Central Food Technological Research Institute Tender

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Hacking of CC flooring, masonry wall and ceiling including removing existing bituminous paint, cleaning for surface, removing loose particles etc. complete as per direction of the Engineer-in-Charge.

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 M sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5.00 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 M sand)

Providing and laying vitrified tiles in floor in different sizes (Minimum thickness of 10 mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement : 4 M sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified tiles Matt/Antiskid finish of size Size of Tile 600x600 mm MAKE: SOMANY/ KAJARIA/ RAK/ NITCO

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 M sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm MAKE: SOMANY/ KAJARIA/ RAK/ NITCO

Providing and fixing Single Leaf Door (Clean Room Doors): Single leaf Door fit into the wall. Shutter sheet thickness will be 0.8mm and frame will be 1.2mm thick made up of GPSP GI sheet with epoxy polyester powder coating. Leaf thickness will be 44mm and infill will be PUF with density 40±2 Kg/m33. Door bottom seal shall be provided. Single Leaf Door Accessories: 03 No. SS Roll bearing Hinges, 01 No. Door Closer, 01 No. SS D Handle Back-to-back, 01 No. Double glazed view panel of 450*600 mm with 5 mm thick toughened glass, 01 No. Drop Seal, 01 No. Lock and 01 No. Kick plate Door Size: 1100 x 2100 mm

Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles having minimum wall thickness of 1.70mm for series R1 & R2 profiles and 2.10 mm for series R3 and R4 profiles conforming to EN: 12608 in any shape colour and design duly reinforced with galvanized mild steel section made of required shape and size as per CPWD specification, uPVC extruded glazing beads, interlocks and inline sas adaptor (where ever required) of appropriage dimension, EPDM gasket, hardware SS 304 grade fasteners of Minimum 8mm dia with counter sunk head, comprixing of matching polyamide PA6 grade sleeve for fixing frame to finished wall as pr IS1367: PART 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duty sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc., After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specificaton and direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately. Note: Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed 45 m/ sec as per IS875 - part3 (ii) sits with structure height morethan 20m for all wind speeds Fixed window/ ventilator without mullion/ transom. Using R1 series with frame (33mm and above) x (35mm and above) (Height upto 0.90 metre) Make: Qute/ NCL/ VEKA/ Komarling

Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles having minimum wall thickness of 1.70mm for series R1 & R2 profiles and 2.10 mm for series R3 and R4 profiles conforming to EN: 12608 in any shape colour and design duly reinforced with galvanized mild steel section made of required shape and size as per CPWD specification, uPVC extruded glazing beads, interlocks and inline sas adaptor (where ever required) of appropriage dimension, EPDM gasket, hardware SS 304 grade fasteners of Minimum 8mm dia with counter sunk head, comprixing of matching polyamide PA6 grade sleeve for fixing frame to finished wall as pr IS1367: PART 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duty sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc., After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specificaton and direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately. Note: Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed 45 m/ sec as per IS875 - part3 (ii) sits with structure height morethan 20m for all wind speeds Two and half track three panels sliding window with two glazed and one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS304 body Using R2 series with frames (65mm and above) x (40mm & above) and glazed sash (25mm & above) x (50mm & above) and fly screen sash (18mm & above) x (40mm & above) with zinc alloy (zamak) powder coated touch locks with hook (height upto 1.2 metre) Make: Qute/ NCL/ VEKA/ Komarling

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (Plain /Pin Headed glass) MAKE: SAINT GOBIAN OR MODI

Providing and fixing SS wire guage (Grade - 304) fly proof mesh (or mosquito mesh) of thickness 0.5 mm dia to 0.63 mm dia of average width of aperture 1.4 mm or less (as decided by the engineer incharge) in UPVC window shutters with necessary screws, fittings etc.,

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/ litre MAKE: asian or its equivalent

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic ompound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats Recommended brand: asian/NEROLAC

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead for all lead upto 10 kms including all lifts involved.

