Central University Of Jharkhand Tender

Supply and installation of lab-island table 3000L x 1500W x 900H (mm) with reagent rack consisting of R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright Common 900 Ht.C-Frame Assy. For Table Depth 1540 Island With Upright 750 Module Length Horizontal Members, 1500 Module Length Horizontal Members, 1540 Depth Island With Upright & Without Upright End Cover Panel, Master Upright With L.H.Side Cutout Island Without Upright C-Frame Joining Bracket, Fixed Type Reagent Shelf (Main Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only), WFU-2S-1D-750W-635H, Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D), 3 Way Faucet Bench Mounted 3 Way Water Fittings 8" Swing Gooseneck Model No. : 259924110 01 - 08, Double Valve,Turret,1-Hole,Fix.Nozzle, Press-LPG Model no: 25321091012-14, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, 6 MM Self Adhesive Natural Rubber Strip, Silicon Sealant - Black, Masking Tape, Master Upright Extenstion, Flexible/F Serated Connector Model : Hp 01 Make: Premier, Anti-Siphon Bottle Trap Model : S 04 Make: Premier, 6/16A, 6 Pin Shutter Socket - Model No: M1332, 6 Module Plate - Model No: Cs956M-S, 16A, 1 Way Switch Model No: M0130 as per direction of Engineer in charge.

Supply and installation of Storage cabinets which are designed to safely store highly corrosive acids. With a full PP construction, the Resilience cabinets are completely protected from corrosion, making them the preferred choice in labs and workspaces dealing with aggressive chemicals. Resilience provides you with a storage solution that easily outperforms the metal and wooden storages. Dimension of Resilience Storage Cabinet is 1000W x 1500H x 486D mm. All safety claims of this product are backed by third party certification for Chemical Spot Test for 49 chemicals listed in SEFA standards and used across various industries. The cabinet has been designed to be fully ventilated ensuring air circulation and preventing a build-up of dangerous fumes within the cabinet. The shelves comprise of removable height adjustable collection trays that are leak-proof, enhancing the safety factor of the storage units. Exhaust Provision: There is an air-duct at the back, inside the cabinet that effectively extracts fumes when connected to exhaust. Louvers are provided on the front doors to allow inward Low of fresh air. Zero-Corrosion: Full Polypropylene Body, with no exposed metal hardware, ensures there is no corrosion. Closing mechanism: The cabinet has a latch to ensure proper shutting of the doors. Removable & Height- Adjustable PP Trays as Shelves: the PP Collection Trays can be removed easily, and can be height-adjusted as required. Load Bearing Capacity & Spill Containment: Each shelf can take up to 30 kgs (approx) of uniformly distributed load. The shelves are leak-proof and fully contain accidental spillages. Locking Provision: The door has provision for using a padlock to safeguard the contents of the cabinet as per direction of Engineer in charge.

Supply and installation of emergency eye, eye/face wash, safety stations and drench hose units with spray-type outlet heads to deliver a soft, wide, high volume spray of water. Outlet heads should have an internal self-regulating flow control, a reticulated polyurethane filter, a threaded spray cover and a hinged swing-away dust cover. Hinged cover should be permanently attached to outlet head body with a stainless steel pin. All wearing components should be located inside spray head for ease of service. All emergency eye wash and shower equipment should be third-party certified to comply with ANSI Z358.1-2009. DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose. FLOOR BASED PVC EMERGENCY SHOWER CUM EYE-WASH – Corrosion resistant, combination eye wash/shower safety station with ABS plastic shower head, ABS plastic bowl, cast aluminum powder coated flag handle, PVC floor flange, 2” IPS Schedule 80 PVC pipe and fittings, 1” IPS and ½” IPS U.S. made PVC coated brass stay open ball valves, and polished stainless steel pull rod. Unit shall have (2) polypropylene spray heads with integral dust covers, filters, and 1.8-GPM flow control orifices mounted on a PVC coated brass head assembly. Unit shall include ANSI compliant sign as per direction of Engineer in charge.

