Directorate Of Municipal Administration Tender

1.8 - Construction of Embankment by excavating the available approved Gravel/ Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work.

4.17 - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

2.1.3 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.- Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates

6.8.2 - Providing and laying 80mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Commercial Traffic Axle load repetitions upto 10MSA & for Residential Streets of approved shape and colour, laid in required pattern and including over 40mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (WMM/WBM Base to be paid separately as per relevant technical specification)

8.1b - Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 15 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409- PCC M20 grade for kerb Cast in Situ

2.2.1 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. - M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. Including Shuttering for Footing (8%) as per App-I

2.2.1 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. - M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. Including Shuttering for Columns (70%) as per App-I

2.2.1 - Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. - M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

2.11a - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. 2.11a for Building works

2.11h - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. for other works

6.32 - Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications.

5.1.1 - Providing Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stoneaggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand)

2.1.5 - Providing and laying in position Cement Concrete for levelling course for all works infoundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregatesas per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. - in 1:2:4

8.5.2 - Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

8.28 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

sl no 64 - Sand - M-Sand for Childrens Play Area

020 - PUPPY DOG RIDER Supply and Fixing of Puppy Dog / Elephant / Horse / Bike / Rider: Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish. The rider is of size 0.9 m x 0.4 m x 0.55 m, Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety feature. All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 0.9 m x 0.40 m x 0.76 m

021 - TWO SEATER SEE SAW Supply & Fixing of Two Seater See Saw : All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 2 seats which is made of LLDPE virgin plastic of size 364 mm X 250 mm X 180 mm. Each seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of Dia 32 mm. Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 1.91 m x 0.5 m x 0.82 m

022 - 150 CM SLID Supply & Fixing of 150 CM Slide: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. “A” shaped support posts of height 2.28 m, are to be schedule Galvanized steel with a 60mm OD Outer Diameter. Deck of size 0.80 m x 0.60 m and Staircase of size 1.84 m x 0.60 m shall be an all-ROBOTIC welded assembly fabricated from perforated solid punched steel. Deck perimeter is precision pre punched for attachments. Decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. Handrail of height 1.9 m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes. Wavey Slide of size 2.95 m x 0.72 m x 1.72 m. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 4.18 m x 0.89 m x 2.28 m

023 - MERRY GO ROUND DX Supply and Fixing of Merry Go Round DX: The Merry go round consists of a round platform which is made of galvanized steel and has a thickness of 2.5 mm. It is also power coated with the thickness of 2.5 mm. It is of Dia 1210 mm. It has 3 inverted “L” shaped handrails which is made of Galvanized steel and of dimensions as 474 mmx 815 mm. It has thickness of Dia 32 mm. The 3 handrails are separated exactly. All the 3 handrails are connected to the Centre with the help of a rod which is also made of Galvanized steel and of Dia 48 mm and height 815 mm. All joints are Robotic welded. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: Dia 1.21 m

024 - A - SWING Supply & Fixing of A Swing: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. “A” Shaped support posts of height 2.1 m are to be schedule Galvanized steel with a 80mm OD Outer Diameter. Toprail of length 2.58 m and Dia 76 mm shall be an all-robotic welded unit, fabricated from O.D. galvanized steel pipes. Flat Swing seat of size 440 mm x 150 mm x 30 mm, Bucket Swing seat of size Dia 325 mm and height 245 mm. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 2.5 m x 1.5 m x 2.1 m

