Himachal Pradesh Irrigation And Public Health Department Tender

Total Head 13.30 Mtrs

Type of water and its source Clear water from Sadimentation tank

Supply of Kirloskar/ Kilburn/Leader make Cast iron double flanged swing check type reflux valve of class PN 1.0 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for with standing nominal seat presure of 10.20 Kg/Cm2 confirming to BIS 5312-1984 Part-II) The size & class of valve shall be specified by the tenderer).

Supply of standard make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock.copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Total Head 39.51 mtrs

R.P.M. of pumping set. 1450/2900 RPM

Test run. 8 Hours continueously for 7 days

Limit of pump operation. In the completetion Rage of (-) 75%

Providing , Welding & fixing of MS flanges to confirming to IS 6392-1971 ( Latest with upto date amendments) of flange table with MS tubes in Two layer on outer face & one layer on inner face to make the joint leak proff. The thicknes of gasket not less then 3.00 mm confirming to IS 2712-1965 complete in all respect and to the best satisfaction and direction of Engineer -in-charge with in all leads & lifts. Flange to be welded after 100 mtr interval of pipe.

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

Submersible Pumpng Machinery Supply and Erection of submersible porder Raw water pump of KSB/Kirloskar/Kilburn/Model KRTE single and open impeller make conforming to BIS; 5669-1970 latest suitable for lifting RAw water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments)1450 RPM) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motoron suitable for operation on 415+ 10% volts, 3 phase including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:-

Depth of Jack Well 6.00 mtrs

e) TDS 610 PPM, f) other depth of well assembly

Characteristic of water

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 1 No. pump of rating 20 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

No of working hours per day 20.00 Hours

No. of pump required 1.00 No. (0 will act as standby)

d) PH 6.5 to 8.5

On supply side of 3½ core coper cable 2.50 mm^2 ( From HPSEB Meter to Switch & Starter).

Providing and fixing of Kirloskar/Kilburn/Leader make cast iron double flanged swing check type Reflux valve of class PN 1.6 having bye pass arrangement (to be provided on delivery side) of size of 1 size higher than the delivery size of pump and shall be suitable for withstanding normal seat pressure of 16.32 kgs/cm2 confirming to BIS-14846-2000 part-II) The size & class of valve shall be specified by the tenderer)

Delivery pipe ….. mm dia (size to be specified by the tenderer)

Type of current. AC Three phase supply with frequency of 75 cycle 75 second

150 mm Dia GI pipe ( Medium Class) (Booster stage 80 mtr, and 470 mtr rising main (550 mtr) Table -5

RL of discharge heighest point 364.50 mtr

Suction pipe …..mm dia (size to be specified by the tenderer)

c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr

Laying, of pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set. The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of

On motor side 3 core flat joint less copper cable of size 2.50 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Static Head 29.50 mtr