Supply and installation of lab-sink wall table 1280L x 770D x 900H (mm) R.H. 900 Ht.C-Frame Sliding Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, L.H. 900 Ht.C-Frame Sliding Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, 1200 Module Length Horizontal Members, 770 Depth Wall Side Without Upright End Cover Panel, WFU-SU-2S-750W-635H, Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D), SS Pegboard 550X420X 55, 25 pegs, 3 Way Faucet Bench Mounted 3 Way Water Fittings 8" Swing Gooseneck Model No. : 259924110 01 - 08, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, Silicon Sealant - Black, Masking Tape, 6 MM Self Adhesive Natural Rubber Strip, Acrylic Anti Splash Guard (Size 750mm L X 450mm H X 10mm Thick), Flexible/F Serated Connector Model : Hp 01 Make: Premier, Anti-Siphon Bottle Trap Model : S 04 Make: Premier as per direction of Engineer in charge.

Supply and installation of Spot Extractor with arms mainly for use in chemical environments, where an extended resistance against chemical substances is a demand. All aluminium parts should have a double anodized surface protection. Arm sections – Thin walled anodized aluminium sections with a very good corrosion resistance. Swivel – Swivel with 360 degree rotation. Add reduction for correct connection diameter. Joints – The adjustment knobs on the friction joints should be supported by ball-bearings. The first joint should be supported by a spring (not Ø100-1200). 360 degree rotation where indicated. Mini hood – The Mini hood should be supplied together with the arm and is also interface to the multi-purpose and metal hood. Mounting – The arms can be mounted on ceilings, walls and floors or fixed to tables. By using an extension profile the arm’s operational reach must be increased. Other – All the arms should be provided with dampers, tight down to an under pressure of 3500 Pa. Air temperature -10 ̊C to 70 ̊C. Material recovery: 99% by weight. Components to be provided: Spot Extractor arm, Bracket for Spot Fume Extractor, Multi-purpose hood (380mm x 460mm), Aluminium Extension Profile 1100mm Length, Reducer 75-80 FR Spot Fume as per direction of Engineer in charge.

Supply and installation of Stool: The seat should be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and should be .upholstered with replaceable synthetic leather covers. SEAT SIZE: Diameter 40.0 cm. ADJUSTMENTS: 360° Revolving type. BACK ASSEMBLY: The back foam should be designed with contoured Lumbar support for extra comfort. The upholstery should be available in synthetic leather. BACK SIZE: 45.0 cm (W) covered with polyurethane foam. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be _moulded with density = 45 +1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. HEIGHT ADJUSTMENT: The manual height adjustment should be very easy to operate with a help of a knob. It can be easily locked at the most comfortable position. PEDESTAL ASSEMBLY: The five-prong pedestal should be fabricated from 0.2 ± 0.02 cm :thick HR sheet.( should be :. DD 1079 / HR ), powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal-should be 55.0±0.5cm pitch-circle-diameter- (65.0±-1,0cm-with-castors).-Circular-foot-ring of 052.0±0.2cm made up of 01.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool. TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon as per direction of Engineer in charge.

Supply and installation of Table R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, 1500 Module Length Horizontal Members, 770 Depth Wall Side Without Upright End Cover Panel, 1500 module length back cover panel, WFU-2S-1D-600W-635H, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, Silicon Sealant - Black, Masking Tape, 6 MM Self Adhesive Natural Rubber Strip as per direction of Engineer in charge.

