Small Scale Industries Development Corporation Limited Tender

M.S. Grill of required pattern as per design Square Bar Type

Angle iron fencing posts and flat strips mademof standard angle sections, cut and bend at bottom with holes drilled and top bent, duly red oxide painted (For fencing purposes)

Flat iron strips made of standard sections duly cut and holes drilled, complete with red oxide paint. (For fencing purposes)

Rolling Shutter made from HR/BP Sheet 22g

Fitting, fixing

SIGN BOARDS Supply of sign boards made out of ISA 50x50x6mm legs and frame with M.S. Flat 40x5mm on CR Sheet 22 guage duly welded and fitted with nuts bolts wherever required incl. cost of painting and letter writing as per sizeof department. (as per requirement)

SIGN BOARDS Supply of sign boards made out of ISA 50x50x6mm legs and frame with M.S. Flat 40x5mm on CR Sheet 22 guage duly welded and fitted with nuts bolts wherever required without painting and writing as per sizeof department. (as per requirement)

Steel sign boards made out of 2" dia MS Pipe frame over legs with 16g CR Sheets fitted with M.S. Flat clips 40x5mm with pipe frame and MS plate 4"x4" at the bottom of the legs duly painted and lettering complete.

Steel sign boards made out of 2" dia MS Pipe frame over legs with 16g CR Sheets fitted with M.S. Flat clips 40x5mm with pipe frame and MS plate 4"x4" at the bottom of the legs without painting and writing

IRON NOTICE BOARD SIZE 6’X3’ Iron Notice Board size 6’x3’ frame made of angle Iron 50x50x6mm fixed with MS Sheet 0.80mm, front Side covered with doors of iron jail, with locking facility Board having legs of angle iron.

IRON NOTICE BOARD SIZE 4’X2.5’ Iron Notice Board size 4’x2.5’ frame made of anglre Iron 32x32x5mm fixed with MS sheet 0.80mm, front Side covered with doors of angle jail, with locking facility Board having provision to be mounted on wall

IRON GATES Iron Gate of double leaf made out of ISA 50x50x6mm frame and supports of M.S.Flat 40x5mm fitted on joints of CR Sheet cover 1.6mm incl. hold fasts and locking arrangement and vichetgate duly welded and painted with red oxide paint

IRON GATES Iron Gate of double leaf made out of ISA 50x50x6mm frame and supports of M.S.Flat 40x5mm fitted on joints of CR Sheet cover 1.6mm incl. hold fasts and locking arrangement and vichetgate duly welded and painted with red oxide paint Fancy type using fancy pipe, sq.bar and gate channel

IRON GATES Iron Gate of double leaf made out of ISA 50x50x6mm frame and supports of M.S.Flat 40x5mm fitted on joints of CR Sheet cover 1.6mm incl. hold fasts and locking arrangement and vichetgate duly welded and painted with red oxide paint Plane type using angle iron amd MS Sheet of 1.6mm

IRON GATES Iron Gate of double leaf made out of ISA 50x50x6mm frame and supports of M.S.Flat 40x5mm fitted on joints of CR Sheet cover 1.6mm incl. hold fasts and locking arrangement and vichetgate duly welded and painted with red oxide paint Using MS Pipe 40mm dia and wire mesh

Iron Sagri medium size made of 0.63mm CR Sheet

Waste paper basket standard size made out of CR Sheet 0.63mm with reducing base duly painted

Collapsible Shutters Collapsible steel shutters with vertical Channels 20x10x2mm and braced with Flat Iron diagonals 20x5mm size with top & bottom rail T-Iron 40x40x6mm with 40mm dia, Steel Pulley complete with Bolts Nut locking arrangement, stoppers, handles including applying a priming coat of app. Steel primer.

Collapsible Shutters Fixation charges per shutter

Guide Frame Angle Iron 40x40x6mm with 50” long 1.25” dia GI Pipe B-Class and Angle Iron 1”x1”x1 suter attached with the GI Pipe to the length of 1’ with slotting alongwith Nut Bolts complete job (As per drawing).

Gas Holder Frame work with 12mm Square bar with 79” long 2” dia GI Pipe fitted with the plates at bottom & top of size 6”x6”x6mm and fabricated with14 guage sheet round and 16 guage sheet at the top fitted with ¾” GI Socket and 4 Nos. of handle complete job (As per drawing).

PASENGER SHED Sainless Steel Pessenger Shed Made of 304 pure quality Steel of Size 8’x20’ which includes 6’’ dia Pipe for pillar 4Nos. of 10’Trusses/purlins, vertical section made of stainless steel pipe of 1.5’’x1.5’’, 9 Nos. & 3’’x1.5’’ pipe 1 No. of 20’, base plate 12’’x12’’, top plate 8’’x8’’ stainless steel & Iron base plate 6mm thick with a complete roofing Made of sinusoidal color coated sheet of standard thickness 2.0mm with Sitting arrangement with two No. chrome coated full length chairs (3 seater)

SKYLIGHT DOME: Skylight Dome (polycarbonate sheet dome) made of MS hollow pipe Section painted with enamel paint, anchored to the base concrete with Necessary base plates with fastener, aluminium profile with EPDM Gasket in between for fixing 10mm multiwall polycarbonate sheet (UV Coated) fixed in position, incl, erection

