Bengaluru Water Supply And Sewerage Board Tender

a03 - Earth work excavation for pipeline trenches by mechanical means as per drawing and technical specifications, including setting out, construction of shoring, strutting, barricading, caution lights, bracing, using sight rails & bonding rods at every 100 mm wherever necessary as directed, removal of stumps and other deleterious matter, dressing of sides and levelling the bottom of trench to the extent required , utilising the available excavated earth locally for the work and all other appurtenances to complete in the following strata.Ordinary/soft rock (without requiring blasting) Depth upto 1.50m

a03.1 - Depth exceeding 1.5 m, but not exceeding 3 m

a04 - Earth work excavation for pipeline trenches by mechanical means as per drawing and technical specification, including setting out, construction of shoring, strutting, cost of blasting materials, barricading, caution lights, bracing, using sight rails & bonding rods at every 100 mm wherever necessary as directed, removal of stumps and other deleterious matter, dressing of sides and levelling the bottom of trench to the extent required , utilising the available excavated earth locally for the work and all other appurtenances to complete in the following strata.Hard rock (blasting prohibited) Depth upto 1.50m

a04.1 - Depth exceeding 1.5 m, but not exceeding 3 m

a05 - Excavation of Hard Rock by diamond rope cutting method using diamond rope,line draw machine,making holes by drilling machine for breaking the block by means of hydraulic breakers/splitters without any means of blasting or use of explosives,etc.,complete as per specification and directions of the Engineer-in-Charge.

a06 - Providing and installing sheet piling for both sides of the trenches for following depths with mild steel sheets of not less than 6.5mm thick, stronger knife edge, recessed spreader sockets, 3 inch single or double wall shields, to be designed by the contractor to withstand all types of soils, maximum depth as per the approved design drawings, including labour charges for installing and removiing the sheet piling at various reaches of sewer line constructions, including loading, unloading, transporting to the suitable location etc. complete with all lead and lifts. (Measurement shall be taken for one side only eventhough it is provided for both sides. For depth upto 3.0 m

a07 - Providing and Filling in foundation with granite / trap broken metal 100mm and down size with approved M-Sand including hand packing, ramming, watering including cost of all materials and labour with all lead and lift complete as per specifications

a08 - Supplying S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level includingloadingandunloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey.RCC NP3 Class pipe of 1400mm dia.

a08.1 - RCC NP3 Class pipe of 300mm dia.

a09 - Excavating of ramming/jacking/driving pit and receiving pit of size 5.00m(length) x 3.00m (breadth), up to 6.00 m depth in all soil strata including shoring and strutting including cutting of Asphalt/CC/Mac adam road surface and removing the excavated stuff with all lead and lifts. The work includes formation of CC/RCC of 1:3:6 with or without 20mm steel with suitable spacing. The work also to receive the impacts driving pushing operation of encasing pipe. The cost includes driving the horizontal bore by pushing/jacking methods (trenchless technology method) by using construction agencies' cranes, jacks, jacking materi als, generator, welding machineries, compressor, jack hammer and other equipments etc., without interfering and causing any hindrance to the movement of traffic or any other vehicles, without any disturbances to the railway/road/canal formation etc., The cost also includes bailing / pumping of water where ever necessary without affecting any installation like water supply and sanitary pipeline/telephone cable, electric cables etc. The work comprises of water for curing, carriage and fixing charges, concrete up to plinth for erecting and conducting the hydraulic push ing arrangements apart from passing through and scooping the earth inside the pipes and pit and depositing and disposing the surplus earth to a designated/ approval place and levelling the site after completion of entire work as directed by Engineer in Charge. The rate is excluding the cost of MS pipes.size up to 5 mts X 3 mts - depth up to 5 mts

