National Institute Of Technology Tender

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

5x6 sq. mm

Providing and fixing aluminium American type handle of size 200 mm anodised ( anodic caoting not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade, with SS screws etc. complete as per direction of Engineer-incharge

ROOFING

(Electrical works

With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles

40 A

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in- charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge.

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Powder coated minimum thickness 50 micron aluminium

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/ DLP trunking / in the furniture etc. as required.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

Providing and fixing vertical blind of 100 mm in width in any colour of vista or equivalent as approved by engineer in charge.

Supply, Installation, Testing and Commissioning of Air-cooled Cassette AC unit comprising of Scroll/ Rotary/ Twin compressor. The indoor unit shall be complete with DX coil, filters, blower section with motors & drive refrigerant piping, electronic expansion valve distributer, starter and other necessary controls. Each indoor unit shall have condenser coil, fans with motors and drive, single compressor, factory pre- charged with R410/R32/R404 Refrigerant gas, oil, and factory fitted re frigerant service valves and Electronic Expansion Valve, HP/LP cutout. The unit shall have electrical safety features like, phase reversal. All items should be encased in enamel painted anti corrosive, sheet metal cabinet. The heat exchanger for outdoor shall be constructed with copper tubes mechanically bonded to aluminum fins to form a cross fin coil. The Condenser fins must be coated with Anti- corrosive treatment. Cassette AC- R410/R32/R404 Fixed speed Cooling Only 2.0 TR Cassette AC Make: Carrier/Daikin/O- General/Toshiba

Supplying, installation testing and commissioning of recess mounting type LED of 2'x2' size(N.S.) with aluminium/CRCA powder coated housing anti glare diffuser with separate energy efficient electronic driver with efficacy better than 130 lunen/watt (minimum total lumen delivered package 3200) with CCT =4000k or 5700k as approved by engineer-in-charge. PF0.95 THD10% and with APFC CCCV driver having efficiency85 % service life of 50000 hrs @ L70 etc. complete i/c hanging arrangement with steel chain/steel wire and steel fastner hook i/c making suspension arrangement with gear Wire Including connection with 3x1.5 sq.mm. FRLS PVC insulated copper conductor cable in GI /steel flexible pipe etc as required. (Makes - Trilux Troffer X LEDPhilips RC380B LED36S -6500 GS PSU WH/LT Cat no. 002457 R000- Optima Venture- Maple Neo Recess)

Supplying and fixing following rating, four pole, 415 V, isolator in existing MCB DB complete with connections, testing and commissioning etc. as required.

NON SCHEDULE ITEM

For fixed portion

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

Pre-laminated particle board with decorative lamination on both sides

CIVIL WORK -WOOD AND PVC WORK

300x16 mm

63 A

Cassette Air conditioning system

Air conditioning Work

Powder coated aluminium (minimum thickness of powder coating 50 micron)

With stainless steel cover plate minimum 1.25 mm thickness

ALUMINIUM WORK

300x10 mm