COCOON TRAY Cocoon Tray size 124x91cm having depth 7.5cm, base wire mesh 1.6cm Sq. sides with CGI sheet with partition in the middle of CGI Sheet. Tray Mounted on Angle Iron frame of angle iron 2.5cm, 4 legs of 2.5cm of Having height 21cms. Each leg with top collar of same thickness (3cm) Angle welded giving one cm. space for stacking of trays one above the Other. Total weight of Tray 11.500 kgs (+5%) To be supplied as per Sample

Garbage Container Blue /Yellow or as per requirement 4.5 Cubic Mtr. Made out of Plate/HR Sheet 5mm, 3mm & 2.5mm and CR Sheet1.6mm, Channel 75x40mm, Angle Iron 40x4x0x5mm; Bottom 5mm HR Sheet/Plate, Side 3mm, Top cover tall gate 2.5mm HR Sheet, Window 1.6mm CR Sheet Bottom & Side structure; Channel 75x40mm, Angle Iron 40x40x5mm Leading windows 4 No’s

Fabrication of R.C. bins: including painting and letter writing complete job for capacity 1m M.S Plate at sides 3mm, bottom 4mm, MS Angle at top frame 50x50x6mm, side handle 2 nos 25mm MS round, Bse 48”x30”, Top 60”x42”, Height of bin 36”, Bottom Support of MS Angle 65x6mm, Painting Body Blue / Green, Interior Anti Rust Coating

Handlomm Weaving Machine (Loom) made of pipe 3”x11/2”,2”x1” sq, 1” round, 3/4 “round, 1 1/2 “ round rings, pullers, sheet box etc fitted with nut-bolts with paint work

Passenger Shed / Vatika (Gazebo type) Made out of M.S steel pipes 6” dia fitted with gusset plates, angle iron 40x40x6mm and also provide 0.5mm profile sheet roofing with J/2 hook bolts and also provide cast iron heavy duty ornamental grills on bottom & top with hollow SW pipe railing to bottom end.(as per department requirement)

Seed Bins made of size 17’ length & 17’ height having a Storage capacity of 50 kgs of rice made out of GP Sheets 0.5 MM thickness including cost of Hings, Lock, Kundi, Handless, Revets etc complete job

Item: Steel Complaint Boxes Size: 18”x15”x8” (LxBxH) Sheet: GP Sheet 22 Guage Hings: 02 Nos. (3”) Lock: Link or Godrej Make Paint: Blue Enamel Paint with writing

Item: Steel Complaint Boxes Size: 18”x15”x8” (LxBxH) Sheet: CR Sheet 22 Guage Hings: 02 Nos. (3”) Lock: Link or Godrej Make Paint: Blue Enamel Paint with writing

Mobile Toilet Van Specification for Toilet Van • Length of the toilet van excluding hook 7 feet 6 inches. • Breadth of the toilet van including the walk way on both sides-6 feet 10 inches. • Height from ground-10 feet. • Cubical height - 6 feet. • Cubical width – 3 feet. • Cubical breadth- 3 feet. • Number of W.c of stain less steel Railway Type- 04 No’s for four seater toilet Van. • Night soil tank of 3mm M.s sheet painted with Anti corrosive paint-700 ltrs capacity. • Heavy Duty MS water tank with two taps mounted on the chassis-500 lts capacity. • Door of each compartment made of MS frame fixed with 3mm aluminum composite panel and the partitions of the same material. • The walk way of M.S. angle iron 40x5mm with flat iron supports 1”x6mm provided with hinges fitted with chequered M.S. sheet 3mm thick on top. • Railing of M.S. pipe 40mm and M.S. pipe 25mm dia. • There shall be ladder fitted on the both sides of the van. • One outlet valve 21/2” pipe for foul smell. • Roof shall be made of 24 SWG FRP sheet or Polycarbonate sheet 3mm to be bolted at the top. • Flooring of each cubical shall be chequered Aluminum sheet. • 100mm out let valve for drainage. • There shall be 2 wash basins with at the back of the van with proper disposal. • There shall be two mirrors at the back of the van. • There shall be 2 no’s handle, 1 clothes hook, 2 no’s locking bolts in each cubical. • The whole toilet van shall be painted with green and blue color or any other colour combination from outside as per the design with will be given by the Department. • 100mm dia 20 feet long steel wire reinforced synthetic rubber pipe for disposal of waste. • The chassis shall be movable on a chassis fitted with the tyres, tubes and Rims. • Heavy duty toeing hook shall be provided in front of the van.

Iron Fencing of size 9’x6’ frame made of Angle Iron 40x40x5mm and 32x32x5mm fitted with GI Chain Link Mesh of size 50x50mm. Mesh strengthened with Flat Iron 40x5mm and 32x5mm fixed with 2mm dia wire. Total height of frame shall be 7 ½’ including 6’ height of frame and 1 1/2 ‘ angle iron for plenth

Screen House Size 96-240 SQM Structure:- It consists of Galvanized Tubular structure having GI Pipe medium grade, Foundation 48mm OD, Column 60mm OD, Arch 48mm OD, Bottom/ Horizontal Beam 33mm OD, Bracing 33mm OD, Purlins 42mm OD and 33mm OD, Clamps, Nut Bolts, Accessories, Door (1mx2m) Covering Material:- Stainless steel jaali of 40mesh fixed with aluminium strips. Locking Profiles:- It consists of Aluminium flat strip to fix the ss jaali. Shade Net:- It consists of UV Stabilized Shade Net 50 % Screen house with nylon support cables, side support with clamps with manual collapsible arrangement. Drip Irrigation System- It consist of HDPE/PVC pipe of 6kg/cm2 pressure as main and submain, Inline Lateral, Screen filter, PVC Ball Valves, Fittings and Accessories Foggers System- It consists of Four way anti-leak foggers with 28lph discharge at 2.5m X 2.5m Spacing, HDPE /PVC pipes of 6 Kg/cm2 pressure,PVC ball valves, LLDPE laterals, fitting and accessories. Mono Block Pump with starter, water storage tank 1000 liter along with fittings and accessories Civil work for the foundation of Screen House and construction of bricks wall in cm 1:4 0.23m thick, .30m height above the ground and .30m below the ground along the sides of screen house duly plastered on both sides with ratio 1:6. Installation, Transportation and commissioning of Screen house

