Public Works Department Tender

Providing and installing in specified position Table with Drawers of size 600 mm (Wide) x 1200 mm (Length) x 800 mm (Ht.) Top of the table should be Using 19mm approved make Boiling water proof marine ply (BWP), 4.0 mm thick Vineer finish melamine polish all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick laminate melamine polish on all sides of plywood areas of approved color. Table Top to be fitted with 10mm Clear glass. Table shall have Supported by Storage and Gable end . Gable end shall be made of 19 mm thk BWP plywood with 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color. Another side of Storage shall be Combination of 1 Drawer and Open shelf (Space for CPU). Drawer shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching. Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching. Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. Item shall be complete as per the approved drawing of Table - T1 and as direction of Engineer – in - charge.The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T1.

Providing and installing in specified position Table with Drawers of size 750 mm (Wide) x 1500 mm (Length) x 800 mm (Ht.) Top of the table should be using 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color . Table Top to be fitted with 10mm Clear glass. Table shall have Supported by Storage from Both Side, One Side of Storage (1 Drawer and 1 Shutter) shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Drawer in Storage Panel Shall be made of 12 mm thick Marine Plywwod with 4.0 mm thick Vineer finish melamine polish and edge Banding. Another side of Storage shall be Combination of 1 Drawer and Open shelf (Space for CPU). Drawer shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching. Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. Item shall be complete as per the approved drawing of Table - T2 and as direction of Engineer – in - charge.The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T2.

Providing and installing in specified position Table with Drawers of size 900 mm (Wide) x 1800 mm (Length) x 800 mm (Ht.) Top shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color . Top shall have Curver from front end with 1/2 round teak wood beading on all edges 10cm and melamine finish. Table Top to be fitted with 10mm Clear glass. Table shall have Supported by Storage from Both Side, One Side of Storage (1 Drawer and 1 Shutter) shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Drawer is Storage Panel Shall be made of 12 mm thick Marine Plywwod with 4.0 mm thick T.W.Vineer finish and edge Banding. Another side of Storage shall be Open shelf (Space for CPU). Shelf shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Vineer finish on all sides of plywood areas of approved color with 1mm lipping of matching., Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Vineer finish on all sides of plywood areas of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. Item shall be complete as per the approved drawing of Table - T3 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T3.

Providing and installing in specified position Side Storage Table of size 500 mm (Wide) x 1000 mm (Length) x 750 mm (Ht.) Top shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges, including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick Veneer finish on all sides of plywood areas of approved color . Table Top to be fitted with 10mm Clear glass. Storage shall be combination of Drawer, Shutter and Openable shelf. Storage Drawer and Shutter shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Drawer is Storage Panel Shall be made of 12 mm thick Marine Plywwod with 4.0 mm thick Veneer finish and edge Banding. Storage shall have Shelf and Shelf shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching. . The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Item shall be complete as per the approved drawing of Table - T3 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T3(Side storage table).

Providing and installing in specified position Table with Drawers of size 900 mm (Wide) x 1800 mm (Length) x 800 mm (Ht.) Top shall be made of 19mm approved make Boiling water proof marine ply 4.0 mm thick Veneer melamine finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick Veneer finish on all sides of plywood areas of approved color. Table Top to be fitted with 10mm Clear glass.Table shall have Supported by Storage from Both Side, One Side of Storage (1 Drawer and 1 Shutter) shall be made of 19mm approved make Boiling water proof marine ply (BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Drawer is Storage Panel Shall be made of 12 mm thick Marine Plywwod with Veneer finish and edge Banding. Another side of Storage shall be Combination of 1 Drawer and Openable shelf (Space for CPU). Drawer shall be made of 12mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching.Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish on all sides of plywood areas of approved color. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Item shall be complete as per the approved drawing of Table - T3a and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T3a.

Providing and installing in specified position Wooden Table of size 900 mm (Wide) x 2200 mm (Length) x 800 mm (Ht.) Top shall be made of 30mm 1st class teak wood with beading of 100mm x 40mm of 1st class Teak wood on all side of the top with vineer polish. The table should be supported on teak wood runners placed on 4 legs of 1st class teak wood of size 3" x 3" partly square and partly rounded. The table is fitted together using necessary hardware . Item shall be complete as per the approved drawing of Table - T4 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T4.