Supply and installation of Lab -Wall Table 6830L x 770D x 900H (mm) L.H. 900 Ht.C-Frame Assy. For Table Depths 620 Wall Side, 1240 Island Without Upright & 770 Wallside With Upright, Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, 750 Module Length Horizontal Members, 1500 Module Length Horizontal Members, L.H. 770 Depth Wall Side With Upright End Cover Panel, Master Upright Without Cutout, Outer Cover For Single-Sided Electrical Trunking, 1500 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module, 1200 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module, WFU-SU-2S-750W-635H, WFU-2S-1D-750W-635H, Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D), 3 Way Faucet Bench Mounted 3 Way Water Fittings 8" Swing Gooseneck Model No. : 259924110 01 - 08, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, Silicon Sealant - Black, Masking Tape, 6 MM Self Adhesive Natural Rubber Strip, Master Upright Extenstion, Flexible/F Serated Connector Model : Hp 01 Make: Premier, Anti-Siphon Bottle Trap Model : S 04 Make: Premier, 6/16A, 6 Pin Shutter Socket - Model No: M1332, 6 Module Plate - Model No: Cs956M-S, 16A, 1 Way Switch Model No: M0130 as per direction of Engineer in charge.

Supply and installation of 5 Feet Benchtop Auto Bi-Pass Fume Hood with Superstructure Frame: It shall be a free-standing rigid panel structure of steel (G.I.). Interior Walls: Double wall ends, not more than 6” wide, shall be provided to maximize interior working area. The area between the double wall ends shall be closed to house the remote-control valves. Cut-outs shall be provided inside the fume hood for service line accessibility. The same to have a cover with a fastener free design. The vertical fascia shall contain the required service controls, electrical switches, and receptacles. Airfoil: A streamlined air foil shall be integral at the bottom of the hood opening on bench and distillation hoods. This foil shall provide a nominal 20mm open space between the foil and the top front edge of the work surface to direct an air stream across the work surface to prevent back flow of air. The sash shall be provided with a separate handle which also provides for air flow when in completely closed position. The foil shall be of 1.2mm steel to resist denting and flexing. Baffles: A stable, non-adjustable baffle with a single slot on the back baffle to aid in distributing the flow of air into and through the hood. The baffle shall be spaced out from the back liner and shall be removable for cleaning. It shall have 3-point suction for low, medium, and high-density fume suction. Duct Collar: A 8”-10” diameter polyethylene funnel shaped rectangular duct collar shall be in the top of the hood plenum chamber. AFM: Fume hoods shall be provided with an alarm system to detect low and high hood face velocities.The alarm system shall indicate the actual face velocity of the hood regardless of sash position. The system shall have an air velocity sensor mounted on the interior side liner of the hood where it is easily accessible for cleaning.The velocity monitor shall have a digital display of the air velocity through the hood face in feet per minute.The alarm signals shall activate any time the face velocity falls below the low velocity alarm set point or rises above the high velocity alarm set point.There shall be both visual and audible alarm signals. The audible alarm shall have a mute. Low and high alarm contacts shall be provided for remote monitoring. LED LIGHT: Two LED Lights of Philips or equivalent make shall be provided in the fume hood. The lighting fixture shall be completely outside the fume hood area. The luminosity on the work surface shall be average 600 Lux. Vertical Sash: A vertical moving sash shall be provided having 5mm toughened clear glass. The bottom of the sash frame shall have a full-length metal handle. The sash track has minimum protrusion to avoid any kind of turbulence. The sash shall be counterbalanced with a weight to prevent tilting and binding during operation. The glass panels shall be 5mm toughened glass mounted in a levelled channel with roller for smooth operation. Flexible Tubing: Utility services like Nitrogen, Compressed Air & Raw water (as per Schedule of Quantity) shall consist of remote-control valves as selected located within the end panels and controlled by in and out facility with flexible hose passing through the side panels of the hood, with colour coded plastic handles. Interior fitting for gases and water shall be with powder coated brass. All gas valves for regular lab gases to have standard needle valve shall be supplied. All supplied valves to clear the following pressure test conditions: Gas Fittings – 7 bar, Water fittings – 10 bars. Electrical Services: The hood superstructure shall be fully wired and shall have a control box with MCB blower starter all safety devices like trip etc. Inlet shall be of 3 phase power supply and the whole electrical shall be of plug and play type. It also has 4 nos. electrical sockets and switches of Northwest make (230V, 5/16 A, 50 Hz). Electric Hatch: There shall be two hatches, one in each vertical front side of the fume hood near worktop level which will allow passage of the electric wires of the equipment being used in the chamber to be guided through and connected to the electric power points. Liner – Interior liner panels shall be 6 mm thick Phenol resin based industrial laminate. Lattice Rod Assemblies: 12mm Dia solid SS rods shall be clamped with the PP clamps to form a lattice arrangement to hold the test samples and rotors within the fume hood. Base Cabinets: Fume hoods are designed to rest on a bench (high base stand, pedestal, or a cabinet) which is a complete rigid steel structure. Storage: Fume hoods are designed to rest on pedestal or a cabinet which is a complete rigid steel structure. Gauge of steel used in its construction shall be 0.8 mm GI for apparatus storages. An FRV mould shall be inserted inside the cabinet wherever acid storages are required (if mentioned in schedule of requirement). Transition: Used to connect fume hood with ducting. They are designed to reduce the static pressure and are made up of Poly-propylene of 6 mm thickness. Start Switch button: Fumehood shall have Start Switch button, in the event of main power failure, when the power comes back, the Fumehood electrical supply should not turn ON unless START switch is pressed. Granite: Standard hood work surface shall be 18mm thick jet-black granite in the form of a watertight pan, not less than 7 mm deep to contain spillage. Worktop will have oval shaped 102 mm X 175 mm ‘PP’ Cup-Sink for drainage. Top shall be manufactured at the same manufacturing location as the fume hood to assure proper cut-out alignment and coordinated shipping. The work surface and cup drain shall be available in black. Centrifugal Blower: Silent high efficiency remote blower consisting of continuous rating motor and chemical resistant impeller. The blower shall be designed to give a face velocity at safe working height as per the international safe velocity norms. (ANSI/AIHA Z9.5). The blower body shall be polypropylene UV treated high density and chemical (corrosion) resistant and mounted on a metallic stand. Ducting: Rigid Ducting of PP (Polypropylene) + FRP (Fibre Reinforced Polyester) and flexible ducting with flanges, bends, damper transitions, clamps etc. Flexible joint shall be provided in the ducting to avoid transmitting the blower vibrations to the hood. A weatherproof rain cowl is provided at the outlet of blower as per direction of Engineer in charge.

