Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

a). 300x16 mm (three hundred into sixteen milimetre)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete

a). 200x10 mm(two hundred into ten milimetre)

b). 150x10mm(one hundred fifty into ten milimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

a). 125mm(One hundred twenty five milimetre)

b). 100mm(one hundred milimetre)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Single rubber stopper.

Providing and laying vitrified floor tiles Glossy in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, (Kazaria/ Nitco/ Somany/ Orient bell make), in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete complete in all respect as per satisfaction of Engineer-in-Charge a). Size of tile 600x600mm

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge a)Two or more coats on new work

Providing and applying white cement based putty of average thickness one mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) One or more coats on old work

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) One or more coats on old work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 Sqm and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge a).With cement mortar 1:4 (one cement : four sand)

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge ( upto 2 Sqm area or below ).

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within all lead as per direction of Engineer - in - charge. a). Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) .

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within all leads, lifts and carriage of material as per direction of Engineer-in-Charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within all leads etc. complete as per direction of Engineer-in-charge. a). In cement mortar

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking in all lead etc. complete in all respect as per satisfaction of Engineer-in-Charge a). Thickness above 10mm to 25mm.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Area 3 sq. metres and below.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm PVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make). a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make). a)White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make).

Providing and fixing P.V.C 32mm semi rigid waste pipe for sink, uniral and wash basin etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing 15 mm nominal dia. Internal G.I. pipes (medium grade) complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. complete in all respect as per satisfaction of Engineer-in-Charge. (Jindal/ Surya make).

Providing and fixing 45 cm length and 15 mm nominal dia uplasticised PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ zar make).

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ zar make).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) (Jindal / Hindalco make)

a). Powder coated aluminium (minimum thickness of powder coating 50 micron for fixed portion / frame work.

b).Powder coated aluminium (minimum thickness of powder coating 50 micron for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). a). With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm).

Providing and fixing zebra roller blinds of superior quality with required accessories complete in all respect as per satisfaction of Engineer-in-Charge (Vista/ Bizal/Nova/ Shadex make).

Supplying and installation of Research module Laboratory Units (Waldner / Kotterman / Godrej make) with work surface of following size with V-groove type moulding jet black Granite 20mm + - 2 mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under Storage Unit with Cam lock 900 Ht. with metal Shutter MT-1200W-600D-900 H – 3 Nos. AT-600W-600D-900 H – 1 No. AT-1200W-600D-900 H – 1 No. Under Bench Cabinet 600W-450D-674H-2S – 4 Nos. LS –600W-P – 3 Nos. REAR SIDE PANEL- 600-9H – 4 Nos. SIDE PANEL FOR SINK UNIT – 1 No. INLINE SINK UNIT 750W x 600D x 9H – 1 No. PP DROP IN SINK 560 x 355 – 1 No. MAIN STORAGE UNIT WITH METAL DOOR1950x900x450mm – 1 No ADD-ON STORAGE UNIT WITH METAL DOOR1950x900x450mm – 1 No