Providing and installing in specified position Table of size 1800 mm (Wide) x 3600 mm (Length) x 750 mm (Ht.) Top shall be made of Black granite with full rounded edges. Table shall have Supported by 2 nos Storage and 9 nos open shelves. 2 nos Storage unit with doors shall be made of 19mm approved make Boiling water proof marine ply (BWP), 4.0 mm thick Veneer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided.Open shelf unit shall be made of 19mm approved make Boiling water proof marine ply (BWP), 4.0 mm thick Veneer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided with a 12mm water proof marine ply horizontal shelf 4.0 mm thick Veneer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. The Centre of the table should have Keyboard tray, storage for CPU and Footrest made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Item shall be complete as per the approved drawing of Table - T6 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T6.

Providing and installing in specified position Side Storage Table of size 800 mm (Wide) x 3000 mm (Length) x 800 mm (Ht.) Top shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color . Table Top to be fitted with 10mm Clear glass. Storage shall be combination of 3 nos Drawers on either side and Open shelf for CPU. Drawers shall be made of 12mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Open shelf (Space for CPU) shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Vineer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W.Vineer finish on all sides of plywood areas of approved color. The table to be fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Item shall be complete as per the approved drawing of Table - T5 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T5.

Providing and installing in specified position Wooden Video Conference Table of flattened U shape of size 1430 mm (Wide) x 4250 mm (Length) x 800 mm (Ht.) Top shall be made of 30mm 1st class teak wood with beading of 100mm x 40mm of 1st class Teak wood on all side of the top with vineer polish and 10mm clear glass on top. The table should be supported on teak wood runners of heigth 80mm placed on 10 legs of 1st class teak wood of size 3" x 3" partly square and partly rounded. The table is fitted together using necessary hardware . Item shall be complete as per the approved drawing of Table - T7 and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- T7.

Providing and installing in specified position Table with Drawers and storage unit of size 600 mm (Wide) x 1500 mm (Length) x 800 mm (Ht.) Top of the table should be using 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges . including modesty panel of size 19 mm thk BWP plywood with 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color. Table shall have Supported by Storage (1 Drawer and 1 Shutter) shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges shall be provided. Drawer in Storage Panel Shall be made of 12 mm thick Marine Plywwod with 4.0 mm thick Vineer finish melamine polish and edge Banding. Additionally the table should include Combination of 1 Drawer and Open shelf (Space for CPU). Drawer shall be made of 12mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching. Keyboard tray shall be made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish on all sides of plywood areas of approved color with 1mm lipping of matching. Footrest shall made of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Vineer finish melamine polish on all sides of plywood areas of approved color. The table is fitted together using necessary hardware such as Chip Board Screws, dowels, drawer slides, handles,Wire manager and locks etc. Inner sides of the table to be laminated with 1.00mm laminate and outer sides to be provided with veneer melamine polish of approved color. Item shall be complete as per the approved drawing of Table - WS-1 and as direction of Engineer – in - charge.The rate shall be inclusive of Labour, tools and transportation, etc complete. Refer enclosed Drawing of Table- WS-1.

