Directorate Of Urban Local Bodies Tender

The lever of see saw shall be made from 80 mm NB ‘ GI pipe. The seat of see saw shall be made from FRP (Fiber Reinforced Plastic) / LLDPE (Low linear Density Poly Ethylene) 2 -3 thickness. The lever shall be fitted on 50 mm GI pipe and bush bearing shall be made from seamless pipe fitted in 80 mm NB GI pipe. See saw lever shall be welded with 150 x 150 x 5 mm MS plate for nut bolting with stand. All parts to be powder coated with minimum thickness of 40 microns uniformly and then fixed in cement concrete blocks of required size and mix etc complete as per drawing / sketch and direction of Engineer –in-charge at the site.

CHEST PRESS DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2150mm. (Height). SAFE AREA: - 3.0Mtr x 1.7Mtr. Chest press equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100NB made up of “B” Class G.I. pipe. The bottom welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes are made up from 25NB “B” class G.I. pipe. The handle frame is made up from 32NB “B” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap is made from FRP Material with 0.7 thickness. Pins used of Diameter 25mm and 17mm are made up from bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly.The cerclips used for locking is made up of A24 mm & A16mm. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.

Providing & Fixing imported Stainless steel grade 304 for fencing & Gate. (L.S)

Providing and fixing spiral slide (Roto molded):- Roto molded spiral slides is in one piece rotationally molded is made of L.L.D.P.E. and has a double layer (both side finish) having thickness of 4mm. resting on vertical poles of 80mm nominal bore, G.I. pipe ttached to platform with the help of 2 no.'s 50mm NB GI pipe on height of 2400mm, platform made of 2mm thick precision punched hole GI sheet and railing to platform made of 25mm & 20mm nominal bore G.I pipe, Entry Ladder made of 25mm & railing of ladder is made up of 25 mm nominal bore GI pipes and jointed with help of 16 swg GI sheet triangular steps having width 500mm, 90mm tread & maximum 225mm riser. All parts to be powder coated with minimum thickness of 40 microns uniformly and then fixed in cement concrete blocks of required size and mix etc complete as per drawing / sketch and direction of Engineer –in-charge at the site. (a) Deck height –2400mm.

Corrugated G.I. Sheet roofing 0.80 mm thick fist with G.I."J" or "L" hooks

Precast Chequered Tiles Flooring. Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings In case colour chequered tiles in flooring are used, increase the through rate of Item No. 14.45 by 10%.

SKY WALKER DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height) SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle. The handle frame is of 25mm NB made from “B” Class G.I. pipe.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Aluminum casting material of size 130 X 310 X 5mm. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25mm bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “6205zz” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.

15 mm thick cement plaster 1:2 on the rough side of single or half brick wall

Seated Puller DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3Mtr Seated puller equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100NB made from “B” Class G.I. pipe. Bottom support is of M.S. round plate of Ø 250 mm & 10mm thickness is welded. All linkages are made up of 25NB “B” class G.I. pipe. The handle frame is of 32NB “B” class G.I. pipe. The seat frame is of 32NB “B” class G.I. pipe, To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 1.2 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Foundation cover Closing Cap is made from FRP Material with 0.7 mm Thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm and 17mm are made up from bright material. The bearings used are of “ 6205” and “6203” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A16. The powder coating done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness.

Arch Swing:- made up of GI pipe 65mm N.B . The Arch swing shall have two numbers of inverted “U” shaped M.S pipe of 65mm N.B. with 7’-6” height above natural ground level at 10 feet center to center all overall size of the Arch. Swing shall be 10’ht 7’-6” (ht. Above GL) The vertical inverted “U” shaped member shall be connected with gi pipe of 65mm N.B.at top as per drawing/design. shall be powder coated , consisting of 4 Nos. belt type swing with bearing assembling chain Zinc coated 6mm thick, butt welded , Belt seat made of frp with non skid surface . The swing shall be fixed in CC as per direction and to the entire satisfaction of Engineer in charge.

Cement Concrete 1:8:16 with stone aggregate 40mm nominal size in foundation and plinth.

12 mm thick cement plaster 1:5

Interlocking Paver Block M 35, 60 mm thick

DOME CLIMBER – Dome climber is made up 20mm IDGI pipe of different nos. of pipes of different length namely 12 nos of 42”, 48nos. of 33”, 12 nos. of 37”, 12 nos. of 30”, 18 nos. of 36”, 6 nos. of 28”, 3 nos. of 24” 6 nos. of 32” and 3 nos. of 25” length. The dia of dome should not be less than 12ft and 6ft ht from ground level. All welded joints are well grinded, All parts to be treated chemically and treated with the pure polyester powder coating (oven baked) with minimum thickness of 40 microns done on the pipes extend the life of equipments.all installed in C.C. base as per order by engineer in charge.