Screen House Size 480-1008 SQM Structure:- It consists of Galvanized Tubular structure having GI Pipe medium grade, Foundation 48mm OD, Column 60mm OD, Arch 48mm OD, Bottom/ Horizontal Beam 33mm OD, Bracing 33mm OD, Purlins 42mm OD and 33mm OD, Clamps, Nut Bolts, Accessories, Door (1mx2m) Covering Material:- Stainless steel jaali of 40mesh fixed with aluminium strips. Locking Profiles:- It consists of Aluminium flat strip to fix the ss jaali. Shade Net:- It consists of UV Stabilized Shade Net 50 % Screen house with nylon support cables, side support with clamps with manual collapsible arrangement. Drip Irrigation System- It consist of HDPE/PVC pipe of 6kg/cm2 pressure as main and submain, Inline Lateral, Screen filter, PVC Ball Valves, Fittings and Accessories Foggers System- It consists of Four way anti-leak foggers with 28lph discharge at 2.5m X 2.5m Spacing, HDPE /PVC pipes of 6 Kg/cm2 pressure,PVC ball valves, LLDPE laterals, fitting and accessories. Mono Block Pump with starter, water storage tank 1000 liter along with fittings and accessories Civil work for the foundation of Screen House and construction of bricks wall in cm 1:4 0.23m thick, .30m height above the ground and .30m below the ground along the sides of screen house duly plastered on both sides with ratio 1:6. Installation, Transportation and commissioning of Screen house

Repairing of existing Hi Tech Green House alongwith construction of benches and portrays Exhaust Fan 50” 1 No. Cooling pad system with frame 1 SQM Benches 3Mx1M (3/4”x2MM) 1 SQM Pro Tray with 98/99 Cavity 1 No. Aluminium Tee (60MMx30MM) 1 No. Drip and fogger system 1 SQM Monoblock Pump 2HP and Filter with fitting and accessories 1 No. UV sheets 200 microns 1 SQM Insect net 40 mesh 1 SQM Shade net 50% 1 SQM Water tank 1000 liter 1 No. Panel for Exhaust fan 1 No. Panel suitable for 2Hp pump 1 No. Stainless steel jaali 40 mesh 1 SQM Bricks work duly plaster both side 1 SQM

Ballot Box Metal 1. Size: Height=470 mm Length=335 mm Width =280 mm Slit Size : Length=95 mm Width =10 mm 2. Sheet:- SAIL/TATA Manufacture CR Sheet/Coll. 3. Bottom and side walls of the ballot box: 1.00 mm 4. Upper Lid/Covering Lever/Handle/ Bracket of size : 1.60 mm 5. Locking plate/Locking lever : 2.0 mm 6. Ballot Paper inserting slot (in upper lid) of size: 95x10 mm 7. Slit for Paper Seal: 0.63 mm 8. Thickness of frame : 0.63mm 9. Tolerance Admissible : + 5% As per IS Standard 10. Primer : Single Coat 11. Painting Double Coat: Olive Green 12. Primer/Paint make : Nerolac/Berger/Asian/ Shalimar The serial number of ballot box will have to be embossed on the outside of the Ballot box. Like JK20 _ _ _ 1

Iron fencing size 8’x6’ height of frame 9’. Frame consists of angle iron picket 9’ long of size 50x50x6mm (including 6” slit), picket shall be requiring 4 nos of 12mm dia holes at equal distance in between from top to below 6’ length, flat iron of 40x6mm to be fixed with picket of length 6’ with same nos of holes. Another angle iron 8’ length of size 50x50x6mm to be fixed horizontally to tie two vertical pickets, it shall be requiring 5 nos of 12mm dia holes at equal distance, flat iron 8’ long of size 40x6mm to be fixed with angle with same nos of holes. Nut bolt 10mm dia 50mm long to be provided as per requirement all material shall be painted a coat of red oxide primer. The material shall be marked with the "logo" of the firm

Angle Iron Rack Providing and Fixing of Iron Racks made of angle iron 40x40x6 mm and Flat Iron 40x6 mm for keeping answer sheets

Angle Iron Frame Welded Mesh (1”x1” square inch) Iron Fencing frame made of Angle Iron 40x40x6mm fitted with Welded Mesh (1”x1” square inch). Mesh strengthened with Flat Iron 20x6mm fixed

Construction of Car / Scooter Parking for staff & student Student parking shed, parking shelter made out of tubular trusses made out of rectangular hollow section 96mmx48mmx3.2mm structural steel confirming to is:4923 with a spacing supported on columns of MS steel 3”dia round pipe fitted with gusset plates. The struts shall be made of 66mmx33mmx2.9mm rectangular hollow section with providing color coated sheet on top fitted with GI nuts and bolts. All structure be pre coated with primer and enamel painted in black color.

