University Of Jammu Tender

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A,30KA,FPMCCB

Supplying and fixing of MCCB MS Enclosure suitable for MCCB's 100A FP to 160AFP

Supply, Installation, Testing and Commissioning of 20 KVA servo stabilizer Digital Microcontroller Servo Voltage Stabilizer out-door type with fresh dehydrated oil. With protection, complete in all respects. Technical Specifications of 3 Phase Servo Stabilizer: Capacity : 20 KVA, Type : Un-Balanced 4 wire system( with Buck- Boost Transformer) Method of Cooling : Oil Cooled, Phase : 3 Phase, 4 wire, Frequency : 50 Hz Input Voltage : (P-P) 210-460 (P-P), Output Voltage : 415 V +-1%, Efficiency : 98% at full load Operation Temperature : 45 Degree Celsius above ambient Relative Humidity : Up to 90%, Correction Speed : Up to 35 V/sec No load current : Less than 1.5% of rated current BBT : CRGO core material 0.23mm thickness Metering : LCD , Analogue or Digital ( as per requirement), Indication : Indicators for phase failure, over-load and over-voltage Controls : Auto/Manual Selector Switch, Increase Decrease Toggle Switch for Manual Operation, Output Switch Protection : Input High and low cut off, Output High and low cut off, Overload, Short-circuit protection, Time Delay Protection, Class of Insulation : “A”, Fabrication Box Paint : 7 Process Powder Coated System construction : As per IS 9815, Out put MCB 4P 10KA 40A for out put termination Independent Phase Control : Maintain each phase voltage stable irrespective of unbalanced load Transformer Winding : Copper 99.9% Pure, Duty Cycle : 100%, Container: 14 SWG with Stove enamelled paint, Cable Box and Busses : BAR leads suitable size of cable box with 6 aluminium busbars (3 for input, 3 for output and 1 for neutral), Regulator : Toroidal Type, Oil capacity : As required Paint : Powder Coated, Color : RAL 7035 (Polyester Powder Coating) System Construction : AS per IS-9815

Foundation Construction of Foundation for 20 KVA servo and contoller (as required at site) of 2.5 feet above ground and 2 feet below ground level, size (4 feet x 5 feet ). Excavating/ steel bars/ Reinforced cement concrete work in well-staining, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse Sand (zone-III): 3 graded stone aggregate 20 mm nominal size). along with GI Sheet roofing with proper MS supports to cover the area As required as per site, complete in all respects.

Supply, Installation, Testing and Commissioning of Star/delta 10 HP capacity Automatic Star Delta Submersible pump controller, with single phase preventor, star delta timer, OLR, SSP with automatic switch, combined V/A meter, selector switch, ON OFF system and indications, IP 54, IS/IEC60947-4-1, of reputed make

Wiring with the following sizes of FR PVC insulated copper conductor, 3 core submersible applicaion cable in HDPE conduit as required 3C x 6 sq.mm

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Note. The quoted percentage (%age) should preferably be in fractional form in order to minimize concurrence of similar quoted rates