FRP Two lane slide Platform of minimum size 1.2 mtr. X 0.75 mtr. and 1.8 mtr. high supported by four numbers of minimum 50 mm IDGI pipe made ,2.5 mm thick special perforated MS sheet duly supported underneath by angles of size 40 X 40 X 4 mm. Platform should be supported by railing made of 25 mm and 20 mm IDGI pipe horizontal as well as vertical members respectively. The vertical member should be at least 0.75 mtr. high and spaced at distance not more than 100 mm. b) Length and overall width of Slide should not be less than 3.3 mtr. and 1.0 mtr. respectively There is 2 nos. of joint less FRP Slide made of minimum 6 mm thick overall ISO GEL with uv stabilized pigment mixed in gel coat with virgin quality 450 grams matt and G.P. resin duly supported by one number support made up of 25 mm IDGI pipe both side finish, connected with platform. Slide should be made in a single mould piece there is no any joint in the slide. c) Leg support of the platform should be made by 4 numbers of 50 mm IDGI pipe) Two numbers of Ladder each having width of minimum 50 cm should be made by two numbers of 32mm IDGI pipe having step of minimum size 100 mm tread and maximum 175 mm riser duly supported by 20mm IDGI pipe made of 16 SWG GI Sheet jointed with triangular steps. e) The ladders railing should be made up of 25mm and 20 mm IDGI pipe horizontal as well as vertical members respectively. The vertical member should be spaced as per requirement and safety in such a way that a ladder itself has safety railings for the platform. f) All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. g) All parts to be treated chemically and treated with the pure polyester powder coating (oven baked) with minimum thickness of 40 microns done on the pipes extend the life of equipments. To be installed in C.C. base as per order by engineer in charge.

Applying priming coat with metal primer on new steel or iron work including preparation of surface. Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade.

SEATING & STANDING TWISTER DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). SAFE AREA: - 3 Mtr x 1Mtr. Seating & Standing Twister equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The Center Pipe is of 100mm NB made from “B” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom Handle sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “B” class G.I. pipe. The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “B” class G.I. pipe of 25mm NB. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate fitted on the bottom frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The Pins used are made up of Ø 35 mm bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The powder coating is done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness.

Conglomerate floor 40 mm thick cement concrete topping 1:2:4

Supplying M.S. Bolts of required sizes with nuts and washers complete

C.C. 1:8:16 F/P

First class brickwork laid in cement sand mortar 1:5 in first storey upto 4 meters above plinth level.

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres

Brick-on-edge flooring laid in cement sand mortar 1:4 on 75 mm thick cement 1:8:16 and 100 mm sand filling and cement pointed 1:2 on top.

Earth filling 08Km.

SIT UP BOARD DOUBLE DIMENSIONS: - 1760mm (Length) x 1140mm (Width) x 660mm (Height). SAFE WORKOUT AREA: - 2500mm (Length) x 1600mm (Width). The Sit up Board double made from “B” Class GI pipe. Center column made from 100mm NB “B” class G.I. Pipe. The main frame is of 25mm NB made from “B” Class GI pipe. FRP sheet of 3mm thickness is molded on main frame.The remaining frame of the sit up board is of 32mm NB made from “B” class GI pipe. The powder coating is done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.

SHOULDER BUILDER DIMENSIONS: - 900mm (Length) x 900mm (Width) x 1580mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Shoulder Builder Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeter. The Center Pipe is of 100mmNB made from “B” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness. The handle movement frame is of 25mm NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB”B”or “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 1.2 mm thickness and 20mm x 40mm CRC square pipe of 1.2mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25 mm of bright material. The bearing used is “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A 24. The nylon bush is used for handle knob.The powder coating done with Pure Polyester powder of Ackzonoble or Berger Paints with 60 to70 micron thick.

Design, Manufactue, Providing & Fixing of all in one Solar Street Light 15W with Luthium Ferro Phosphate Battery & 75mm Dia GI 6Mtr. Long Pole with 5 year Warranty of Complete system in different Location in Municipal Council Bahadurgarh.

HORSE RIDER DIMENSIONS: - 1180mm (Length) x 400mm (Width) x 1400mm. (Height). SAFE AREA: - 2.2Mtr x 1.4Mtr. Horse rider equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame of 100NB made from “B” Class G.I. pipes welded with M.S. round plate of Ø250 mm & 10mm thick Seat provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 1.2 mm thickness and 20mm x 40mm CRC square pipes of 1.2mm thickness. The leg movement frame is of 32NB made from “B” G.I. pipe. The handle frame is of 32 NB made from “B” Class G.I. pipe. The footrests are made from 25 NB “B” class G.I. pipe. Pins used of Diameter 17 mm are made up from bright material. The bearings used are “6203 ZZ” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The circlips used for assembly are of A24 mm. The powder coating done with Pure Polyester powders of Ackzonoble or Berger with 60 to 70 micron thickness.

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position.

Providing & Laying of Grass Carpet complete in all respects.