Specification of Hitech Green House with Polycarbonated Sheet, Fan and Pad system. Area: 500 Sqm Galvanized structure of square pipe with 1.8-2mm thickness Length: 25m, Width: 20m(span 8m - 2 Nos and Hockey 2m - 2 Nos), Side Height:3m, Centre Height: 4.2m Column 65mmx 65mm thick GI Pipe ISI mark Trusses Bottom: 32mm x 32mm, Members: 48mm x 48mm, Bracing: 25mm x 25mm GI Pipe ISI mark Foundation 48mm x 48mm GI Pipe ISI mark Purlins 32mm x 32mm GI Pipe ISI mark Hockey 38mm x 38mm GI Pipe ISI mark Shade Net 50% UV stabilized Agro shade net, Green colour Ante Room Double Door Room- of size 2.1m x 2.1m x 2.43m (LxWxH) covered with 6mm thick polycarbonate sheet Cladding of roof, front wall, end wall, & sidewalls of Green house will be with 6mm thick clear multi wall polycarbonate sheet with Aluminium Strip. Cooling System Fan and Pad system - cooling pad complete with all necessary framing material, required supporting, distribution & returning piping. Size of cooling Pad 16m x 1.5m x 4" thick. Exhaust Fan of 50" size with 1.5HP motor- 4 Nos Heat convertors 2.5kw - 2 nos. Panel including Temperature & Humidity Control System having Timer, Temperature Control System, Relative Humidity Control System, Provision for sprinkler and Fogging System motors, etc. Door Size: 2m x 1m of GI pipe - 2 nos. Fooging System It consists of four way anti leak foggers with 28 lph discharge, PVC/HDPE pipes of 6 kg/cm sq. pressure rating of various sizes, with fittings flush valves,filter, water tank 1000 ltrs capacity, MBP 1 HP Drip/Sprinkler system Drip/Sprinkler irrigation system Hanging type with 70 lph discharge PVC/HDPE pipes of 6 kg/cm sq. pressure rating of various sizes with fitting, flush valves, Filter, etc, water tank 1000 ltrs capacity, MBP-1 HP Foundation/Civil Work Concrete foundation 30cm x 30cm x 75cm for main column and corridor, Brick work 1 ft below ground level & 1 ft on all sides above ground level duly plaster on both sides.

Hi-tech Polyhouse with Fan & Pad System covered with UV sheet Single span(Size 500sqm) Size-500 sqm (includes side corridors) Length: 36 m, Width: 14m(2+10+2) Side Height- 3 Mtr Centre Height 4.5 Mtr Bay Width 8 x 4 Mtr No of Span- 01 GI pipe structure of BIS standards All Structure, Rafters, Purlins, Trusses are of GI pipe and as per ISI 1239/3601 standard. All pipes are of ISI standard with 1.8-2mm thickness. Foundation Pipe: 60mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe 76m OD x 2mm thickness GI Pipe. Bottom: 60mm OD x 2mm thickness GI Pipe. Arch Pipe: 42mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm ODx2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI Pipe Curtain Pipe: 20mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Poly lock profile will be made up of GI section fixed witth zig zag spring of GI material. Cladding Material High quality UV stabilized 5 layered, 200 micron thick with drip lock (anti drip) diffused, anti-dust, anti-condensed .Shade Net 50% UV stabilized provided inside the structure with manually folding spreading system, GI wire will be used to fix shade net with sliding arrangement for opening & closing as per requirement. Pulleys assembly with nuts & bolts will be provided Curtain Rings & curtain clamps with respect to standard specification will be provided. Side ventilation of insect net of 40 mesh, rolling curtains on two sides with manual rollup system Entrance Room & Door One Ante room of size 2m x 2m x 3m (LXWXH) will be provided and covered with UV stablizes 200-micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System Four way foggers fixed on 16mm laterals are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution with Grid 3mtr x 3mtr, Fogger discharge range:- 28 LPH with Monoblock pump 1.5HP Drip Irrigation 1. Network Pipes: Main:HDPE/PVC Pipe: 60mm 6kg as per as per IS: 4985:2000 S/M: HDPE/PVC Pipes: 50mm 6Kg used as laterial for drip irrigation 2. Fitting & Accessories: Heavy duty HDPE/PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3. Inline tube: Drip inline 16mm among each row with 2 LPH normal flow rate OR Sprinklers at the top. 4. LDPE Lateral Pipe: Misting line with 16mm 5. Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6. Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7. Filtration system: Screen Filter 12m3/hr 8. Air Release Valve: Long lasting and safe operation of system. Evaporatiing cooling system (ECS) for cooling system ECS Costruction Material:- ECO Friendly Aluminium Section: Tray side, Top etc . Cooling Media: (8m x 1.5m x 100mm) x 2 Nos thick cellulose pad Miscellaneous: Fasteners, Galvanized, Rivet-Aluminium PVC Pipe: 20mm/25mm/32mm with elbow & Tee for over flow & drain pipe Water Tank: PVC Tank 1000 Liters. Monoblock Pumpset: 1HP Exhaust 50" with 1.5 hp motor six blades - 2 Nos Automatic control system: Control Panel for Temperature, Humidity and Light will be fixed in Buffer Area. Relative Humidity + temperature controller Programmable, Cyclic timer, main switch (Rotary) Individual indicator with a main ON/OFF switch, Light indicator for main light, heating, cooling & humidity Plant Work Station/ Benches Benches consist of GI round pipes 20mm x 2mm thick. Nut bolts Bench top width will be 0.9m Length 50 RM Seedling trays having 99 cavities (250 nos) Standard illumination system: Two number LED 100-watt flood light will be provided in the poly house Brick work/ civil work Foundation base block height 2.5' x 9" x 9" each in CC 1:2:4, wall for Hi-Tech green house 1' below earth surface, 2.5' above earth surface 9" wide exposed surface plastered with cement sand in 1:5, and at fan & pad side. Heating System Electric heat blower system 2.5kw - 2 nos