025 - CROSS WALKER /DOUBLE AIR SKIER Supply and Fixing of Double Air Skier: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. " All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The suppliers products must have been installed in at least 100 public parks across India the list of which to be submitted during the technical bid. Any five parks will be randomly selected by the tendering authority or a third party appointed by it to check and ascertain the product GS Marks, safety, quality and durability at site, the evaluation report to have photographs of the installed products taken at site showing the GS mark and the condition of the equipment, based upon which the tender shall be evaluated. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. The Foot rest of size 365 mm x 164 mm is fixed to the Standing Bars of length 1640 mm x 40 mm shall be an all-robotic welded unit, fabricated from 40 O.D. galvanized steel pipes. Lower part of Support Handrails of size 0.8 m high and Dia 47 mm and Upper part of Support Handrails of size 0.51 m high and Dia 32 mm are all robotic welded fabricated from 47 mm O.D. and 32 mm O.D. galvanized steel pipes. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered safety caps as per EN16630 standards. Joints are robotic welded. EQUIPMENT DIMENSIONS: 1.61 m x 0.52 m x 1.51 m

026 - SEATED CHEST PRESS / SEATED CHEST PRESS Supply and Fixing of Seated Chest Press: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. " All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The suppliers products must have been installed in at least 100 public parks across India the list of which to be submitted during the technical bid. Any five parks will be randomly selected by the tendering authority or a third party appointed by it to check and ascertain the product GS Marks, safety, quality and durability at site, the evaluation report to have photographs of the installed products taken at site showing the GS mark and the condition of the equipment, based upon which the tender shall be evaluated. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.88 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two pair of U-Shaped Bars of 1.02 m and Dia 40 mm while the handles are placed at a spacing of 698 mm shall be an all-robotic welded unit, fabricated from 40 O.D. galvanized steel pipes. Joints are robotic welded. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with caps as per EN16630 standards. Joints are robotic welded. EQUIPMENT DIMENSIONS: 1.82 m x 0.69 m x 1.88 m

027 - LEG PRESS / SQUAT PUSHER Supply and Fixing of Squat Pusher: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. " All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The suppliers products must have been installed in at least 100 public parks across India the list of which to be submitted during the technical bid. Any five parks will be randomly selected by the tendering authority or a third party appointed by it to check and ascertain the product GS Marks, safety, quality and durability at site, the evaluation report to have photographs of the installed products taken at site showing the GS mark and the condition of the equipment, based upon which the tender shall be evaluated. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Vertical bars height of 1.50 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. L shaped bars of 960 mm x 600 mm carrying two seats of 0.34 m x 0.34 m shall be an all-robotic welded unit, fabricated from 40 O.D. galvanized steel pipes. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN16630 standards. Joints are robotic welded.EQUIPMENT DIMENSIONS: 1.93 m x 0.56 m x 1.70 m

028 - LEG&THIGH EXERCISE /AIR WALKER SINGLE HEALTH WALKER Supply and Fixing of Health Walker: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. " All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The suppliers products must have been installed in at least 100 public parks across India the list of which to be submitted during the technical bid. Any five parks will be randomly selected by the tendering authority or a third party appointed by it to check and ascertain the product GS Marks, safety, quality and durability at site, the evaluation report to have photographs of the installed products taken at site showing the GS mark and the condition of the equipment, based upon which the tender shall be evaluated. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot Rest of size 361 mm x 161 mm are attached to the Standing Bars 957mm x 60 mm shall be an all-robotic welded unit, fabricated from 60 O.D. galvanized steel pipes. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN16630 standards. Joints are robotic welded.EQUIPMENT DIMENSIONS: 1.18 m x 0.553 m x 1.25 m

029 - WAIST TWISTER TRIPLE / WAIST TWISTER Supply and Fixing of Waist Twister: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. " All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The suppliers products must have been installed in at least 100 public parks across India the list of which to be submitted during the technical bid. Any five parks will be randomly selected by the tendering authority or a third party appointed by it to check and ascertain the product GS Marks, safety, quality and durability at site, the evaluation report to have photographs of the installed products taken at site showing the GS mark and the condition of the equipment, based upon which the tender shall be evaluated. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.35 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. The poles are welded on to a base plate made from steel with 114mm inner diameter. Circular Handrail Dia 42 mm. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN16630 standards. All joints are robotic welded.EQUIPMENT DIMENSIONS: 1.44 m x 1.29 m x 1.35 m

030 - General Cleaning : clearing of land by cutting of thick and sparse growth plants(0.25 mt thickness plants and clearing of bushes along with roots( throwing away to 1.5mtr height and 50 mtr far) FOREST/ HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.1 Page No. 48.

