etc., complete. (As per Civil SR KSRB I-2, P-7) In soil (Ordinary) (Pg No. 61 I No. 7.9.1)"

Supply and laying double walled corrugated (DWC) HDPE Pipe including all necessary connecting Sockets/Couplings/Tees/Bends/End-caps of same materials in existing trench as per IS 14930 part - II suitable for drawing underground cables. 63mm OD / 50mm ID (SR Pg No. 63 I No. 7.20.3)

Labour charges for laying of 1.1KV class UG cable in existing trench GI pipe / stoneware pipe / on wall/ on pole as required. In existing trench/duct . 25 sqmm to 75 sqmm (Pg No. 61 I No. 7.8.2)

"Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV...40mm (SR Pg. No. 62 I No. 7.12.1)"

"Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm (P No. 67, I No. 12.9.6) DMA APPROVED RATE"

Supplying and fixing L.T. Cast Iron Pot heads suitable for 1.1KV class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps, bolts, nuts and washers etc. 25 Sqmm(P no. 62 I No. 7.13.3)

"Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. GI strip 25x6mm (P No. 55 I No. 7.3.2)"

"KSRB 4-1.3 : Providing and laying in postion plain cement concrete of mix 1:4:8 with OPC cement @ 180kgs, with 40mm and down size graded granite metal coarse aggregrates @0.85cum and fine aggregates @ 0.57cum machine mixed, machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation, including cost of all materials, labour, HOM of machinery, curing complete as per specifications. Specification No. KBS 4.1, 4.2 (PW,P & IWTD SR pg No. 12 I No. 4.3)"

Supplying of street light integral induction luminary fittings single piece die cast alluminium housing with full toughened glass, prewired electronic control gear to operate on 230V 50Hz AC supply and suitable wattage induction lamp. The body of the fitting shall be finished with black/grey powder coated paint with enclosure conforming to IP65 specifications – 70 watts (Page no:24 Item no:4.27.1 )

"Laying of UG cables by trenchless technology by Adopting hortizontal boring & Drawing of cable including preparation of site With HDPE pipeRock soil 5"" bore size (Bescom Common SR 2014-15 P No. 161 I No. 27.2.1)"

"Supplying, fixing and wiring elctronic 5 to 63 Amps single phase class-1 Accuracy with Tamper proof Energy meter (SR Pg No. 48 Ino. 6.28)"

Supplying and Fixing of........mm dia class A GI pipe bracket up to 2 Mtrs long bent at suitable angle and fixing to this bracket 1x40/2x40 watts fluorescent tube street light fitting of all capacities to GI or CI or rail or RCC pole / wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires. 32mm dia GI Pipe

KSRB 15-18.2 : Providing and applying enamel metal paint two coats (excluding priming coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other foreign matter, including cost of materials, labour, complete as per specifications.

"Fixing halogen/metal halide/SVL/IL/LED floodlight fitting over existing pole / wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires. (P No. 108 I No. 17.5)"

"Multy strand multi core PVC insulated unarmoured copper cable 2.5sqmm 3 core (P No. Ix I No. 73)"

"Supplying .. Amps rated 3phase with neutral busbar using required capacity Electrolytic aluminium strips covered with heat Shrinkable coloured PVC sleeve mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S. flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc. complete. 100Amps 4x30x6mm Aluminium strip (P No. 49 I No. 6.38.1)"

"Supplying of 1.1KV LT UG cable having aluminum conductor PVC insulated, extruded inner sheathed, galvanised, steel strip (except 2CX10sqmm wire armoured) confirming to IS-3975:1990 (No. of strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS-1554 Part 1:1988 & confirming to GTP of Group-A. 3.5 core 25 sqmm (Pg No. 55 I No. 7.4.6)"

"Supplying & fixing of Porcelain fuse channel with cutout on existing wooden/panel using necessary nuts, bolts and washers. 63 Amps (P No. 44 I No. 6.7.3)"