Hi-tech Polyhouse with Fan & Pad System covered with UV sheet Single span(Size 500sqm) Size-500 sqm (includes side corridors) Length: 25 m, Width: 20m(2+8+8+2) Side Height- 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span- 02 GI pipe structure of BIS standards All Structure, Rafters, Purlins, Trusses are of GI pipe and as per ISI 1239/3601 standard. All pipes are of ISI standard with 1.8-2mm thickness. Foundation Pipe: 60mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe 76m OD x 2mm thickness GI Pipe. Bottom: 60mm OD x 2mm thickness GI Pipe. Arch Pipe: 42mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm ODx2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI Pipe Curtain Pipe: 20mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Poly lock profile will be made up of GI section fixed witth zig zag spring of GI material. Cladding Material High quality UV stabilized 5 layered, 200 micron thick with drip lock (anti drip) diffused, anti-dust, anti-condensed .Shade Net 50% UV stabilized provided inside the structure with manually folding spreading system, GI wire will be used to fix shade net with sliding arrangement for opening & closing as per requirement. Pulleys assembly with nuts & bolts will be provided Curtain Rings & curtain clamps with respect to standard specification will be provided. Side ventilation of insect net of 40 mesh, rolling curtains on two sides with manual rollup system Entrance Room & Door One Ante room of size 2m x 2m x 3m (LXWXH) will be provided and covered with UV stablizes 200-micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System Four way foggers fixed on 16mm laterals are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution with Grid 3mtr x 3mtr, Fogger discharge range:- 28 LPH with Monoblock pump 1.5HP Drip Irrigation 1. Network Pipes: Main:HDPE/PVC Pipe: 60mm 6kg as per as per IS: 4985:2000 S/M: HDPE/PVC Pipes: 50mm 6Kg used as laterial for drip irrigation 2. Fitting & Accessories: Heavy duty HDPE/PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3. Inline tube: Drip inline 16mm among each row with 2 LPH normal flow rate OR Sprinklers at the top. 4. LDPE Lateral Pipe: Misting line with 16mm 5. Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6. Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7. Filtration system: Screen Filter 12m3/hr 8. Air Release Valve: Long lasting and safe operation of system. Evaporatiing cooling system (ECS) for cooling system ECS Costruction Material:- ECO Friendly Aluminium Section: Tray side, Top etc . Cooling Media: (8m x 1.5m x 100mm) x 2 Nos thick cellulose pad Miscellaneous: Fasteners, Galvanized, Rivet-Aluminium PVC Pipe: 20mm/25mm/32mm with elbow & Tee for over flow & drain pipe Water Tank: PVC Tank 1000 Liters. Monoblock Pumpset: 1HP Exhaust 50" with 1.5 hp motor six blades - 4 Nos Automatic control system: Control Panel for Temperature, Humidity and Light will be fixed in Buffer Area. Relative Humidity + temperature controller Programmable, Cyclic timer, main switch (Rotary) Individual indicator with a main ON/OFF switch, Light indicator for main light, heating, cooling & humidity Plant Work Station/ Benches Benches consist of GI round pipes 20mm x 2mm thick. Nut bolts Bench top width will be 0.9m Length 50 RM Seedling trays having 99 cavities (250 nos) Standard illumination system: Two number LED 100-watt flood light will be provided in the poly house Brick work/ civil work Foundation base block height 2.5' x 9" x 9" each in CC 1:2:4, wall for Hi-Tech green house 1' below earth surface, 2.5' above earth surface 9" wide exposed surface plastered with cement sand in 1:5, and at fan & pad side. Heating System Electric heat blower system 2.5kw - 2 nos

