Sher E Kashmir University Of Agricultural Sciences And Technology Tender

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4(1 cement :2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6(1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing form work including Centering, shuttering, strutting, propping etc. using ply wood sheeting with water proofing ply board (12 mm min. thickness) and removal of the same for ( All work at all levels complete.)

Steel work in built up tubular (round, square or rectangular hollow tubes//pipes etc.) including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing Track deck crill make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anticapillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness )

Asper item above for plain .50mm total thickness SMP coated galvanised steelof similar material for ridge, caping pieces places at apex of sky lights/hips. Valleys etc incl. noteing turning down of edges of capping between ribs etc complete (500mm to 1000mm)

Providing wood work in frames of doors, windows, clerestory windows and other frames Wrought framed and fixed in positions (Its class Kail wood).

Providing and fixing 35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : First Class Kail Wood

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters.(80x1.25 mm M.S. laths with 1.25 mm thick top cover)

Providing and fixing ball bearing for rolling shutters

Providing/fixing welded mesh 25 mm x 25 mm aperture including priming coat of steel primer and two coats of painting etc. complete

Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work till complete in all respects.