Providing and installing in specified position Cafetaria Table of size 900 mm (Wide) x 1500 mm (Length) x 750 mm (Ht.) Top made of raw material HDPE supported of high gloss powder coated metal framework of approved color and design and as direction of Engineer – in - charge.The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing and installing in specified position Wooden Table of size 600 mm (Wide) x 2200 mm (Length) x 800 mm (Ht.) Top shall be made of 30mm 1st class teak wood with beading of 100mm x 40mm of 1st class Teak wood on all side of the top with vineer polish. The table should be supported on teak wood runners placed on 4 legs of 1st class teak wood of size 3" x 3" partly square and partly rounded. The table is fitted together using necessary hardware . Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position Wooden  Revolving Chair, Overall Dimension: 710W ±10 x 710D ±10 x 1200H ±10 mm, Chair  Seat , Back and Arm made up in solid wood , Complete  structure are in Melamine polish, Used PU foam on Seat & back  of D-32 kg/m3  with prime Quality fabric,  Seat Size: 580W ±10  x 510D ±10 x 60Thick. ±5 mm, Back Size: 500W ±10  x 680H ±10 , Mechanism:- Torsion Bar Single point control , Provides maximum adjustability and scope for comfort , Seat & Back moves in same direction , Single/ Upright position locking , Tilt tension knob to loosen or tighten the tension according to users body weight, Gaslift:- Lift -Used gaslift of 85 mm size of Class-IV grade , Plastic Gas lift cover. Chair Base & Wheels:- Chair Base made of Wooden cladded top on MS base powder coated frame with plastic cover on it, base consists of 5 prongs with 660 ±5 mm pitch circle diameter , 50 mm Dia. Black Nylon -Twin Wheel Pin castor. The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and Green Co, BIFMA Level 3 Certificate, Green Guard Compliance, AIOTA Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position High Back Executive Chair - The seat shall be made up 12mm thick Ply Board and Back shall made up of 18 mm ply. Seat and Back shall Covered with pure leather (0.9 mm) on seating part & moulded with High Resilience (HR) PU foam. The Thickness of Seat Cushion shall be 52 mm and back cushion shall be 50 mm thick. Chair shall have the adjustable type armrest with the 3D function (Up/Down, Swivel, Front/Back). The armrest top shall be moulded from PU Pad and mounted on to a drop lift to armrest support & shall have 1 steps height adjustment of 40-50 mm. Chair shall have Bio synchro mechanism with 4 Position Locking , 360 degree revolving type, seat back tilting ratio 1:2, 4 position tilt limiter. Chair shall have Gas lift with the height adjustment of 100 mm. The Size of Seat shall be 52.5Wx50.5 D in cm and back size shall be 52.5Wx82.0cm Ht. The chair shall have high Chrome finished aluminium pedestal of size 700 mm pitch centre dia. fitted with 5 Nos. Twin PU Wheel Castors with Size of 60 mm dia. castors. Overall Seat Height - 44.0- 54.0cm. Height - 116.0-126.0cm. Width-70.0 cm and Depth-69.0 cm. The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and Green Co, BIFMA Level 3 Certificate, Green Guard Compliance, AIOTA Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position High Back Executive revolving office chair with the specification -Chair shall have mesh in back and High-quality PU foam cushion in the Seat upholstered with high quality of Fabric. Chair shall have adjustable arm rest with adjustment up to 60 mm. Arm shall made of Polypropylene and Chair shall have PU Pad armrest with 3-Dimensional Movement (Up-Down, Left and Right). Chair shall have adjustable lumber support to adjust the back for extra comfort. The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with Fabric. Lumbar pad has an adjustment of 30 mm in height with adjustable tilting mechanism is designed with the following features.360-degree revolving type. Chair shall have Advance Bio synchro mechanism with 3 position locking facility at difference level. Seat shall made of 12mm thick hot-pressed ply covered with high density moulded foam with the thickness of 50 mm and seat shall be upholstered with High Quality of fabric and back shall come with high quality of Mesh. Chair shall have headrest covered with Fabric with pivot adjustment. The size of seat and back are, back size- 480Wmm x 660Hmm and Seat size 470Wmm x 490Dmm.Chair shall have gas lift and height adjustment up to 120 mm. Chair shall have twin wheel castor star base of PCD Ø 700. Casters Ø50mm made of Nylon and should be 5nos castor. Overall Dimension - 700 W x 730 D x 1190/1310H Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position Visitor Executive Chair - The seat shall be made up 12mm thick Molded Ply Board and Back shall made up of 18 mm Molded ply. Seat and Back shall Covered with pure leather (0.9 mm) on seating part & moulded with High Resilience (HR) PU foam. The Thickness of Seat Cushion shall be 52 mm and back cushion shall be 50 mm thick. Chair shall have fixed arm and arm Armrest shall be made of Aluminium with PU Cushion on top. Chair shall have Chrome finish Cantilever under structure of size Dia. 25.4x2 mm thick CRCA sheet. The Size of seat shall be 52.0 W cm x50.5 D cm and Back Size shall be 52.0 W cm x58.0 D Cm (Eff.) The Seating Height of Seat shall be 45.0cm and Overall, Height - 10.50cm.The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and Green Co, BIFMA Level 3 Certificate, Green Guard Compliance, AIOTA Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position Visitor office chair with the specification - Chair shall have mesh in back and High -quality PU foam cushion in the Seat upholstered with high quality of Fabric. Chair Arm shall made of Polypropylene and Chair shall have PP Fixed armrest. Chair shall have adjustable lumber support to adjust the back for extra comfort. The lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with Fabric. Lumbar pad has an adjustment of 30 mm in height with adjustable tilting mechanism is designed with the following features. Chair shall have Cantilever under structure of size Dia . 