AREA : 160SQM LENGTH : 20M WIDTH : 08M CENTRE HEIGHT : 4.0M SIDE WALL HEIGHT : 2.5M SHAPE : GOTHIC BUFFER ROMM : 2.0M X 2.5M STRUCTURE STEEL FRAM : Anti-corrosive, galvanized square pipe of ISI standard Trusses : beam type 47x47 mm x 2.6mm thick and 38x38 mm x 2.0mm thick to bear wind/snow load strength with load capacity of 0-100 kg/sqm and resist wind speed of 0-150 kmph suitable for Temperate regions of jammu & kashmir Poles supports : 47mm x 47mm x 2.6mm thick Purlin : 38mmx 38mm x 2.0mm thick runners : 32mm x 32mm x 2.0 mm thick Support : 32mm x 32mm & 25mm x25mm x 2.0mm thick Doors 2nos size 2.0m x 1m Cladding Materials Polycarobonate sheet specifiaction Thickness : 8mm triple walled Impact Performance : -40°C to +120°C Both side UV stabilized Sheetstructure : 8/3 U.L Temperature Rating : 100°C K valve W/M2k 3,5 Light Transmission : 78-80% Excellent Thermal Insulation : 3.5 Safe Fire Performance : Self-extinguishing and difficult to ignite Fixing by aluminium striping, Thermal safety: silicon Cooling system : ECS Frame: Coextrded aluminium bottom gutter, side & Top Gutter etc. Cooling media : Cellulose Pad size 8m x 1.5m x 100mm which give efficiency from 60 to 95% Miscellaneous : Fasteners, Galvanised, Rviet- Aluminium PVC pipe : 20mm/25mm/32mm with L& T Water tank : pvc Tank 1000 liters Mono block Pump : 1hp Slow speed axial flow fans - 2 nos Body size : 1200x1200x400mm , Number of blades: 6nos Blade : ss304 grade, shutter: steel speed of propeller : 460RPM approx Voltage : 380V/3-Phase/50HZ, Body Materilas : Galvanized steel Additional axial fan 600mm with SS blade to be installed above gutter ht 3 Nos 21" made of high quality stainless steel, fixed/mount with cable above Gutter height in green house, totally enclosed GB motor, to ensure excellent performance of cooling by circulating inner air. Humidification system This is very important feature of the Green House for growing of plants to increase inside Rh. Micreo fogging/misting : discharge range : 28l/p Head Control Unit Pattern: Hanging type : Pipe 16mm LLDPE colour Black Motor: 1.0 HP Monoblock pump : 1No. Filter Disc Tank : 500liter PVC Pipe : 32mm/25mm Automatic Control system Microprocessor based user friendly for Temperature humdity and light dual mode function installed in pre entry area, Power Input- 220-415 VAC, 50Hz. Three/Single phase, Ambient 5-50°C, RH up-to 90% a) Relative Humdity + Temperature Real Time Controller b) Timer for light c) Main switch (Rotary) d) Individual Indicator Shading Aarrangement of motor operated automatic rolling screens of 50% shade net, Material: UV resistant materilas, colour Green Electrical Device High quality ISI approved fittings with copper multi strand twisted FR Grade wires and rigid stds of safety with proper MCB copper cable ISI Mark MCB ISI Mark LED Light ISI Mark Air curtain Size: 1m wide heavy duty air curtain with blowers made of high quality with 1 HP Motor and Double Blower system, powder coated finish at pre entry point with auto main ON/OFF operation at the time of door opening/closing (One number to be provided) Civil Construction Excavation- Manual Excavation of 40cm deep below ground level having a width of 50cm. PCC : Lying of 1:5:10 mix on excavated of 4" thickness Foundation : Cemented concrete foundation (1:2:4) mix 2' below ground level and one feet above ground level Wall: Made of RR stone/cemented block 23cm width 40cm above and 30cm below GL 1:6 (1Cement : 6 fine sand ) Plastering : 1:6 (1cement : 6 fine sand) Path : Cement concrete in (1:2:4) mix of 50mm thick in paths/walk way 2' wide