031 - Red Earth: Procurment of Fine coarse Red-earth/soil, FOREST / HORTICULTURE /WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 1.2(a) Page No. 1.

032 - Lawn : Maxican Grass Dibbling cost, FOREST/HORTICULTURE/WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: I(c) Dibbling Page No.50

033 - Growing of Hedges: Digging trench of size 1mx0.30mx0.45m and filling 50% of the trench with top soil and remaining 50% trench with1:2:3 proportion of sand (0.0112), FYM (0.0224cum) red earth (0.0336cum) and planting of well grown plants (excluding cost of plants) FOREST/ HORTICULTURE /WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.9(a) Page No.49.

034 - Cost of Hedges Plants : 1) Durantha Plant, 2) Irantimum Plant, 3) Akelifa timma plant,4) Akelifa Godreg, Etc.,

035 - Planting of Trees: Digging pits of size 0.75 x 0.75x 0.75m, filling 50% of the pit with top soil and remaining 50% of pit with 1:2:3 proportion of sand (0.035cum) FYM (0.070cum) Red earth (0.105 cum) and planting of well grown tree saplings (excluding cost of plants) FOREST/ HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.2(a) Page No. 48.

036 - Cost of Tree Plants: Areca Palm, 2) Royal Palm, 3) Faicus Beneginam, 4) Faicus Starlight Etc.,

037 - Planting of Shrubs : Digging pits of size 0.45 x 0.45 x0.45m filling 50% of the pit with top soil and remaining 50% of pit with1:2:3 proportion of sand (0.007), FYM (0.014cm) red earth (0.021cm) and and planting of well grown tree saplings (excluding cost of plants) FOREST/ HORTICULTURE/ WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.3(a) Page No. 48.

038 - Cost of Shrub Plants: 1) Ixora plants ,2) Hybiscuous plants 3) Iporbiya plants, 4) Jathropa plants, 5)Sang of India plants, 6)Dust miller plants, Etc.,

039 - Planting of Creepers:Digging pits of size 0.45 x 0.45 x0.45m filling 50% of the pit with top soil and remaining 50% of pit with1:2:3 proportion of sand (0.007), FYM (0.014cm) red earth (0.021cm) and and planting of well grown tree saplings (excluding cost of plants) FOREST/HORTICULTURE/WATERSHED DEPARTMENT Common Sanctioned SR 2022-23 I.No: 12.4(a) Page No. 48.

040 - Cost of Creepers: 1) Almond, 2) Bignonia-gracillis, 3) Bignonia- Venusta, etc.,

041 - Bulbous Beds: Developing bulbous beds by digging to a depth of 0.45M filling 50% of the area with excavated top soil and remaining g50% with sand (0.0375 cum) FYM (0.075 cum) red earth (0.112 cum) (i.e.in the proportion of 1:2:3) and planting with bulbous bed P.No.63, Sl.No10 a

042 - Cost of Bulbous Plants: 1) Canna, 2) Tuberose, 3) Gladiullas, 4) Lilly, etc.,

043 - Garden Maintenance. SR 2020-21 P.No .64, Sl No.12.11(a) Upto 8000.0 m2

044 - Providing and fixing seating bench 1 no base slab, 1no back rest, 2no legs, made up of granite stone with nice finish chamfered edge and fillet corner finishes is conveyed to work site it is inclusive of all lead and lift, labour, transportation loading unloading charges, over heads, hire charges of machinery all and placing in position etc., complete work shall be carried out as per the detailed specification. Architect drawing and direction of the engineer in charge of the work. the work includes all other incidental work required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work required in fixing the equipment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of engineer in charge.

045 - Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications

046 - Providing and applying two coats of ready mix paint of approved brand on steel surface after thorough cleaning of surface to give an even shade