Defence Research And Development Organisation Tender

Providing, fabricating & Installation of Full height Aluminum Partition including 02 Nos of doors. All the Vertical & Horizontal members shall be powder coated AL Sections of size 65 x 40 x 1.2 mm heavy gauge forming a grid as per drawing enclosed. The partition shall be rigidly fixed to wall / Ceiling / floor, etc for stability, the filler material shall be 05 mm thick clear glass or pin head glass fixed using AL snap fit clips, rubber gaskets,. etc complete as per samples available at ADA.

Glass reinforced Gypsum (GRG) plaster board 12.5 mm thick confirming to IS 2095 (Part 3):1996

Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non-combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and L- sections suitably fixed according to tile size as per direction of Engineer-in-charge.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and color of two coats.

Finishing walls with water proofing cement paint of required shade of Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Specialized technicians and Helper (Technician) for removing the existing broken glasses and shifting the glasses to the location as decided by ADA department.

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick of Float glass panes of 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up with approved block laying polymer modified adhesive mortar all complete as per ADA instructions.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Galvanized iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge with 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles.

12 mm cement plaster of mix for Internal plastering with 1:4 (1 cement: 4 fine sand)etc complete as per ADA instructions.

Providing and laying vitrified floor tiles of size 600x600 mm with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc complete as per ADA instructions.

Size of Tile 600x600 mm (dadoing same as rough plastering )

Providing, fabrication and installation of Vista or Fenesta or Hunter Douglus make Manual operated Window Blinds, approved shade fabric including accessories, all as per OEM specification, etc complete as per ADA instructions.

Providing & rendering re-polishing of existing doors, double coat to get neat and even finish using spray machine similar to exist matt finish surface including surface preparation etc. complete, all as per OEMs specification. (MRFPUF coating).

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively complete as per ADA instructions.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm.

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade of One or more coats on old work.

Charges towards removing of Existing work station fabric panel Upolstry and fixing with new fabric Upolstry of 300Gsm. Cost with including transportation labour charges tools & machines etc., complete as per sample available at ADA.

Providing & Fixing of sun films to Windows after removal of existing unserviceable films to get neat and attractive finish, including surface preparation, cleaning the glass (both side), transport and labour cost etc. including clearing the debris from the site. All as per sample available at ADA.

Providing and Installing of Toughened Glass Door fitted on Existing fittings, glass panes shall be formed out of 12mm thick toughened glass. Cost including Frosted film, wastage, patch cut out, glass hole, Transportation, shifting. Size: 2090mm (H) x 1045mm (W) x 1nos. (Approx. 24 sqft)Providing and Installing of Floor spring, Top and Bottom Patch, Pivot Set, Lock with handle set etc complete as per ADA instructions.

Providing, fabricating & installation of overhead wall mounted wooden storage unit made out of 18 mm thick Plywood with open able shutters. External & internal surface finish with 01 mm & 0.80 mm thick laminate with glossy finish of approved shade respectively and all exposed side finish with 02 mm wooden edge beading, including all standard hardware such as lock, C type PC handles, piano hinges, locking arrangement and suitable nos of ‘L’ angles of required length to be fixed on wall for support neat and attractive finish, including transportation, shifting, labour etc., complete and all other details as per ADA instruction.

Finishing walls with textured exterior paint of required shade for Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm

Supply, and laying of Main Circuit, 2 runs of 4 sq mm+ 1 run of 2.5 sq mm flexible PVC insulated copper wire should be run in 1” casing N capping / PVC conduit pipe with connected accessories complete in all respect(For Power Point).

Supply, and laying of Sub Circuit, 2 runs of 2.5 sq mm+ 1 run of 1.5 sq mm flexible PVC insulated copper wire should be run in 1” casing N capping / PVC conduit pipe with connected accessories complete in all respect(For Power Point).

Supply and installation of 01 No. Of 5/15A power socket out let controlled by 20A single pole switch with indicator housed in single pole switch with indicator housed in PVC boxes, fixed at sitting desk as required by client.(8 modular switch plate with box, white colour, for RAW power points including internal wiring).

