HP Krishi Vishva Vidyalaya Tender

Supplying and drawing following size of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required. (Polycab/KEI/Finolex make).

3x1.5 Sq. mm.

5x1.5 Sq. mm.

3x2.5 Sq. mm.

3x4.0 Sq. mm.

5x4.0 Sq. mm.

3x6 Sq. mm.

3x10 Sq. mm.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. (Finolex/D-plast/Anchor make) 25 mm. dia.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required. (Anchor make) Less the cost of fan regulator (222-40=182)

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required. (ISI mark.) and accessories of anchor make.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required. (ISI mark.) and accessories of anchor make.

Supplying and fixing ceiling rose on the existing junction box / wooden block including connections etc. as required. Anchor (Jumbo 2/3 plate)/Havells make.

Supplying and fixing bakelite batten/angle holder including connections etc. as required:- (Anchor/Havells make)

Supplying and fixing copper strip bus-bars suitable for 100 Amp. 415 volts capacity 4 No. each of cross-sectional area (25.4mmx3.17mm),in the existing enclosure with all accessories including connections etc. as required. (ISI mark)

Supplying and fixing copper strip bus-bars suitable for 200 Amp. 415 volts capacity 4 No. each of cross-sectional area (25.4mmx4.75mm),in the existing enclosure with all accessories including connections etc. as required. (ISI mark)

Providing and fixing following rating, four pole, 415 volts, On-Load change over switch unit, panel mounting, front handle operation, including drilling holes in the cubical, making connections, etc. as required. (L&T / C&S Make)160 Amps.

Providing and fixing following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubicle panel, making connections, etc. as required.

100 Amp. -16 KA (Four pole) (L&T / C&S/ Havells Make)

125 Amp. -16 KA (Four pole) (L&T / C&S/ Havells Make)

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. Single pole. Cat-A. (L&T/ C&S/Legrand/Havells Make)

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. Double pole. Cat-A. (L&T/ C&S/Legrand/ Havells Make)

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps. Cat-A. (L&T/ C&S/Legrand/ Havells Make)

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required. (L&T / Legrand/ Havells Make)

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-Double door-12 way (L&T / C&S / Legrand Make)

Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-Double door-8 way (8+24), horizontal type (L&T / Legrand/ Havells Make)

Earthing with G.I. earth plate 600 mmx600 mmx 6 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Supplying and laying 25mmx5mm G.I. strip at 0.50 mtr. below ground level for earth electrode conductor, including soldering etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long G.I. tube, having single prong at top, with 85 mm dia 6 mm thick copper base plate including holes etc. complete as required.

Riveting, sweating and soldering of copper/ G.I. tape ( with another copper/G.I. tape, base of the finial or any other metallic object) as required.

Supplying and fixing G.I. tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run)

Supplying and fixing G.I. tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run)

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size:- (KEI/Polycab/Hevells/L&T make)

Armoured cable 6 sq. mm (twin core)

Armoured cable 70 sq. mm (3.5 core)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required. Ceiling Fan 1200 mm sweep, Category-A. Crompton (Smart breeze stylish design white)/Bajaj (speedster white) make

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required. Exhaust Fan, Light duty, (Domestic) 300 mm sweep. Crompton (Brisk Air Neo) make.

Supplying and erection of 3 stepped steel tubular swaged and welded pole of suitable length and dia. to be fixed up to a required planting depth below G/L in a hole of excavation about 30 cm dia. and of suitable depth, to be filled in up to 15 cm below G/L with 1:3:6 cement concrete and there above plinth with 1:2:4 cement concrete up to a height of 45 cm from G/L. The radial thickness of the plinth above G/L should not be less than 6.35 cm and sufficient to completely flush a 180 mmx100 mmx 45 mm deep, glass filled Nylan F.R. grade box for housing a 16 Amp. MCB, the outer surface of the plinth to be finished with 1:3 cement plaster 6 mm thick, the fuse-box shall have a water tight cover, including painting of pole with two coats of approved color, brand and manufacture of paint over a priming coat complete in all respects as required Overall length 7 meter, with planting depth 1.25 m, length of sections 4 m, 1.5m and 1.5m (bottom, middle and top respectively), outer dia and thickness of sections 127mmx4.5mm, 101.6mmx3.65mm and 76.1mmx3.25mm (bottom, middle and top respectively) with approximate weight 74 Kg

Supplying and erection of street light bracket made of G.I. pipe 'A' class of suitable length and dia, the pipe bended to give an angle of 100 to 110 degree fitted with bolt & nuts at the top of existing pole or wall including painting the pipe with two coats of approved paint over priming coat complete in all respects as required 32 mm dia. G.I. pipe, heavy class

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 75 mm dia (OD-75 mm nominal) ( D-Plast/finolex make)

Supplying and erection of sheet metal cubical pedestal / wall mounted cubical panel of made from 1.6 mm thick M.S. sheet duly fabricated in a segregated manner for housing of switch fuse units, erection of MCCBs/switchgears with tinned copper shredders, thimbles, separators, insulators etc., also fixing of Bus bars with thimbles,heat sinkable sleeves of red , yellow and blue coloured , porcelain cleats nuts and bolts etc, Panel should be welded with each compartment on five sides & front side hinged, insulated Gaskets, etc complete with locking arrangement with sufficient numbers of vertical and horizontal intermediate members for housing switchgear/MCCBs/ MCBs in separate compartments including wiring of switchgears with suitable copper cables/ copper strips. It should have digital metering unit (with ammeter, Voltmeter, selector switches, CT unit red, yellow and blue coloured indicator lamps etc.) The cubical pedestal shall have cable entry box at two sides, with epoxy powder coated approved paint and bonding to the existing earth etc. and as per entire satisfaction of Engineer-In-charge.

Providing and fixing ultra slim polycarbonate LED batten tube lighting fixture with high lumen output, environmental friendly,energy efficient ready to use pack complete with all accessories, connections, testing and commissioning etc. as required. 40 watt-LED (Havells /Panasonic/Crompton make)

Providing and fixing Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution with complete with all accessories, connections, testing and commissioning etc. as required. 24 W LED 6500 K (Havells /Panasonic/Crompton make)

Providing and fixing LED outdoor luminaries energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66/IP67 luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith Street light bracket, electronic driver complete with all accessories, connections, testing and commissioning etc. as required. 50W LED 6K (Havells /Crompton/Bajaj make)

Supplying and fixing twin core PVC insulated weather proof aluminium conductor cable with GI bearer wire 8SWG as required complete in all respect. 2 Core 6 sq mm (ISI mark)

Supplying and drawing electrolytic grade solid annealed bare copper conductor, 4 Pair unshielded twisted pair (UTP) CAT 6 Industrial cable with PVC Sheath for LAN Network in existing surface / recessed, Steel/PVC conduit as required. (D-link make)