Insect Proof Net House (Size 240 sqm) Size- 240 sqm (Includes side corridors), Length: 20 m , Width: 12 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -01 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick GI pipe structure of BIS standards Pipes for columns, purlins, trusse All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Insect Net 40mesh covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 2hp ( any reputed brand) water Tank 1000 liter- 1nos Drip Irrigation 1.  Network Pipes: Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 2hp Water Tank 1000 liter- 1nos Control system: Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Insect Proof Net House (Size 480 sqm) Size- 480sqm (Includes side corridors), Length: 24 m , Width: 20 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -02 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick GI pipe structure of BIS standards Pipes for columns, purlins, trusse All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Insect Net 40mesh covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 2hp ( any reputed brand) water Tank 1000 liter- 1nos Drip Irrigation 1.  Network Pipes: Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 2hp Water Tank 1000 liter- 1nos Control system: Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Insect Proof Net House (Size 1008 sqm) Size- 1008 sqm (Includes side corridors), Length: 36 m , Width: 28 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -03 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick GI pipe structure of BIS standards Pipes for columns, purlins, trusse All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Insect Net 40mesh covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 2hp ( any reputed brand) water Tank 2000 liter- 1nos Drip Irrigation 1.  Network Pipes: Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 2hp Water Tank 2000 liter- 1nos Control system: Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Naturally Ventilated Poly House (Size 240 sqm) Size- 240 sqm (Includes side corridors), Length: 20m , Width: 12 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -01 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 60mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 76mm OD x 2mm thickness GI Pipe. Bottom: 60mm OD x 2mm thickness GI Pipe. Arch Pipe: 42mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material HighqualityUVstabilized5layered(ofanyreputedbrand)LDPEsheet 200 micron thick with drip lock (anti drip) diffused, anti- dust, anti- condensed andproperties. Shade Net 50% UV stabilized provided inside the structure with manually folding spreading system (of any reputed brand) minimum 12-gauge GI wire will be used to fix shade net with sliding arrangement for opening & closing as per requirement. Pulleys assembly with nuts & bolts will be provided. Curtain rings & curtain clamps with respect to standard specification will be provided. Fabric UV stabilized (minimum 150 GSM) will be used for side apron which will be of 1m above ground level. Side ventilation of insect net of 30/40 mesh, rolling curtains on two sides with manual chain rollup system Entrance Room & Door OneAnteroomofsize2mx2mx3m(LXWXH)will be providedand covered with UV stabilizes 200- micron film. Two hinge doors of size 1mwidth&2mheightdoubledoorandmadeofpolycarbonatesheet. Fogging and Drip System: Four-wayfoggersfixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distributionofvapoursforgettinguniformclimaticcondition.(with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp(anyreputed brand) water Tank 1000 liter- 1nos Drip Irrigation Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.   Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wiresetc 3.  Inlinetube:InlineHydrogoal16mmdriplinglandamongeachrow with 2 LPH normal flowrate.4.  LDPE Lateral pipe: Misting line with16mm 5.   Head Connector & Gasket rubber grommet connect the PVC sub main pipeline. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gellateral. 7.  Filtration system: Screen filters of matchingcapacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing,non-drain,lowprofile,topoutlet,microtubes&pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 1hp Water Tank 1000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Naturally Ventilated Poly House (Size 480 sqm) Size- 240 sqm (Includes side corridors), Length: 24m , Width: 20 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -02 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 60mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 76mm OD x 2mm thickness GI Pipe. Bottom: 60mm OD x 2mm thickness GI Pipe. Arch Pipe: 42mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material HighqualityUVstabilized5layered(ofanyreputedbrand)LDPEsheet 200 micron thick with drip lock (anti drip) diffused, anti- dust, anti- condensed andproperties. Shade Net 50% UV stabilized provided inside the structure with manually folding spreading system (of any reputed brand) minimum 12-gauge GI wire will be used to fix shade net with sliding arrangement for opening & closing as per requirement. Pulleys assembly with nuts & bolts will be provided. Curtain rings & curtain clamps with respect to standard specification will be provided. Fabric UV stabilized (minimum 150 GSM) will be used for side apron which will be of 1m above ground level. Side ventilation of insect net of 30/40 mesh, rolling curtains on two sides with manual chain rollup system Entrance Room & Door OneAnteroomofsize2mx2mx3m(LXWXH)will be providedand covered with UV stabilizes 200- micron film. Two hinge doors of size 1mwidth&2mheightdoubledoorandmadeofpolycarbonatesheet. Fogging and Drip System: Four-wayfoggersfixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distributionofvapoursforgettinguniformclimaticcondition.(with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp(anyreputed brand) water Tank 1000 liter- 1nos Drip Irrigation Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.   Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wiresetc 3.  Inlinetube:InlineHydrogoal16mmdriplinglandamongeachrow with 2 LPH normal flowrate.4.  LDPE Lateral pipe: Misting line with16mm 5.   Head Connector & Gasket rubber grommet connect the PVC sub main pipeline. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gellateral. 7.  Filtration system: Screen filters of matchingcapacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing,non-drain,lowprofile,topoutlet,microtubes&pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 1hp Water Tank 1000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Naturally Ventilated Poly House (Size 1008 sqm) Size- 240 sqm (Includes side corridors), Length: 36m , Width: 28 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -03 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 60mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 76mm OD x 2mm thickness GI Pipe. Bottom: 60mm OD x 2mm thickness GI Pipe. Arch Pipe: 42mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material HighqualityUVstabilized5layered(ofanyreputedbrand)LDPEsheet 200 micron thick with drip lock (anti drip) diffused, anti- dust, anti- condensed andproperties. Shade Net 50% UV stabilized provided inside the structure with manually folding spreading system (of any reputed brand) minimum 12-gauge GI wire will be used to fix shade net with sliding arrangement for opening & closing as per requirement. Pulleys assembly with nuts & bolts will be provided. Curtain rings & curtain clamps with respect to standard specification will be provided. Fabric UV stabilized (minimum 150 GSM) will be used for side apron which will be of 1m above ground level. Side ventilation of insect net of 30/40 mesh, rolling curtains on two sides with manual chain rollup system Entrance Room & Door OneAnteroomofsize2mx2mx3m(LXWXH)will be providedand covered with UV stabilizes 200- micron film. Two hinge doors of size 1mwidth&2mheightdoubledoorandmadeofpolycarbonatesheet. Fogging and Drip System: Four-wayfoggersfixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distributionofvapoursforgettinguniformclimaticcondition.(with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp(anyreputed brand) water Tank 1000 liter- 1nos Drip Irrigation Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.   Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wiresetc 3.  Inlinetube:InlineHydrogoal16mmdriplinglandamongeachrow with 2 LPH normal flowrate.4.  LDPE Lateral pipe: Misting line with16mm 5.   Head Connector & Gasket rubber grommet connect the PVC sub main pipeline. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gellateral. 7.  Filtration system: Screen filters of matchingcapacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing,non-drain,lowprofile,topoutlet,microtubes&pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 2hp Water Tank 2000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Shade Net House (Size 240 sqm) Size- 240 sqm (Includes side corridors), Length: 20 m , Width: 12 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -01 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Shade Net 50/75% covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp ( any reputed brand) water Tank 1000 liter- 1nos Drip Irrigation Network Pipes Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 1hp Water Tank 1000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Shade Net House (Size 480 sqm) Size- 480 sqm (Includes side corridors), Length: 24 m , Width: 20 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -02 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Shade Net 50/75% covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp ( any reputed brand) water Tank 1000 liter- 1nos Drip Irrigation Network Pipes Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 1hp Water Tank 1000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Shade Net House (Size 480 sqm) Size- 1008 sqm (Includes side corridors), Length: 36 m , Width: 28 m Side /Gutter height 4 Mtr Centre Height 5.5 Mtr Bay Width 8 x 4 Mtr No of Span -03 Structure Folding/dismantlable, on nut bolts, structure made of 60mm, 48mm, 32mm (OD), 1.8- 2.00 mm thick Pipes for columns, purlins, trusses All structure, Rafters, Purlins, Trusses are of GI pipe and as per IS 1239/3601 standard. All pipes of ISI standard with 2mm thickness. Foundation pipe: 48mm OD 2mm GI Pipe. The foundation pipe will be 4 ft. Column Pipe: 60mm OD x 2mm thickness GI Pipe. Bottom: 48mm OD x 2mm thickness GI Pipe. Arch Pipe: 48mm OD x 2mm thickness GI Pipe. Purlins Pipe: 42mm OD x 2mm thickness GI Pipe Bracing Pipe: 32mm OD x 2mm thickness GI pipe Corridor: 48mm OD x 2mm thickness GI Pipe Clamps, Easterners and Nut Bolts Galvanized with good quality of plating to have good anti corrosive properties Foundation/civil work Columns are fitted over ground bolted to insert pipe of 60mm/50mm*2mm thick compatible GI pipe, length of insert 1 to 1.1m of 30cm x 90cm size in 1:2:4 PCC ratio Poly lock profile will be made up of GI section fixed with zigzag spring of GI material with stand the maximum wind load. Cladding Material Shade Net 50/75% covered with top and sides. Entrance Room & Door One Ante room of size 2m x 2m x 3m (L X W X H) will be provided and covered with UV stabilizes 200- micron film. Two hinge doors of size 1m width & 2m height double door and made of polycarbonate sheet. Fogging and Drip System: Four-way foggers fixed on 16mm laterals (of any reputed branded) are to be installed just below the shade net with sufficient overlapping to get uniformly in distribution of vapours for getting uniform climatic condition. (with Grid 3mt x 3mtr), Fogger discharge range: - 28 LPH with Motor/Centrifugal pump 1hp ( any reputed brand) water Tank 1000 liter- 1nos Drip Irrigation Network Pipes Main PVC Pipes: 60mm 6kg. as per IS: 4985:2000 S/M: PVC Pipes: 50mm 6kg used as lateral for drip irrigation. Drain PVC Pipes: 40mm 6 kg. 2.  Fitting & Accessories: Heavy duty- including the PVC, elbow, Tee Bend solvent cement, filter flanged, GI wires etc 3.  Inline tube: Inline Hydro goal 16mm drip ling land among each row with 2 LPH normal flow rate. 4.  LDPE Lateral pipe: Misting line with 16mm 5.  Head Connector & Gasket rubber grommet connect the PVC sub main pipe line. 6.  Barbed Connector: Barbed connector 16mm to connect the inline land hydro gel lateral. 7.  Filtration system: Screen filters of matching capacity Dripper: 2 litre/hour, with 30cm dripper to dripper distance self- flushing, non- drain, low profile, top outlet, micro tubes & pegs. 9. Air Release Valve: Long lasting and safe operation of system. 10.Control Valve: Appropriate required the timely opening and closing system must be Operation Pump- 2hp Water Tank 2000 liter- 1nos Control Panel With a main ON/OFF switch (reputed make), Light Indicator for main light, starter for Drip Irrigation system and fogging system.