Supply and installation of 03 No. Of 5/15A power socket out let controlled by 20A single pole switch with indicator housed in single pole switch with indicator housed in PVC boxes, fixed at sitting desk as required by client.(8 modular switch plate with box, white colour, for UPS power points including internal wiring).

Supply and fixing of 2x2 feet 36W square LED fitting of false ceiling type and including necessary point wiring with switch control board accessories.

Supply and fixing of 2x2 feet 36W square LED fitting of false ceiling type and including necessary accessories.

Supply and fixing of 4 feet 20W LED tube and including necessary accessories.

Supply and installing following size of perforated Hot dipped Galvanized Iron cable tray (Galvanization thickness not less than 50 microns) with pergoration not more than 17.5% inconvenient sections, joined with connections, suspended from the ceiling with GI suspenders including GI bolts and nuts etc as required (300mm width X 50mm depth X 1.6mm thickness)

Supply, Installation, Commissioning and Testing of 2TR Capacity Cassette type Air Conditioning System complete with accessories like indoor unit, outdoor unit, cordless remote control and vidoflex insulation foam etc. including pressure testing, topping up of R410/407C gas, providing MS angle frame for mounting outdoor units (outdoor unit stand), Installation of Ac by inter connecting the suction & discharge pipe, laying the drainage pipe fixing the indoor unit & fixing the outdoor unit on the frame with necessary support & clamp, testing and commissioning units. Detailed specification of 2TR Cassette Type • Nominal cooling capacity • Power supply • Fan Type • Condensate drainage • Air Filter • Air Flow Volume • Noise Level •6000 Kcal/hr = 24000 Btu/hr •220-230 volts, 1phase, 50Hz •3Dimension Screw Fan 12000m3/hr •Built in water pump •Woven high density polyethylene •Four way Air flow -1200 m3/hr •44 db(A)

Supply of Suction & Discharge pipe Size 5/8” Copper for Suction & 3/8”for discharge to inter connect indoor & outdoor with necessary vidoflex insulation.

Supply and fixing of 1” dia PVC pipe including necessary fixing accessories for Drain pipe line.

Supply and Laying of 2.5 sq mm 6 Core PVC Flexible copper cable through PVC pipe to individual A/c indoor unit to outdoor unit including necessary fixing accessories.

Supply & Wiring 2 x 2.5 Sq mm wire in conduits or wire race ways. Supply & Wiring 1 x 1.5 Sq mm wire in conduits or wire race ways. (RAW Power DB to industrial plug top)

Supply and fixing of 4” PVC (Box Type) casing & capping for routing copper piping and drain piping. (Wherever required)

Supply and fixing of MCB 2 Pole: 20 Amp along with industrial socket plug & box charges including necessary termination of wires, testing and commissioning of the circuit.

Supply, Installation, Commissioning and Testing of 2TR wall mounting Split Air Conditioning System complete with accessories like indoor unit, outdoor unit, cordeless remote control and vidoflex insulation foam etc. charges including pressure testing, topping up of gas, providing MS angle frame for mounting outdoor units (outdoor unit stand), installation of Ac by inter connecting the suction and discharge pipe, laying the drainage pipe. Detailed specification of 2TR Cassette Type • Nominal cooling capacity • Power supply • Fan Type • Air Filter • Air Flow Volume •6000 Kcal/hr = 24000 Btu/hr •230 volts, 1phase, 50Hz •2Dimension Screw Fan12000 m3/hr •Woven high density polyethylene •Two way Air flow -1200 m3/hr

Supply of Suction & Discharge pipe Size 1/2” Copper for Suction & 1/4”for discharge to inter connect indoor & outdoor with necessary vidoflex insulation.

Supply and fixing of 1” dia PVC pipe including necessary fixing accessories for Drain pipe line.

Supply and Laying of 2.5 sq mm 4 Core PVC Flexible copper cable through PVC pipe to individual A/c indoor unit to outdoor unit including necessary fixing accessories.