No of working hours per day 20 Hours

Energy saving Variable frequency drive starter of 20 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should be able to withstand ambient temperature 50 Degree celcius without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make:- L&T/Conserve/Schmeder/Aarmation1 No. 3 (ii) Main incomer MCCB of suitable capacity of L&T/ Schmeder/ABB/Siemens make on the coming feeder for pumping set confirming to BIS-2516-1985 ( Latest edition) 1 No. 3(iii) LED Three phase inicating lamps complete with logged switches for individual motore confirming to BIS 3452 ( Part I &II) latest with upto date amendments ( 1 No. ) 3(iv) LED On/Off Lincommer MCCB with proper short circuit capability for both the starters make L&T / Schinieder/ ABB ( 1 No. ) 3(v) On / Off & Trip indicator and push button, control and power wiring Power capacitor ,Cooling fan 230 VAC Control terminal , Buss Bar i.e. Bolt , insulator etc ( 1 No. ) 3( v) Selector switch for Auto and Manual Oparation 1 No. 3 (vi) Input Choke of required HP for Energy saving variable frequencty Starter which shoud be installed at the input of Energy saving variable frenqencty starter, so that there whould be proper protection in case of any voltage surge and distortons 2 No. 3 (vii) Control Transformer Make Surge supressor device with isolating MCCB to circunate the power surges due to lightening and system surges 1 No. 3 (viii) Power and Control Wiring and Busbar 1 No. 3(ix) Installation, commissioning and Software Development 1 NO. 3 (x) Surge supressor debvice with Isolating MCCB toeleminate the power surge due to lightening and system surges 1 o. 3 (xi) Power quality monitoring & controlling relay with Control Contactor to safeguard Electronic and Electric elements 1 No. 3 (xii) Independent Cont4rol Panel with stiwth Fuse Unit and Fuses fo Suitable Amperage to eliminate the Kit Kat fuses of HPSEB Make Aarmaton/Siemens/ Schnieder/ L&T 1 No. Automation System for Unmannede Oparatins with SCADA features, PLC, HMI and Level Sensor :- (i) PLC (Programmable logic controller) with appropriate digital and analog and inpute and output to give automatic command to Star Deltar Starer Panel energy saving Variable Freqency Starter Panel Make Aarmation Electric Bechoff Automation/ Rockwell Automatin 1 No. (ii) Electronicrelay card & channel 1 No. (iii) SMPS 4.5 amps to energise PLC system 1 No. (iv) HIMI (Human Machine Interface) 7" display for Monotring and Controllling of Submersibnle pumps Make : Aarmation Electric/ Bechoff Automation / Roackwell 1 No. (v) Conrol MCB for Automation System 1 No. (vi) Level Sensor to indicate the water level of tank remotely 1 No. (vii) Shielded Data Cable for Communation of Level Snsor with PLC 1 No. (viii) Supply of Mobile App (Android IOS) with User ID and Password to monitor and control the pumping oparation from Mobile for 3 users Make Aarmation Electric/ Bechoff Automation Rock well Automation (ix) Could Gate way for Data Clouding to Server 1 No. (x) SCADA soft ware to be installed in Laptop/PC on remotely monitor and control the operation of pumps and also to anysis the pump start and stop history logging fuilt starter, fault history, Power quality Parameters like PE Current Voltage KWH THD etc Make Aarmation electric/ Rockwell Automation Rockwell 1 No. (xi) Cloud space for data storae at cloud/ server 1 No. (xii) Inatallation Commissioning and Software Development.

Rate Voltage 415V+ 10%

150 mm Dia flanged Table -5

Dia of Rising main 150 mm GI medium pipe 4.80 mm thickness

Length of R/Main 80.00 mtrs.

R.P.M. of pumping set. 2900 RPM

Errection of all equipment including Cost of Tees bends Taper & any other fitting required as per site Condintion & as per Direction of Engineer in Charge.

b)Turbidity NTU 113 NTU

No. of pump required 1.00 Nos. (0 stand bye)

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

a)Ambient Temperature dig.c 20 dig. C

Rate Voltage 415+ 10%

Location of the site of installation of machinery. The site is located at a distance of 27KM from Pathankot (Chakki) Railway Station

Length of R/Main 470.00 mtrs.

Delivery Pipe ___mm dia G.I. medium class. (Size to be specified by the tenderer)

Discharge required from 17.41 LPS of each pump

Laying, jointing & testing in trenches to be levelled to grade, BIS marked GI flanged pipes confirming to BIS:1239 (latest with upto date ammendments) of following mm dia (Medium class) duly flanged after 100 Mtrs. With intermediate butt welded joints including the cost of flanges, bends/short pieces made from parent tubes of diferent degrees cutting welding and jointing with flanges conforming to tables as specified below of BIS: 6392 (latest with upto date ammendments) welded at both ends as per BIS:816 (latest with upto date ammendments) with electrodes confirming to BIS 814 (latest with upto date ammendments) & provided with nuts and bolts BIS: 1369 (latest with upto date ammendments) of required sizes 4 mm thick champion make compressed asbestos fiber gasket or synthetic rubber gasket confirming to BIS:2712 (latest with upto date ammendments) & approved specifications as per site conditions including flushing, cleaning & hydraulic testing complete to the best satisfaction of Engineer-in-charge.(The Cost of Earth Work, MS Flanges & Gasket sheet etc. will be measured & Paid Saparitaly)