22x3 mm thick CRCA sheet confirming GADE D. Seat shall made of 12mm thick hot -pressed ply covered with high density moulded foam with the density of 45 -50Kg/Cu M with the thickness of 50 mm and seat shall be upholstered with High Quality of Fabric and back shall come with high quality of Mesh. The size of seat and back are, back size -480Wmmx660Hmm and Seat size - 470Wmmx490Dmm. The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and Green Co, BIFMA Level 3 Certificate, Green Guard Compliance, AIOTA Certificate. Overall Dimension - 600 W x 605 D x 1020 Ht. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position Chair with the specification- The seat and back are made of injection moulded high impact strength polypropylene polymer compound. The Seat shall be Padded with Cushion with the thickness of 25 mm and with the density of 40-45 Kg/Cu.M. Back of Chair shall have Curve and perforation for the better back support and air ventilation. The Size of Injection moulded seat shall be 464Wx424D and Back size shall be 464Wx400 Ht. Chair shall have welded Structure. Chair shall have Fixed PU Padded Armrest with the Size of 228Lx68D. Chair shall have 4 Legs for better stability with the Size of 30x15x1.2 mm thick. Chair structure shall be made of MS ERW tube (Oblong Section). All the Metal Parts shall be Powder Coated with the minimum 50-80 micron. Chair shall have tested various Load as per BIFMA Norms like Seat Test, Back Test, Arm Test. Chair shall have Nylon Plastic Cap to avoid the scratches on Ground. Overall Dimension- 580W x 565Dx 800 Ht. (Dimension in MM). Manufacturer Certification: The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and CII Certified Green Co, BIFMA Level 3 Certificate, Green Guard Compliance Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position Cafetaria Chair as per below Specifications- Seat and Back Material: The seat and back of the chair shall be made of single injection molded high impact strength polypropene polymer compound with indoor-grade UV resistance.Seat Shape and Size: The seat shall have a rectangular shape, and the minimum size of the seat shall be 450 mm x 430 mm. Under Structure: The chair shall have an under structure made of stainless steel of SS 202 grade. Load Capacity: The chair shall have a minimum load capacity of 150 kg. Legs: The chair shall have four legs, and the size of each leg shall be a minimum diameter of 25.4 mm with a thickness of 1.2 mm. Foot Caps: Heavy-duty foot caps shall be provided below the legs of the chair. Testing: The chair shall be tested according to BIFMA standards, including base static test, seat fatigue test, static load test, etc. Multicolor Options: The chair shall be available in multiple color options.Overall Dimension: The overall dimensions of the dining chair shall be 450 mm width x 587 mm depth x 805 mm height.The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and CII Certified Green Co, BIFMA Level 3 Certificate, Green Guard Compliance Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing, installing and placing in position 3 Seater Waiting Chair with the specification- MAIN FRAME-The chair shall be on main frame of High Quality CRCA Steel of minimum thickness 1.2 mm and appropriate cross section so as to achieve the required strength and durability as per latest BIFMA (Business Institutional Furniture Manufacturers Association) X 5.4 - 2020 standard with powder coating of minimum 70 microns. The ends shall be aesthetically designed and plugged with end caps SEAT & BACKREST-The seat & backrest shall be of integral type made from high density self-skinned integral PU foam coloured in the mass reinforced with concealed steel frame of maximum 60 mm width with following options, and thickness so as to achieve the durability as per latest BIFMA X 5.4 standard: PU with steel springs integrated in concealed steel frame. The profile of the integral system should ensure comfortable sitting having ergonomic profile and thigh support. The seat should have slant towards backwards for comfort. The thickness, hardness and density of the PU moulded foam seat should guarantee satisfactory level of comfort for the user. The density should be minimum 350 Kg/m3. The shore ‘A’ hardness should be between 45 to 85.Seat and Backrest may either be one single unit or separate seat and back in two separate units. The seat and backrest should comply with the fire-retardant norms BS 5852 Crib 5 (which describes best practice methods to assess the ignitability of single material combinations) test method or EN 1021:1, EN 1021:2 (Assessment of the ignitability of upholstered furniture) or equivalent Indian Standard.Seat and backrest shall be fixed on the main frame conveniently ensuring screws, nuts and bolts are not directly intruded in the PU of Seat and Back but fitted in metal parts BASE / LEGS-The frame support (Base / legs) shall be of high pressure aluminium die cast. The base / legs shall be finished with powder coating of minimum 70 microns. The design of the base/legs shall ensure that the chair remains stable and it should have suitable anti-skid level adjusting shoes of soft grip at the bottom. The design of the base/ legs and its fixing shall be such that it achieves the durability as per latest BIFMA X5.4 standard ARMREST-Armrests for each seat made of high-pressure aluminium die cast shall be provided. The armrests should be finished with powder coating of minimum 70 microns. The armrest and its fixing shall be stable enough to achieve the durability as per latest BIFMA X5.4 standard Seat Size-520Wx465D and Seat Height 430 mm. Overall Dimension-1630Wx650Dx850 Ht (in MM)The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and CII Certified Green Co, BIFMA Level 3 Certificate, Green Guard Compliance Certificate. Item shall be complete as per the approved design and as direction of Engineer – in - charge. The rate shall be inclusive of Labour, tools and transportation, etc complete.