Supply and installation of direct driven PP FRP Centrifugal Blower of 4500cfm @ 100mm WG Static pressure including suitable clamp adapter, Electro galvanized stand and fasteners like bolts, nuts and washers , base frame, vibration isolators, TEFC motor,Motor 7.5HP/4P PI 55 CG/BB/Kirloskar/HEM, with accessories, Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps. 12” (300mm) 100% Injection Molded PP Damper with Two Side Flange. Vertical single stage packed bed scrubber with integrated water tank. The scrubber capacity is 4500 CFM and made up of PP+FRP material. The approximate size shall be 1100 mm dia & 4100mm ht, complete with packing material,. mist eliminator, inspection window, and Epoxy coated MS ladder with handrail. Provision for Makeup Water connection with control Valve, Water Level Indicator, provision for Drain connection with Control Valve, Over Flow Pipe with float valve. Scrubber Recirculation Pump with inlet Flange with Y-Strainer, ball valves, Outlet Flange with NRV, Ball Valve. Complete recirculation piping with suitable supports. Inlet and outlet flange for duct connections with gasket and Bolt Nuts. Vertical Seal less Scrubber Pump with enclosure suitable for 185 Lpm flow, 2HP , 3phase 50Hz, 415Volts. Provision for Dosing connection if any with Valve, Scrubber Mounting Bolt & Nuts with Anti Vibration Pads. The operating Temperature is upto 60deg C (max.) and Pressure drop across the scrubber shall not be more than 600Pa (approx.) Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating. Inlet/Outlet Dia: 250mm, Impeller Dia: 315mm, Non-FLP Motor: 1 HP 1400 RPM, CFM: 300 @ 50 WCMM Static Pressure. Motor make : IE2 (Non FLP), Crompton Greaves/Bharat Bijlee make whichever is available. Motor Description: IP55, 3 Phase, 440 Volt , 50 Hz. Weather cover for motor Anti-Vibration Pads & M10x100 pin type Anchor Fasteners. Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps. 10” (250mm) 100% Injection Molded PP Damper with Two Side Flange. Design, supply & Installation of PP-FRP ducting of wall thickness 3mm PPGL + 3mm FRP for sizes up to 500mm Dia. for 100 Running Ft. (Approx.), Above 501mm Dia 4mm PPGL + 4 mm FRP shall be used unless otherwise specified. Including clamps, hanging support, all hardwares required to complete ducting work. Ducting upto 500mm Dia - wall thickness shall be 3 mm for PP and FRP. PP and FRP Understorage Ducting as per direction of Engineer in charge.

