Drinking Water And Sanitation Department Tender

Supply, Installation and commissioning of Power control cum distribution cubical LT panel board, made of 2 mm thick, MS sheet of suitable size, dust & vermin proof consisting of Bus bar – 4 pole 630 A 415 v copper strip bus bar enclosed in MS sheet Incoming feeder – 630 A TPN 415 V MCCB thermal release range, adjustable and breaking capacity with rotary operating mechanism handle – 01 no., Outgoing feeder – 500 A TPN 415 V MCCB thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/ Siemens/ Jyoti – 02 no. and 01 no spare feeder. all complete job. Voltmeter (0-500) V voltmeter with selector switch - 02 nos. Ammeter – (0-200) A C.T operated with selected switch 02 nos. Indicating lamp 01 set. 32 A MCB for light load 02 nos. Panel should be duly painted with two coats super enamelled paints of approved colour one coat of red oxide primer and including all internally wired with suitable size of copper control wire/cable etc. all complete.

Supplying XLPE / PVC insulated 240 mm² 3.5 core Aluminium armoured cable 1.1 KV grade. Make- polycab/Havells/ Mecab .

Supplying XLPE / PVC insulated, unarmoured copper cable 95 mm² 3 core 1.1 KV grade.Make- polycab/Havells/ KEI

Providing and erecting of Indoor Termination kit for 1.1 KV XLPE screened 240 mm2 3 core cable. Make-ISI

Providing and erecting of outdoor Termination kit for 1.1 KV XLPE screened 240 mm2 3 core cable.Make-ISI

Cost towards Supplying & fitting all labour tools & tackles for making common header of heavy duty M.S pipe of Suction side and delivery side jointing header to rising pipe including all required size such as MS pipe, flanges short piece, bend, allied materials including cost of cutting, welding, threading etc. required for the job.

Supplying, Installation, commissioning and testing of Triple spur gear type chain pulley block suitable for 3 ton capacity with 6 m lift complete with load chain and hand chain suitable for above lift tested for 50% overload as per IS 3832 carrying ISI mark.

Providing and fixing square bar EN 8 as rail over head crane on provided track, girder/ continuous corbel beam, including supporting plate and “J” bolts.

Supplying, Installation, Testing & commissioning of outdoor type 250 KVA 11/0.433 KVA Copper wound Distribution transformer with offload tap changer 12.5% to 2.5% in step of 2.05%, continuously rated for three phase, 50 Hz, full load and temperature rise not exceeding 45ºC by thermometer in oil and 50 ºC by the resistance in winding after continuous run at full load rating, the transformer should have oil immersed winding having vector group of DY11, HT side connect in delta & LT side connect in star with neutral brought out connected. The transformer should have power terminal bushing arrangement on HT side & cable box in LT side with standard fitting for mounting of transformer with first filling of transformer oil including all accessories etc. Transformer shall be latest manufacturing standerds as per amended IS specification and the load & NO losses shall be limited to the values given or as per IS or Norms issued by JSEB.all complete with all materials. Make Kirlosker/ Synergy/ Servocon.

Electric substation – Cost of construction of DP structure for transformer, supplying and erecting steel tubular pole, top bracket channel, back clamp, 11 KV disc insulator with hardware, earthing set complete. MS nut and bolt, MS angle, GI wire, clamp for transformer base , top channel, AB switch, D.O fuse angle , stay set complete 11KV lightning arrester, etc complete as per the site requirement all complete.

Earthing with copper earth plate 600mm x 600mmx 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (but without charcoal or coke and salt)

Supplying and fitting light wiring inside and outside P/Plant by doing short point light wiring - 6 points, long point 3 points, 60W LED light 4 Nos., 140 W LED street light 3 no. including Labour charge & cost of copper wire, PVC tape, PVC pipe, bend & other materials all complete.

S/L 25 mm X 6 mm thick G.I strip at 0.50 m below ground as strip earth electrode,including soldering etc.as required.

Supplying, Installation and Commissioning of centrifugal pump self-priming mono block pump set for dewatering having discharge 2600/600 LPH and head 6/30 meter operated on single phase 50 Hz, 220 ± 6 % volt 2800 RPM. Suitable size suction pipe, delivery pipe Kirlosker / Crompton greaves and any ISI reputed make

Supplying installation and erecting of lightening arrester at pump house of approval make and fire extinguisher, hand gloves & First aid box etc.

Supplying, installation & commissioning, testing of double girder hand operated rectangular 10 ton capacity travelling trolley tested on 50 % over load on existing girder (span 37 ft ) for cross travel along with 6 meter chain arrangement on the existing longitudinal joist both sides of W.T.P. Rukka pump house deducting the cost of taken out scrap materials.

Supplying, installation & commissioning, testing triple spur gear type chain pulley block 10 ton capacity with 6 meter lift complete with load chain and hand chain suitable for above lift tested on 50 % over load as per IS 3832 .

Supplying, installation & commissioning, testing of double girder hand operated rectangular 5 ton capacity travelling trolley tested on 50 % over load on existing girder for cross travel along with 6 meter chain arrangement on the existing longitudinal joist both sides of W.T.P. Rukka pump house deducting the cost of taken out scrap materials.

Supplying, installation & commissioning, testing triple spur gear type chain pulley block 5 ton capacity with 6 meter lift complete with load chain and hand chain suitable for above lift tested on 50 % over load as per IS 3832 .

Cost towards repairing Rail trolley with changing of damaged parts bearing , bearing cover, gear, shaft , etc as required including welding , machining and repairing rail track on both side of overhead crane.

Cost towards making platform for maintenance pump sets and accessories with supply of heavy duty steel sheet 165 ft sq. 5 mm thick and changing damaged strip by new50 mm wide x 6 mm thick x75 “ long steel strip -30 nos. as where as required including cost of welding, cutting , repairing railing

Design, supply erection and commissioning of cable tray in old W.T.P. Rukka Pumping plant for 6 Nos. 11 KV motors 1½ ft wide x 360 ft long with 50 mm wide x 6 mm thick steel strip 4 nos. running in hole tray and cross strip as where as required , M.S channel 3” size x 2 ft long average – 68 Nos. . M.S channel 6” size x 2 ft long average – 68 Nos. including cost of fixing in wall ,welding ,cutting, labours, tools and keeping insulating rubber insertion in tray.

Supplying, laying, commissioning, testing of 185 mm2 3 core Al. conductor XLPE 11 KV grade armored cable PVC sheathed and PVC insulated from VCB to 11 KV HT motor on cable tray

Supplying and fitting ,testing 185 mm2 3 core termination Kit indoor type with all labours, tools and technician on 11 KV grade of 185 mm2 3 core Al. XLPE cable and joining with motor terminals to panel, etc. all complete

Supplying and fitting 4’’ dia. Heavy duty conduit P.V.C pipe for 11 K.V cable laying with bend ,socket ,clamp, etc. as required for 6 Nos. 11 KV motors.