a10 - Installation of product pipe by manual jacking method - Manufactur ing, providing, transporting, rolling, lowering, laying & jointing, testing, commissioning of ERW (Electric Resistance Welded), SAW (Submerged Arc Welded) MS pipe (Fe-410 grade) conforming to IS 3589-2001 with latest ammendments including perfect linking welding of joints to correct position including cost and conveyance of pipes and materials with all lead ,lift, cost of labour, loading and unloading of pipes for the following diameters with specified thickness of plate as noted below including bailing out of water wherever necessary for laying of carrier pipe of suitable dia including inside and outside of casing pipe painted with two coats of Anti corrossive tankmastic paint. Installation of steel pipe by Ramming / Jacking method to cross Railway track / NH /BDA /BBMP/Other roads/Existing utilities / NALA crossings, filling the gap between casing pipe and carrier pipe with quarry grit using compressor with all necessary equipments, plants etc, complete. Suitable spacers of HDP/MS or other similar material should be provided in between carrier & casing pipe to prevent carrier pipe forming metallic contact with casing pipe. Note : a. The cost of jacking is inclusive of cost M.S. casing pipe of specified thickness b. The cost of carrying pipe is separate and provision shall be made as per site requirement c. The cost of Jacking includes all leads lifts, cost of consumables, fuel charges, labour. d. The cost of jacking and receving pits shall be proposed seperatelly as per site requirement.Jacking of 2000 mm dia & 16mm thick M.S. Casing Pipe

a11 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50m, and lift upto 1.5m including cost of all labour complete as per specifications.

a12 - Spreading of Stone Dust : Supplying and providing stone dust in the station yard or wherever required including watering, ramming, consolidating and dressing. The rate includes the cost of material, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineer-in-charge of works as per the standard procedure.

a13 - Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead. Dismantling Stone Masonry, Rubble stone masonry in cement mortar

a14 - Providing Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with

a15 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications.M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates

a15.1 - Additionalities for Formwork

a16 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. All other type of structures

a17 - Construction of RCC Machinehole chambers of 1:1.5:3 proportion or approved type Cast-insitu/Pre-cast RCC Machinehole chambers, constructed using form vibrators of standard type, with barricading, danger lighting and using of sight rails and boning rods wherever necessary, shoring and strutting wherever required using Ordinary Port Land Cement, using 1:1.5:3 proportion RCC with 20mm and down graded jelly, well graded sand and steel of approved quality, 200mm thick top concrete slab, having wall thickness and raft thickness as in approved drawings and with an offset in raft alround the chamber as in approved drawing, benching concrete with 1:6 slope towards the central drain finished smooth, including fixing and grouting of pipes, including conveying to work spot supply and fixing SFRC Machinehole cover and frame (Heavy duty) conforming to IS:12592 with latest amendments, on a bed of CC 1:2:4 Providing and fixing of minimum 3mm thick encapsulated plastic footsteps (as per IS 10910) on 12mm dia. Grade Fe-500 steel bar (as per IS 1786) staggered at 300mm apart as detailed in Technical specifications, including stone grit beding wherever required, watering, curing, engraving Machinehole number with flow direction on the inner cylindrical surface etc., complete including cost of reinforcement steel and fabrication charges and also cost and conveyance of all materials, labour with all lead and lifts. The Pre-cast RCC Machinehole are for various diamters and depths as stated below and as per detailed drawings, specifications and direction of the Engineer-Constructing Pre-cast RCC Machinehole 1.2 m internal dia. , 2.0M depth & SFRC cover & fram

a17.1 - For Every 0.1m depth 2.00 to 3.00m

a17.2 - Constructing Pre-cast RCC Machinehole 1.8 m internal dia. , 3.0M depth & SFRC cover & fram

a17.3 - For Every 0.1m depth 3.00 to 4.00m

a17.4 - Constructing Pre-cast RCC Machinehole 1.8 m internal dia. , 4.0M depth & SFRC cover & fram

a18 - Dismantling the damaged or collapsed Machinehole ,conical in shape, and reconstructing the same for the same dimensions, with machine made wire cut brick in CM 1:4 with ordinary portland cement etc. as per design and specifications. The existing ring, cover and CC beeding to be used. For 1.2M dia For Machinehole of 1.2M dia and 2.0 M depth

a19 - Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work

a20 - Providing, filling and laying of sand bags filled with sand / clay for diversion of sewage during execution of work.

a21 - Dewatering the sewage / storm water by using reqired HP submersible pump for the diversion of storm / sewage during the execution of work. Considering for one Pump.10 hp pump