Supply & Wiring 2 x 2.5 Sq mm wire in existing conduits or wire race ways. Supply & Wiring 1 x 1.5 Sq mm wire in existing conduits or wire race ways. (RAW Power DB to industrial plug top)

Supply and fixing of 4” PVC (Box Type) casing & capping for routing copper piping and drain piping. (Wherever required)

Supply and fixing of MCB 2 Pole: 20 Amps along with industrial socket plug & box charges including necessary termination of wires, testing and commissioning of circuit.

Supply and fixing of MCB Single Pole: 20 Amps (Existing Raw power DB)

Dismantling of Existing GI A/c duct of size 2feetX2feet to be removed and handed over to Electrical department (Approximate 30 RMT)

TThe premium executive table size shall be : 2400 Width mm x 1104 Depth mm x 735 Height mm. The top panel shall be 40 mm thick(18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster. The understructure shall be having legs made from 1.6 mm thick MS clad with the strips of MFC (Medium Density fiber). Hollow construction of legs facilitates wire management. The modesty & side panel should be 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer. Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). The Premium executive table ERU size shall be : 1400 Width mm x 580 Depth mm x 690 Height mm. The top panel shall be 40 mm thick (18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster. The understructure shall be having the modesty panel of 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer . Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). The Back unit size shall be of : 1860 Length mm x 580 Depth mm x 670 Height mm and the tower case of 1700mm Lengthx40mm Depthx1200mm Height. The door shall be 23 mm thick ( 18 mm thick Batons + 4 mm Veneer + 1 mm Backing Decorated ( BDL) ) . The Shelves and Partitions should be of 18 mm thick MDF( Medium density fiber) + Pigmented Black and coated with Melamine.

• Supply& installation Mid Back revolving chair without Tilting Mechanism. • The seat should be made up of 1.2 ± 0.1cm. Thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. • Back size:53.0cm.(w) x 73.0cm.(h) seat size:54.6cm.(w) x 49.0cm.(d) thehr polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkhrsteel and should be black powder-coated ( dft 40-60 microns ) the armrest assy. should comprise of three parts viz. the armrest support tube and p.u. armrest and the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm m.s.e.r.w. support tubes and chrome plated. The p.u. armrest should be made of black integral skin polyurethane with 50-70 shore hardness and reinforced with m.s. insert. The armrest top should be made of abs & upholstered with foam & leather the seat base assy. should be designed with following features: 360° revolving type without back tilt. It has an adjustment stroke of 12.0 ± 0.3cm the bellow should be 3 piece telescopic types and injection moulded in black polypropylene the pedestal should be made of die-cast aluminum with buffing finish. it should be fitted with 5nos. twin wheel castor. the pedestal should be 67.0 ± 0.5cm pitch-centre dia. (77.0 ± 1.0cm with castors) the twin wheel castors should be injection moulded in black nylon. • Overall Dimensions of Chair: Seat Height - min 43.4 to max 55.4 cm.Back Height - min 99.4 to 111.4 cm