Supply and installation of Storage Cabinet for storages of corrosive chemicals and is provided with a ventilation system to enable exhaust of localized fumes emanating from the chemicals stored. The material should be is 1.2 mm CRCA MS with pure Epoxy Powder coating. It must be fitted with a float glass to enable visibility inside the cabinet. It should also has louvers/perforations for air supply. MS Apparatus Storage Cabinet [with top cover plate] 900W X 560D X 1800H. PP DAMPER DIA. 230 X 150 L : 6.0 mm thk as per direction of Engineer in charge.

Supply and installation of Island Table 3830L x 1500W x 900H (mm) with Single Side Sink, R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, R.H. 900 Ht.C-Frame Assy. For Table Depth 1540 Island With Upright, L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, L.H. 900 Ht.C-Frame Assy. For Table Depth 1540 Island With Upright, Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, 750 Module Length Sliding Horizontal Members, 1500 Module Length Horizontal Members, 1540 Depth Island With Upright & Without Upright End Cover Panel Master Upright With L.H.Side Cutout, Island Without Upright C-Frame Joining Bracket, Fixed Type Reagent Shelf (Main Type) 1500 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only), Fixed Type Reagent Shelf (Main Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only), WFU-2S-1D-750W-635H, PP Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D), 3 Way Faucet Bench Mounted 3 Way Water Fittings 8" Swing Gooseneck Model No. : 259924110 01 - 08, Double Valve,Turret,1-Hole,Fix.Nozzle, Press-LPG Model no:25321091012-14, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, Silicon Sealant - Black, Masking Tape, 6 MM Self Adhesive Natural Rubber Strip, Master Upright Extenstion, Flexible/F Serated Connector Model : Hp 01 Make: Premier, Anti-Siphon Bottle Trap Model : S 04 Make: Premier, 6/16A, 6 Pin Shutter Socket - Model No: M1332, 6 Module Plate - Model No: Cs956M-S, 16A, 1 Way Switch Model No: M0130 as per direction of Engineer in charge.