"Fabrication, Supplying, Erection, testing and Commissioning of 12Mtrs/12.5Mtrs Long polygon high mast with single/ mutiple telescopic sections having, (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grade S 355 JO /ASTM A572-50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/sec as per IS 875 part 3 (as per GA drawing). Base plate as per IS 2062/ASTM A572-50. The mast shall be Galvanised in single Hot-dip as per BSEN ISO 1461/ASTM A123 with an average 70microns as per IS 2620, and welded as per BS 5135 Single L - Seam joint. The mast shall have 2way head frame with die cast LM-6 pulleys, stainless stel axle, Phosphorus Bronze bearing bush press-filled with seperate guides for 2 runs of 5mm dia, stainless steel wire rope of AISI 304grade 7/19-core, (Factor of safety as per TR no-7). 205sqmm EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement. the mast shall have power tool operating on 230/415V, 50Hz, 1/3 phases reversible geared motor. the mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be supplied with 3mm thick template, lighting arrester of 1.2m length galvanised pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin lamps fitting with wiring complete. (excluding foundation) as per technical data. (12Mtrs/12.5Mtrs - Top 100mm and bottom 310mm dia) (SR Pg. No. 15 Ino. 3.5.2)"

Supply and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, wahers and wiring etc., complete with AC-3 Rating and as per IS-13947 – 60-70 amps [P-46/6.12.4]

"KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of design mix M20 with OPC cement @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.69cum and fine aggregates @ 0.460 cum, with suoer plasticisers @ 3 liters confirming to IS 9103-1999 reafirmed-2008, machine mixed, concrete laid in layers not exceeding 15 cmc thick, vibrated for al works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnpillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM of machinery, curing, complete but excluding cost of reinforcement as per specifications. Specification No. KBS 4.1, 4.6 (PW,P & IWTD SR pg No. 13 I No. 4.11)"

Supplying and fixing circuit breakers on existing MCB distribution boards using necessary fixing materials and ‘C’ type curve, indicator ON/OFF, energy cross-3 with short circuit breaking capacity of 10K and Complete wiring as required - 50-63 amps TPN [P-47/6.16.4]

"KSRB 2-2.1 : Earthwork excavation by manual means for foundation of buildings, culverts, water supply and sanitary lines and electrical conduits etc, either in pits or in trenches 1.5 m. And above in width, in ordinary soil not exceeding 1.5m in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soilclear from edges of excavation with lead upto 50m. including breaking of clods complete as per specification. No. KBS 2.1(a)/2.3.5 (PW,P & IWTD SR pg No. 5 I No. 2.3)"

KSRB 15-18.1 : Applying red lead ready mix priming coat over new steel or other metal surface including preparing the surface after throughly cleaning oil, grease, dirt and other foreign matter, and scoured with wire rushes, fine steel wool, sand papers including cost of materials, labour, complete as per specifications.(SR Pg 124 It 15.73

"KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of design mix M20 with OPC cement @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.69cum and fine aggregates @ 0.460 cum, with suoer plasticisers @ 3 liters confirming to IS 9103-1999 reafirmed-2008, machine mixed, concrete laid in layers not exceeding 15 cmc thick, vibrated for al works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnpillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM of machinery, curing, complete but excluding cost of reinforcement as per specifications. Specification No. KBS 4.1, 4.6 (PW,P & IWTD SR pg No. 13 I No. 4.11)"

Supplying and fixing Microprocessor based Astronomical timer switch with using necessary bolts, nuts and washers etc., [P-51/6.46]

Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved paint. (Pno.30 It 5.41.2) 50X50X6

Supplying of street light integral induction luminary fittings single piece die cast alluminium housing with full toughened glass, prewired electronic control gear to operate on 230V 50Hz AC supply and suitable wattage induction lamp. The body of the fitting shall be finished with black/grey powder coated paint with enclosure conforming to IP65 specifications – 70 watts (Page no:24 Item no:4.27.1 )