Location of the site of installation of machinery. The site is located at a distance of 27 KM from Pathankot (chakki) Railway station by road & 0.100 KM on head load (for the installation of both machineries.

supply of Kirloskar/Leader make Cast iron PN 1.6 double flanged swing check type reflux valve having bye pass arrangaement equal to Rising main i.e. 150mm dia) of size and shall be suitable for with standing nominal seat pressure of 16.32kg/cm2. confirming to BS-5312-1984 (latest with upto date ammendments).

c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr

Laying, of pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of

a)Ambient Temperature dig.c 20 dig. C

Supply of Kirloskar/Kilburn/Leader make double flanged cast iron Sluice valve having size one dia higher than pump size to delivery Pump class PN 1.0 conforming to BIS- 14846-2000 latest with upto date ammendments having seat pressure 10.20kg/ cm2 complete in all respect. within all leads and lifts. (Suction side)

Type of current. AC Three phase supply with

The Altitude of installation. 456 MLS

b)Turbidity NTU 113 NTU

Common header …… mm dia (size to be specified by the tenderer)

Test run. 8 Hours continueously for 7 days

Test run. 8 Hours continueously for 7 days

RL of pump shaft/ central exis 329.00 mtrs

Laying, Jointing & testing of Rising main 150mm dia 550 mtr (M) class Booster stage to stage-Ist Excavation in foundation treanches(Pipe & Pits) up to all depths in all classification of earth work such as pick work,jumper work,saturated soil including bailing or pumping out water,blasting soft /hard rock where blasting is prohibited in all lifts including trimming & dressing of sides leveling of beds to correct grade i/c shoring/strutting planking,timbering & dewatering wherever required stacking the usable & unusable material/soil separately & after laying,jointing & testing of pipes,returning the useable soil in trenches in 15cm layers including consolidating of such deposited layer by raming & watering & then disposing of all surplus excavated soil/unusable material as directed with in all leads & lifts including restoration of unmetalled surface to its original condition & including cost of diversion for traffic,night signals,fixing caution boards,crossing over trenches for access to houses,fencing etc.completein all respects with in all leads & lifts as per directions of Engineer-in-Charge.