Supply and installation of Island Table 3830L x 1500W x 900H (mm) with both side sink R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, R.H. 900 Ht.C-Frame Assy. For Table Depth 1540 Island With Upright, L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, L.H. 900 Ht.C-Frame Assy. For Table Depth 1540 Island With Upright, Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright, 750 Module Length Sliding Horizontal Members, 1500 Module Length Horizontal Members, 1540 Depth Island With Upright & Without Upright End Cover Panel, Master Upright With L.H.Side Cutout, Island Without Upright C-Frame Joining Bracket, Fixed Type Reagent Shelf (Main Type) 1500 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only), Fixed Type Reagent Shelf (Main Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only), WFU-SU-2S-750W-635H, WFU-2S-1D-750W-635H, Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D), 3 Way Faucet Bench Mounted 3 Way Water Fittings 8" Swing Gooseneck Model No. : 259924110 01 - 08, Double Valve,Turret,1-Hole,Fix.Nozzle, Press-LPG Model no:25321091012-14, Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk, Silicon Sealant - Black, Masking Tape, 6 MM Self Adhesive Natural Rubber Strip, Master Upright Extenstion, Flexible/F Serated Connector Model : Hp 01 Make: Premier Anti-Siphon Bottle Trap Model : S 04 Make: Premier, 6/16A, 6 Pin Shutter Socket - Model No: M1332, 6 Module Plate - Model No: Cs956M-S, 16A, 1 Way Switch Model No: M0130 as per direction of Engineer in charge.

Supply and installation of Glassdoor storage with an overall size of 916mm(W) x 486mm(D) x 1980mm(H) with welded construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The glassdoor storage shall have a brass handle and a 2 way locking mechanism with shooting bolt . It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available as per direction of Engineer in charge.

Supply & Installation of Movable Storage Unit on Rail of the following dimension. Overall Dimensions of SS1 - Single Static 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2083mm(H). SL1 - Single last 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2106mm(H). TM1 - Twin Mobile 1 Bay Push Pull Type(U/C + Fittings + Handle) shall be 915mm(W)x762mm(D)x2180mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns.Shelf construction made of 0.7 thk CRCA steel conforming to IS: 513 Gr.D or DD.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. y. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimension of Rail:2400W X 124D X 31H mm. It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the help of raul plug & screw, ensure the ground is level.

Supply and installation of Modular Workstation of 1500W x 600D with KBPT, CPU Trolley & Pedestal: Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric tile. Bottom tiles - Plain metal. SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric tackable along with split white board. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d. Pedestals with legs - pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors. KBPT with mousetray - metal. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring as per direction of Engineer in charge.

Supply & installation of APO Tracing Table for drawing purpose. The Work Surface will made of 36mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Full length access panel is provided with soft closing hinges inline with worktop edge. Understructure- The understructure consist of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Wire Management will be done by an array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout is provided for electrical fittings below access flap per seat as per the direction of Engineer-in-charge.

Supply and installation of High Back chair with Adjustable Armrests: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Back Size is 45.5 cm. (/1/) x 53.0 cm. (H) Seat Size is 48.5 cm. (W) x 49.0 cm. (D). The HR polyurethane foam used in seat and back cushion is moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression.The seat and back are firmly connected to the base frame and should give multi-dimensional movement .The "S" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which should be inbuilt in seat base and the tension (return force) should be user weight dependent.The armrest assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide: The height adjustment feature should be button operated having adjustment of 6.6±0.5cm. The Armrest Top should be made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm. The pedestal should be injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors.The pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. 5 nos. twin wheel castos are injection moulded in Poly-amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal as per direction of Engineer in charge.