ELECTRICAL WORK

Supplying, Installation, Testing & Successful Commissioning of 36 Watts 4 Feet LED Batten Light (Day Cool) complete with internal wiring, 1 metre length of any standard make rated 3 core copper wire etc.,, ready to use suitable to fix on wall / ceiling and to work with 230V Single Phase, 50Hz AC Supply. The end wire from the fitting shall be terminated to a 2 Way 5Amps PVC Connector and to connect to the existing point. Make: Please refer Special Electrical Conditions under Tender Document File.

Supplying, Installation, Testing & Successful Commissioning of 16 PVC Modular Box along with Modular Base, Cover Plate etc., in recess / wall using suitable hardwares etc., as per directions of Engineer In-Charge and consisting of following Modular items a) 5/6 Amp Switch - 2 Nos; b) 6 Pin 5/6 Amp Socket Outlet - 2 Nos; c) 15/16 Amp Switch - 2 Nos; d) 6 pin 15/16 Amp Socket Outlet - 2 Nos and e) 20 Amps, 2 Pole, "C" Curve, 10kA, 230V Mini MCB - 1 No. Internal wiring for 5 Amps Switch & Socket with 2.5 sq.mm FRLS Multistrand, Single Core Copper Wire; for 15 Amps Switch & Socket with 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire; Loop Earthing for Sockets with 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire. Red, Black and Green Colour for Phase, Neutral and Earth respectively. All the wires to terminate using suitable size Copper Lugs etc., as required. Make: Please refer Special Electrical Conditions under Tender Document File.

Supplying, Installation, Testing & Successful Commissioning of 63 Amp, 415V AC, 4 Pole RCCB, having 30mA sensitivity "C" Curve, 10kA fixed in a suitable size Metal Box (painted with primer and paint) on wall with necessary hardwares etc., including connections etc. as required. Make: Same as Item No:2.02

Supplying, Installation, Testing & Successful Commissioning of 100A, 30kA, 415V AC, 4 Pole MCCB with thermomagnetic release and terminal spreaders fixed in a suitable size Metal Box (painted with primer and paint) and to fix on wall with necessary hardwares etc., including connections etc. as required. Make: Same as Item No:2.02

Supply, Installation, Testing and Successful Commissioning of 12 Inch Dia, 300 mm sweep, industrial type ready to use Exhaust Fan having Bird Cage with 1.5 FRLS PVC insulated, copper conductor, single core cable and to fix with required size of MS frame duly painted with one coat of primer and 2 coats of paint, suitable hardwares etc., and provide one no. of 3 Pin 5/6 Amps ISI make Socket along with Gangbox and 3 Pin 5/6A Amps ISI make Plugtop as required. Make for All: Please refer Special Electrical Conditions under Tender Document File.

Labour charges for digging 8 feet of depth below ground level, including hard soil, rocks, cement surface etc.,if any encountered, fixing the Item No:2.15, refilling of soil etc., as required. (along with charcoal / coke and salt from S.No:2.15 as required, already estimated under S.No.2.15).

Dismantling & taking down Old light Fittings / related wirings, hardwares etc., after carefully disconnecting the incoming electrical input and insulating the same, depositing all the old materials in an organised manner to the Auction / Electrical Section Store Yard or as per the advise of the Electrical Officer In-Charge of the Project without any damage.

Group A Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Make: Please refer Special Electrical Conditions under Tender Document File

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Same as Item No: 2.08 for Wire and Pipe. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size. a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Same as Item No: 2.08 for Wire and Pipe. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size. b) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Same as Item No: 2.08 for Wire and Pipe. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size. c) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Same as Item No: 2.08 for Wire and Pipe. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size. d) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. Make: Same as Item No: 2.02

Supplying and fixing 30A, 415V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioing etc. as required. Make: Same as Item No:2.03

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. Note: Masonry enclosure size is 1.5 Feet x 1.5 Feet x 1.5 Feet. As per IS 3043, charcoal/ coke and salt should be refilled with 50 Kg each per earthpit. The copper plate has to be tinned, connected copper flats have to be brazed and only SS nut, bolts and washers to be used.

Providing and laying earth connection from earth electrode with 4.00mm dia copper wire in 15mm G.I. pipefrom earth electrode including connection with copper thimble excavation and refilling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.