Total Number of Seats in the Sofa Set: 2 Number of Single Seater Units (Nos): No Single Seater Unit Number of Two Seater Units (Nos): 1 Number of Three Seater Units (Nos): No Three Seater Unit Number of Four Seater Units (Nos): No Four Seater Unit Frame Covering: Fully Upholstered Sofa Set is Foldable to use as bed: No Backrest Cushion Material: Foam Density of Cushion of Backrest Material (Kg/Cubic M): 45 Covering Material for Seat and Backrest: Genuine Leather Frame Structure Material and size (±1 mm): Any other wood of minimum 25 mm thickness Seat Cushion Material: Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M): 40 Type of Spring in the Base / Seating: No Spring in the Base Length of Single Seater Units in mm (±5 mm): N.A Length of Two Seater Units in mm (±10 mm): 1560 Length of Three Seater Units in mm (±10 mm): N.A Length of Four Seater Units in mm (±10 mm): N.A Depth of Sofa Units in mm (±10 mm): 950 Sofa Height (Without Back Cushion) ±5 (mm): 800 millimetre Sofa Height (With Back Cushion) ±5 mm: 890 millimetre Seat Cushion Length ±5 (mm): 1080 Seat Cushion Width ±5 (mm): 520 Seat Cushion Thickness ±3 (mm): 210 Backrest Cushion Length ±5 (mm): 1150 Backrest Cushion Width ±5 (mm): 500 Warranty 5 - Years Total Number of Seats in the Sofa Set: 2 Number of Single Seater Units (Nos): No Single Seater Unit Number of Two Seater Units (Nos): 1 Number of Three Seater Units (Nos): No Three Seater Unit Number of Four Seater Units (Nos): No Four Seater Unit Frame Covering: Fully Upholstered Sofa Set is Foldable to use as bed: No Backrest Cushion Material: Foam Density of Cushion of Backrest Material (Kg/Cubic M): 45 Covering Material for Seat and Backrest: Genuine Leather Frame Structure Material and size (±1 mm): Any other wood of minimum 25 mm thickness Seat Cushion Material: Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M): 40 Type of Spring in the Base / Seating: No Spring in the Base Length of Single Seater Units in mm (±5 mm): N.A Length of Two Seater Units in mm (±10 mm): 1560 Length of Three Seater Units in mm (±10 mm): N.A Length of Four Seater Units in mm (±10 mm): N.A Depth of Sofa Units in mm (±10 mm): 950 Sofa Height (Without Back Cushion) ±5 (mm): 800 millimetre Sofa Height (With Back Cushion) ±5 mm: 890 millimetre Seat Cushion Length ±5 (mm): 1080 Seat Cushion Width ±5 (mm): 520 Seat Cushion Thickness ±3 (mm): 210 Backrest Cushion Length ±5 (mm): 1150 Backrest Cushion Width ±5 (mm): 500 Warranty 5 - Years

Supply & installation of Centre Coffee table with glass top, wooden legs 100 x 65 x 45 mm. • Overall Size : Width : 100cm Depth : 65cm Height : 45cm TABLE LEGS METERIALS: Colour :cherry • TABLE TOP MATERIALS & SIZE: (tempered Glass/ 10mm), L X W X T: 1000x650x10mm Colour: clear.

Supply of ‘L’ shaped Manager Table of size shall be 1650mm(L) x 750mm(D) and Return Table 1200mm(L) x 450mm(D) with one side attached Frame of Fabric Magnetic and White board. Work top shall be made up of 25mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2mm thick PVC Edge band with glue of standard quality.The single side legs shall be used for supporting panels & work surface on one side only. Single side legs shall be fabricated by CO2 welding in MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm and this shall be coated with minimum 45 micron thickness of epoxy powder coating. Body Panel Structure: uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 or equivalent and shall have an average wall thickness of 1.2 mm and also powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall be comprises of L- Channels and it shall be made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. The 52.4 mm panel has more elaborate and flexible construction offering various functional and decorative finishes as well as cable management capacity.

Supply and Installation of Desking -Premium suite model of size 2350*2350*750mm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestals are provided with lock for security. The Back unit size shall be of : 2350 Length mm x 50 Depth mm x 1800 Height mm. made of 25mm thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC clipping. Grommet cut out provided at the top of the work surface for wire management. Handles are provided for ease of opening. Storage is provided with cam lock for security.

Supply and installation Desking -Premium suite of size 165*195*75 cm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Supply & Installation of Desking -Premium suite of size 180*210*75 cm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing & fixing of modular customized Rectangular work station of size 1200mm (L) x 600mm (W) x 1200mm (H) each, The table top made out of 25mm thick Pre-laminated particle board with PVC edge, the under structure made out of 25mm thick Pre-laminated particle board, Cable manager to be provided on the work surface and accessed through grommet cut out on the worktop, incl vertical movements of wires. Partition should be 75 mm thick , made out of PLB either sides , one number white board per person rest fabric magnetic, all bottom tile metal powder coated, partition height 1.20 m height with cable race ways at two level for drawing power / data / voice cable, height adjustable fixtures as per existing arrangement / shade. Stability of the structure individually and totally will be the responsibility of the vendor. All as per OEMs specification, Drawing 'A' sample available at ADA.