SITC Of 75 Inch UHD Display, Panel Screen Size/ Aspect Ratio 75 INCH / 16:9,Panel Type/Backlight Type IPS Panel/Direct LED Brightness 500 cd/m²,Native Resolution 3840 x 2160 (16:9) - UHD, Operation Hours ,24/7, HDMI Input 4 x HDMI,USB Input 4 x USB (2 x 2.0, 1 x 2.0 internal, 1 x Type C),DP Input DP 1.2a x 1,DP Output DP 1.2a x 1,VGA Input 1 x 15pin D sub, Video Output DP 1.2a,Audio Input Line In L/R, Audio Output M3 Jack, Optic SPDIF, External Control 1 RS232(DE-9F), External Control 2 Ethernet(RJ45),External IR Sensor RJ12.Internal Speaker 10 W x 2.RS232C control Yes, LAN control Yes. RAM 2 GB, Internal Storage 16 GB, Android 9.Approved Make: Panasonic / NEC/LG. Trolley For Display- Approved Make: NT/Lumi. Connectivity Face Plate. HDMI Cable 25 Ft- Approved Make: Kramer/Extron/Crestron. All in one collaboration bar: MS- Teams and Zoom Certified All-in-One Video Collaboration Bar.Chipset Qualcomm Snapdragon 845 chipset.Camera 20MP, 10X Hybird zoom Camera.AI Features Auto Framming, Speaker Traking.Type of sensor CMOS.Camera Control (focusing, brightness, and white balance) Automatic. Digital zoom 3X Digital.Optical zoom 3.5X Optical.Dual Camera System YES.Wide Camera 8MP Camera, Resolution: 4k, 1080p and 720p at 30fps, Field of view: 120°,4x e-PTZ Camera.Conference security protection Electric camera lens cap, automatically protect non-video meeting.Telephoto Camera: 8MP Camera, Resolution: 4k, 1080p and 720p at 30fps, Field of view: 90°, 10x Hybrid Zoom (3.5x optical, 3x digital), Horizontal Rotation Angle: +25°/-25°, Vertically Rotation Angle: +16°/-16°.Video Standard and Network Suitability Video codecs: H.264 High profile, H.264 SVC, H.264.Microphone Build-in-Microphone 8 MEMS.Wired and Wireless Content sharing .Should be support additional wired and wireless Microphone of the same OEM,Number of Ethernet connection points for System supports for RJ-45, 10/100/1000 : 1, Video Codec shall support 16:9 format,Number of Input USB Ports 2, Number of Output HDMI or equivalent Port 2, TCP/IP IPv4 & IPv6.Touch Console : 8-inch touch screen.Approved Make: Yealink/ CISCO/Lumens. Wireless Microphone.Optimal HD Voice, Full-Duplex technology,20-feet (6-meter) 360° voice pickup, Capacitive mute touchpad, WiFi Technology (WPA2/AES128 Encryption), Expansion Mic (Works with built-in mic).Approved Make: Yealink/ CISCO/Lumens. Wireless BYOD and Content Sharing Dongle.Decoder Up to 4k/30fps.Input Power 5V/600 mA.Interface Full-featured USB Type-C×1 USB-C to USB-A Adapter x1.Wi-Fi Standard Wi-Fi 6, 802.11 a/b/g/n/ac/ax.W-Fi Frequency 2.4 GHz/5 GHz.Bluetooth 5.0.Approved Make: Yealink/ CISCO/Lumens. Network Switch-Approved Make: D-Link/Linksys/CISCO. Connector Cable, Cat 6 Cable of Approved Make: D-Link/ Extron/CISCO. Control Cable.Approved Make: Belden / Klotz / Extron as per direction of Engineer in charge.

Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk on spine, 23 MM FIN IN SAHRED CONDITION AND ASILE ONDITION Ht - 1200 including powder coated aluminium trims. Tiles: top tiles WHITE BOARD . Bottom tiles - Plain metal. Top tile for 23 mm fin - FABRIC TACKABLE. INTERMEDIATE BLOCKS Intermediate blocks are given in DL+DL finsh. Legs - metal powder coated legs at the end and shared condition. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 W X 600 D. CPU trolley - with castors. KBPT with mousetray - metal. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring.

Supply & Installation of APO Electrical lab table of size 1200W-750D-750H mm of following specifications: for each module: Table top is made of 19mm thick commercial plywood finished with 1mm laminate on top and edges finished with 2mm PVC edge banding on teakwood understructure with legs section 50mm x 50mm with cross member section of 50mmX25mm. Panel to be finished with 1mm laminate on front. Teakwood structure and legs to be finished in melamine polish. All inside/back ply surfaces to be treated with french polish. the table should be mounted with 10mm think laminating board with circuit inscripted as per departmental requirement. Size of Mounted Board is 1200 mm W X 600mm H