Medical Health And Family Welfare Department Tender

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with free lead as per Technical Specification Clause 303.1.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000m as per Technical Specification Clause 303.1.

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepare surface,mixing by mix in place method with rotavator at OMC,and compacting with smooth wheel roller to achieve the desired density ,complete as per Technical Specification Clause 401. With Grading - III material (crushed stone aggregate)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. (Using Screening Crushable type materials such as stone aggregate by Machanical means).

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (UsingScreening Crushable type materials such as stone aggregate by Machanical Means).

Providing & laying 50 mm thick builtup spray grout over W.B.M. surface including cleaning the surface, heating bitumen to required temperature, applying prime & tack coat @ 10 kg / 10 M2 and also including cost of buitmen and stone aggregates confirming to physical properties and grading given into the M.O.S.T. table 500-7 (3rd revision) spreading stone metal @ 0.66 M3 / 10 M2 in layer, hand packing, rolling, compacting and then applying spray of bitumen @ 15 kg / 10 M2 Finishing with key aggregate @ 0.13 M3 / 10 M2 in proper grade, camber or superelevation and rolling the same with power road roller and finishing the surface with template, including the cost of light, barrier, danger single and chowkidar, making and maintaining diversion including cost of all labours, cost to P.O.L. and all other lubricants and also hire charges of road roller with DMR all complete job as per specification and direction of E/I.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A as per Technical Specification Clause 510.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.

Reinforced cement concrete M15 grade Ordinary kilometre stone (precast) stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703.

Providing and fixing of informatory Signboard with 'Logo' as per specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc will be painted with ready mixed synthetic enalel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour, Supported and welded on 47mm x 47mm of 12 SWG Square tube of 3050mm height duly strengthened by 25mm x 5mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per approved drawing and Technical Specification Clause 1701.

Earth work inexcavation for structure as per drawing and technical specification clause 305.1 including setting out, construction of shoring and brading, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (with manual means in ordinary soil & Depth upto 3m)

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specification clause 802, 803, 1202 & 1203 (P.C.C.grade M-15 in open Foundation)

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 Course rubble masonry work in CM 1:4 in foundation in culverts.

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 Random Rubble masonry work in CM 1:4 in foundation in Drain & in Retaining Wall.

Stone masonry work in cement mortar in sub-structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Coarse Rubble masonry work in CM 1:4 in sub-structure in culverts.

Stone masonry work in cement mortar in sub-structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Random Rubble masonry in CM 1:4 in sub-structure in Retaining Wall.

Plain/Reinforced Cement Concrete in substructure complete as per Drawing and Technical Specifications Clause 802, 804, 805, 806, 807, 1202 and 1204. (P.C.C. Grade M-15 in Coping.

Plain/Reinforced Cement Concrete in substructure complete as per Drawing and Technical Specifications Clause 802, 804, 805, 806, 807, 1202 and 1204. (P.C.C. Grade M-20).

Providing and laying reinforced Cement Concrete in super structure as per drawing and technical Specifications Clause 800, 1205.4 and 1205.5 (P.C.C. Grade M-25 in Deck Slab).

Providing and laying Cement Concrete waering coarse M-30 grade including reinforcement complete as per drawing and technical Specifications Clause 800 and 1206.3.

Supplying, fitting and placing TMT bar reinforcement (Fe 415) in sub-structure complete as per drawing and technical specifications. Clauses 1002, 1005, 1010 & 1202

Providing weepholes in brick masonary/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1 (V):20 (H) towards drawing face complete as per drawing and technical speciication Clause 614, 709, 1204.3.7

Pointing with cement mortar (1:3) on brick or stone masonary work as per drawing and technical specification Clauses 613.4 and 1204.

Plastering with cement mortar (1:4) 15mm thick on brick work in parapet as per technical specifications Clause 613.4 and 1208.4

Back filling behind abutment, wing wall and return wall complete as per drawing & technical specification Clause 1204.3.8 (With Sandy Material)