Overall Dimensions of Chair-Seat Height - min 49.9 to max 58.9 cm. Total Height - min 134.9 to 143.9 cm. Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm • Seat/back assembly: The seat should be made up of 1.2 ± 0.1cm. Thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. back size: 53.0cm.(w) x 95.4cm.(h) seat size:54.6cm.(w) x 49.0cm.(d) the hr polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkhrsteel and should be black powder-coated (dft 40-60 microns ) • Armrest assay: the armrest assy. should comprise of three parts viz. the armrest support tube and p.u. armrest and the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm m.s.e.r.w. support tubes and chrome plated. The p.u. armrest should be made of black integral skin polyurethane with 50-70 shore hardness and reinforced with m.s. insert. the armrest top should be made of abs & upholstered with foam & leather the mechanism should be designed with the following features: * 360° revolving type * seat back tilting ratio of 1 : 1.5 * Front pivot for tilt with feet resting on ground ensuring more comfort. * tilt tension adjustment. * 5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock should be released * Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking. it has an adjustment stroke of 9.0 ± 0.3cm the bellow should be 1 piece and blow moulded in black polypropylene the pedestal should be made of die-cast aluminum with buffing finish. it should be fitted with 5nos. twin wheel castor. the pedestal should be 67.0 ± 0.5cm pitch-centre dia. (77.0 ± 1.0cm with castors) the twin wheel castors should be injection moulded in black nylon.

• Supply & Installation of MID BACK CHAIR, the seat Material- Leather, Color – Black, Revolving Chair – Yes, SEAT/BACK ASSEMBLY: The seat is made up of 1.2 +0 1cm thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam The back is made up 1.2 TO 1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam The back ply and foam is designed with contoured lumber support for comfortable seating posture * MID BACK SIZE 48.5 cm (W) X 64.5 cm (H) * SEAT SIZE 51.0 cm (W) X 48.0 cm (D) • HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back is moulded with density = 45 +/-2 kg/m* and Hardness load 16 2 kgf as per IS 7888 for 25% compression • ARMRESTS (ADJUSTABLE):The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of B3 81z0 03 cm x 0 2-LO 01 cm thk M S E R W tube having chrome plated finish The armrest height adjustable up to 6 5z0 Scm in 5 steps • KNEE TILT SYNCHRO MECHANISM WITH SEAT DEPTH ADJUSTMENT * 360° revolving type Single point control * Single point control * Front pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment * 4-position locking with anti-shock feature Seat back tilting ratio of 1.2 * Seat depth adjustment of 6.0 +0 Scm can be locked in 6 positions • FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features * 360° revolving type Single point control * Front pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment * 4-position locking with anti-shock feature * knockdown condition vacations within +1 0 cm • ADJUSTABLE BACKREST: The back rest is connected to the mechanism with a drop-iift mechanism which can be adjusted in the range of 7.0 IO.5cm. And locked in 5 positions for the better lumbar support. • FIXED SPINE (COFERENCE/ VISITOR): The seat and back are arrested together with fixed type spine i.e no back up/down adjustment; made of 0.8 TO.05 cm thk HR Steel and is black powder-coated ( DFT 40-60 microns ) • HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.010.3 cm. • PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 0.02 cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.010.Scm. Pitch-centre dia. (76.011.0 cm with castors). • TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.

Supply & installation of High Back Pure leather revolving chair of size approximately 76.10L x 76.10D x 114-131.50H CM and seat height 44.50-54.50cm. The chair made by Leather high back chair, Back profile can be adjustable, Active Bio-synchro Mechanism. The chair comes with 5 position tilt limiter.

Supply & installation of Mid Back Pure leather revolving chairs for visitors size approximately 76.10L x 76.10D x 96.50-114H CM and seat height 44.50-54.50cm. The chair made by Leather high back chair, Back profile can be adjustable, Active Bio-synchro Mechanism. The chair comes with 5 position tilt limiter.