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Charactristics of water. -

Limit of pump operation. (-) 15 % (+) 10% of total head

Energy saving Variable frequency drive starter of 7.50 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should be able to withstand ambient temperature 50 Degree celcius without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make:- L&T/Conserve/Schmeder/Aarmation1 No. 3 (ii) Main incomer MCCB of suitable capacity of L&T/ Schmeder/ABB/Siemens make on the coming feeder for pumping set confirming to BIS-2516-1985 ( Latest edition) 1 No. 3(iii) LED Three phase inicating lamps complete with logged switches for individual motore confirming to BIS 3452 ( Part I &II) latest with upto date amendments ( 1 No. ) 3(iv) LED On/Off Lincommer MCCB with proper short circuit capability for both the starters make L&T / Schinieder/ ABB ( 1 No. ) 3(v) On / Off & Trip indicator and push button, control and power wiring Power capacitor ,Cooling fan 230 VAC Control terminal , Buss Bar i.e. Bolt , insulator etc ( 1 No. ) 3( v) Selector switch for Auto and Manual Oparation 1 No. 3 (vi) Input Choke of required HP for Energy saving variable frequencty Starter which shoud be installed at the input of Energy saving variable frenqencty starter, so that there whould be proper protection in case of any voltage surge and distortons 2 No. 3 (vii) Control Transformer Make Surge supressor device with isolating MCCB to circunate the power surges due to lightening and system surges 1 No. 3 (viii) Power and Control Wiring and Busbar 1 No. 3(ix) Installation, commissioning and Software Development 1 NO. 3 (x) Surge supressor debvice with Isolating MCCB toeleminate the power surge due to lightening and system surges 1 o. 3 (xi) Power quality monitoring & controlling relay with Control Contactor to safeguard Electronic and Electric elements 1 No. 3 (xii) Independent Cont4rol Panel with stiwth Fuse Unit and Fuses fo Suitable Amperage to eliminate the Kit Kat fuses of HPSEB Make Aarmaton/Siemens/ Schnieder/ L&T 1 No.Automation System for Unmannede Oparatins with SCADA features, PLC, HMI and Level Sensor :- (i) PLC (Programmable logic controller) with appropriate digital and analog and inpute and output to give automatic command to Star Deltar Starer Panel energy saving Variable Freqency Starter Panel Make Aarmation Electric Bechoff Automation/ Rockwell Automatin 1 No. (ii) Electronicrelay card & channel 1 No. (iii) SMPS 4.5 amps to energise PLC system 1 No. (iv) HIMI (Human Machine Interface) 7" display for Monotring and Controllling of Submersibnle pumps Make : Aarmation Electric/ Bechoff Automation / Roackwell 1 No. (v) Conrol MCB for Automation System 1 No. (vi) Level Sensor to indicate the water level of tank remotely 1 No. (vii) Shielded Data Cable for Communation of Level Snsor with PLC 1 No. (viii) Supply of Mobile App (Android IOS) with User ID and Password to monitor and control the pumping oparation from Mobile for 3 users Make Aarmation Electric/ Bechoff Automation Rock well Automation (ix) Could Gate way for Data Clouding to Server 1 No. (x) SCADA soft ware to be installed in Laptop/PC on remotely monitor and control the operation of pumps and also to anysis the pump start and stop history logging fuilt starter, fault history, Power quality Parameters like PE Current Voltage KWH THD etc Make Aarmation electric/ Rockwell Automation Rockwell 1 No. (xi) Cloud space for data storae at cloud/ server 1 No. (xii) Inatallation Commissioning and Software Development.

Type of water and its source Clear water from J/ Well

Providing and Installation of Centrifugal Pumping Machinery Supply of horizontal spindle horizontal radial split casing/and suctions (back pull out arrangement) Single/double/ multistage centrifugal pumps or combination of pumps in series/parellel of KSB/Mathur & Platt/Jyoti/ Kirloskar/ BE/Maxflow/ Beaconweir make conforming to BIS 1520-1980) Latest with up to to date amendments, read with BIS: 9137-1978 (latest edition) suitable for lifting water of under mentioned characteristics with bronze/Suitable alloy, priming funnels, casing ring and shaft motor of bronze, shaft of steel grade ASA-410 with cast iron casing coupled directly through a flexible coupling on a common MS/Cast steel plate (base plate from the principal manufacturer of pumping set) to coupling sliperring squirrel cage screen protected drip proof electric induction motor/ motor of standard make such as Kirloskar/ NGEF/Cromption/Siemen/Jyoti/BHEL/GEC/ABB conforming to BIS 325-1978) read with BIS 900-1972( latest with upto date ammendments) it should include the cost of bearings, nuts & bolts,m painting etc. and shall be and suitable for operation on the data given below:

Discharge level of highest point 337.20 mtrs

On motor side 3 core flat joint less copper cable of size 4.00 mm² (From Switch & Starter to Motor) pump installed in the bore.

Dia of Rising main 150 MM G.I. (M). pipe 4.8mm thickness

Total head in Mrs 13.30 mtrs.

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay! Gloster make conforming to BIS 1554 (Part I)-1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

LWL in Jack Well 329.00 mtrs.

RL of Pump Shaft 335.00 mtr

e) TDS 5000 to 6000 PPM

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 1 No. pump of rating 7.50 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

On supply side of 3½ core coper cable 6.00 mm² (From HPSEB Meter to Switch & Starter).

f)Other -

d) PH