Supply, Fabrication & Installation of Sanitizing Tunnel structure size 8’x5’x8’ (LxBxH) made of M.S. Square Pipe 40x40mm (16 Gauge) for structure, M.S. Square Pipe 25x25mm for roof and internal support duly painted with white color including red oxide primer coat. Two sides fitted with ACP (Aluminum Composite Panel) 3mm Sheet & on the top color coated sheet. Fogging System consists of 6 nos foggers, lateral 16mm as submain & 32mm as main pipeline alongwith fitting & accessories. Water Storage Tank Capacity 500 Ltr – white color (minimum 3 layers) alongwith Mono block Pump of 1 HP (ISI Mark) alongwith fittings & accessories. Antiskid mat 5’x8’ for flooring. The structure shall have provision of LED bulb alongwith switchboard of mono block pump. The entrance & exit of the tunnel shall be covered with transparent sheet of standard quality. Providing flex as per logo design provided by the intending department. (Complete Job)

Student Bench: Student seating benches 3 tier, size 6’-length 7’-wide 7’ height above ground level from back side and 1’height above ground level from the front side. Frame made of Angle Iron comprising of isi: of 40x40x5mm and flat iron comprising of ISI: of 40mmx5mm, each seating step of 6’x2’, each tier height be of 18”and height of the top seat resting back be 18”also. Front step size be 6’x1’. Vertical angles on back side be welded in box shaped design for strengthening. Structure be Pre coated with Primer and enamel paint of black color.

Stadium Shed: Providing and fixing of Stadium Shed made out of MS angle 40mmx40mmx5mm in box shaped welding with arc design and purlins of 40mmx40mmx2.9mm MS hollow section square pipe. columns made of 6”x6” rectangular section (two sections of 6”x3” welded to give it a shape of 6”x6”) and fitted with L’ shaped 4”x4” rectangular section ( two sections of 4”x2” welded to give it a shape of 4”x4”). Also providing polycarbonate sheet of 0.5mm on top fitted with GI nuts and bolts. All structure be pre coated with primer and enamel painted in black color.

Staff Parking Shed (Semi Circle Shaped): Staff parking shed (Semi Circle Shaped ) , Structure made out of Angle Iron of 32mmx32mmx5mm welded in box shaped. columns Made of MS Steel round pipe 3” dia ISI standard fitted with gusset plates with trusses in semi circle shape made of angle iron 32mmx32mmx5mm and flat iron 32mmx5mm . Also provide the polycarbonate sheet of 0.5mm on top for roofing and sides of the arc shaped trusses fixed with G.I Strips, nuts and bolts.

Student Parking Shed: student parking shed, parking shelter made out of tubular trusses made out of rectangular hollow section 96mmx48mmx3.2mm structural steel confirming to is:4923 with a spacing supported on columns of MS steel 3”dia round pipe fitted with gusset plates. The struts shall be made of 66mmx33mmx2.9mm rectangular hollow section with providing polycarbonate sheet of 0.5mm on top fitted with GI nuts and bolts. All structure be pre coated with primer and enamel painted in black color.