Directorate Of Municipal Administration Tender

code19 - Supplying and drawing PVC insulated flexible copper wire of approved make. 40/0.0052" (P-5, It-2.4.7 of PWD SR Part I)

code01 - Fabricating, supplying and erection of ... ms long hot dip Galvanized Octagonal hot dip Pole with BSEN 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/s for .......m Pole in single section and single joint welded as per IS 9595/IS10178AWS having dimensions bottom ..... mm , top.... mm with 3 mm thick,suitable base plate and 4Nos of ..... long J bolts along with template and the Pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM-A123 and 153 etc., (excluding foundation) as per drawing appended. 9 m - Top 70 mm and Bottom 155 mm dia. (P-10, It-4.2.7)

code06 - Supplying 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975. 25 Sqmm, 4 Core, (13 GI Strips - 4 x 0.8 mm) (Sl.no 204,It-32.08 of Eescom SR Part III )

code07 - Earth work excavation for cable trench of 0.5 to 0.75 Mtr. Width and Depth upto 1 Mtr including trial pits, depositing on bank upto a lead of 50 Mtr, Supplying and Displaying necessary Danger Boards and Lighting, Using sight Rails and Sign Boards at every 100 Mtr wherever necessary as directed.In Hard Soil. (P-9,It-31.05 of Bescom SR Part IV )

code13 - Supplying and fixing Microprocessor Based Astronomical timer Switch with using necessary bolts, nuts and washers.(P-20, It-5.48 of PWD SR Part I)

code14 - Supply and fixing of 3pole power contactor with NO/NC contacts on existing wood/panel board using necessarybolts, nuts, washers and wiring etc., complete with AC-3Rating and as per IS-13947. 60 to 70Amps (P-15, It-5.13.3 of PWD SR Part I)

code09 - supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 20A single phase Class-1 Accuracy with Temper Proof Energy Meter. (P-17, It-5.3 of PWD SR Part I)

code12 - Supplying 100 A 4 x 30 x 6 mm Aluminium Strips amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete.(P 19, It-5.40.1 of PWD SR Part I)

code18 - B) 4 Sqmm

code05 - Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS 8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100V as per IS 694:2010. 4C X 2.5Sq.mm. (P-4, It-2.78 of PWD Ele SR Part-1)

code17 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments(P-4, It-2.3 of PWD SR Part I) A) 2.5 Sqmm

code22 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates I.No.2.1.4P.No.15, Vol-I

code20 - Earthing: Supplying and fixing and wiring earth electrode for grounding circuits IC cutouts and other equipments on the meter board in the pit. The pits should be filled up with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduits etc. is to established through GI wire of sizes as per clause 7.3.3 of IS 732 using 12mm bolts, nuts, washers and check nuts, the pipe shall have 16 through holes of 12mm dia.(Page 157, Item No. 13.39 Vol-V of 2023-24 SR)

code11 - Supplying and fixing angle iron frame work fabricated out of M.S angle iron… and M.S. flat… with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. Size: 40 x 40 x 6 mm. (P-19, It-5.41.1 of PWD SR Part I)

code02 - Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation.Lamp compartment comprising of anti glare clear diffuserwith Injection moulded polycarbonate/clear glass material,delivering superior light output Rated life Burning Hrs 50000hr @ Lumen Maintenance of 70 percent CCT 5500K, IP 66optical and electrical compartment & impact resistance ofcomplete uminaire IK08. Power Factor 0.9 with mains,Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatiblefor pole mauling with outer dia of 40mm to 50mm. UniversalVoltage driver to operate wide voltage range from 100 V to 270V50/60Hz application. Compliance to IS 10322/ IEC 60598,LM 79 & LM 80 Adherence with RoHS. UL pprovedMCPCB. Top access street light with single screw to ensureease of maintenance at the sight site location withminimized minimal tools. LED Light fixture with 120 W System Power consumption. LED Efficiency 1301m/w, nominal CRI 75. Luminaire manufacturer should have in- house facilityaccredited by NABL / CPRI & any Government certifiedagency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark / name shall beEngraved / Embossing on the die cast housing / Body partWarranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentionence. LED Floodlight 120W.(P-45, It-11.9.3 of PWD Ele SR Part-1)

code16 - Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220 volts AC 50 Hz 12/24V DC. (P-18, It-5.38 of PWD SR Part I)

code21 - Earth work excavation for FOUNDATION by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including cost of explosives, dressing of excavated surfaces, disposing off or levelling the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost oflabour, blasting materials, tools, usage of Machinery & all other appurtenaces required to complete the work In Hard Rock (requiring blasting) Depth upto 1.50m. (P- 9, It - 1.16.1 VOL-I)

code03 - Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete. Double Arm Bracket with 1000 mm Standard 40/50 mm dia. (P-12, It-4.6.4)

code08 - Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/ Aluminum Rollers as directed by the departmental staff. LT Cable-2.5 to 25 Sqmm. (Sl no-175,It-21.06 of Eescom SR Part IV )

code15 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.50-63Amps TPN (P-16, It-5.18.9 of PWD SR Part I)