Supply of MID BACK CHAIR of Overall Dimensions shall be Chair-Seat Height - min 43.3cm to max 54.3cm. Height - min 89.5cm to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3cm and Depth- 76.3cm.Seat assembly: The seat assembly shall be made up of 1.2 ±0.1cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. Seat size: 47.0 cm. (w) x 48.0 cm. (d) Back assembly: The backasembly. shall be made of powder coated (oft 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2±0.016cm.thick. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using double layer spacer mesh fabric with high tenacity yarn. Back size : 46.5 cm (w) x 60.5 cm (h).High Resilience (HR) polyurethane foam: The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.Armrests: The one-piece armrests shall be injection moulded from black co-polymer polypropylene. Centre-Tilt mechanism: The mechanism shall be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • upright position locking. tilt tension adjustment. Pneumatic height adjustment: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.Telescopic bellow assy: The bellow shall be 3 piece telescopic type and injection moulded in black polypropylene.Pedestal assembly: The pedestal shall be injection moulded in black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm. Pitch-center dia. (76.3 ±1.0cm with castors.)Twin wheel castors: The twin wheel castors shall be injection moulded in black nylon etc.

Supply of Mid Back Chair of size shall be : SEAT SIZE (Larger Seat Depth) : 47.00cm (W) x 51.50cm (D), SEAT SIZE (Standard Seat Depth) 47.00cm. (W) x 49.50cm.(D), BACK SIZE : 45.00 cm(W) x 65.3cm(H).The seat shall be made up of 1.2 + 0.1cm thick hot pressed plywood. The Back shall be made up of injection moulded glass filled nylon & upholstered using Mesh fabric with high tenacity yarn. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam shall be moulded with density 45+/-2 kg/cum and hardness 16 + 2 kgf as per IS:7888 for 25% compression.ARMRESTS : The adjustable armrest shall be designed with the following features:Up-Down adjustment— 8 steps (8 0+0.Scm range).Height adjustable armrest structure which shall be powder coated & fitted with an armrest top.Fixed Armrest Top shall be PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side. Lumbar pad shall be an adjustment of 8.0 + 0.5 cm in height.

SEAT/BACK ASSEMBLY: The seat is made up of 1.2 * 0 fern thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 The Back is made up of injection moulded glass filled nylon & upholstered using Micro mesh fabric with high tenacity yarn with 28 density foam Sandwich in lumbar area. * SEAT SIZE(Larger Seat Depth) : 47.0 cm. (W) x 51.5 cm (D) * SEAT SIZE(Standard Seat Depth) 47 0 cm. (W) x 49.5 cm. (D) ” BACK SIZE : 45.0 cm. ”(W) x 65.3 cm. (M) HIGH RESILIENCE (HR) POLYURETHANE FOAM The HR poly methane seat foam is moulded with density 45+/-2 kg/m"" and hardness 16 + 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the folIowing features » Up-Down adjustment— 8 steps (8.0+0.Scm range) • Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad Lumbar pad has an adjustment of 8 0 + 0.5 cm in height.FRONT PIVOT SY!’JCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features.

Supply & installation of High Back Pure leather revolving chair of size approximately 75L x 75D x 102-119H CM and seat height 45-55cm. The chair made by Leatherette high back chair, Back profile can be adjustable, knee tilt synchro Mechanism. The chair comes with 3 position tilt limiter.

Providing, fabrication and Installation of Conference Table - 4800L x 1500 D x 750 H Table. Cable Tray & Vertical Cable riser will be provided. 25mm Thick Prelaminated Board Table top with 2mm Thick PVC Tape Edge Banding. Table will have 3 Nos Flip Cover and Electrical Cutout provisioning Cable Tray. Charges included transport and shifting etc complete as per OEM specifications and directed by engineer-in-charge. The design of the table is confirmed by the ADA.

Providing and fixing of 3 Drawer Mobile pedestal of size 314(l) x 400(w) x 80(h) and 22.5(h) all as per OEM Specification and sample available at ADA.