Providing and installing in specified position Cupboard of 470mm depth x 1090mm x 2100mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. 3nos Horizontal Shelves of cupboard are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of cupboard.Inner sides to be laminated in white shade. Rate will include for all neccessary hardware such as 6" crome plated handles, hinges, lock, nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table T5 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table- T5.

Providing and installing in specified position two shutter Storage unit of 800mm depth x 900mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. Horizontal Shelf and bottom of unit are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of unit. Inner sides to be laminated in white shade. Rate will include for all neccessary hardware such as 5" steel handles, lock, hinges, nails, screw, adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table T5 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table- T5.

Providing and installing in specified position Open shelf unit of 800mm depth x 900mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. Horizontal Shelf and bottom member of unit are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of unit. Rate will include for all neccessary hardware such as nails, screw, adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table T5 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table- T5.

Providing and installing in specified position series of wall mounted Cupboard of 470mm depth x 2500mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. 5nos Horizontal Shelves, top member and bottom member of cupboard are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of cupboard. Inner sides to be laminated in white shade. Rate will include for all neccessary hardware such as 8" steel handles, lock nails, hinges, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Cupboard in court hall and as direction of Engineer – in - charge. Refer enclosed Drawing of Cupboard in court hall.

Providing and installing in specified position Cupboard of 500mm depth x 2100mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. 5nos Horizontal Shelves, top member and bottom member of cupboard are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of cupboard. Inner sides to be laminated in white shade.Rate will include for all neccessary hardware such as 8" steel handles, lock nails screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Cupboard in court hall and as direction of Engineer – in - charge. Refer enclosed Drawing of Cupboard in court hall.

Providing and installing in specified position series of locker modules of size 500mm (D) x 2100mm (H) ,each locker should be of sixe 600mm x 600mm made up of CRCA (Cold rolled close annealed) perforated Sheet not less than 0.8mm thick for Carcass & Shelves, Skirting to be with 1.2mm thick CRCA Sheet, unit top to be made out of 2mm thick CRCA Sheet and shelve Stiffener to have an overall thickness not less than 15mm. The shelves should have a load carrying capacity of 35kg (UDL- Uniformly distributed load). Each locker to have 08 Lever cam lock with lock lever & ABS recess plastic handle. The storage fitted on base frame MS tube of size SHS 25x25 mm having 2.34 mm thickness. All M.S members shall be conforming to IS-3074 furniture grade. All metal components shall be pre-treated and finished with super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer . The base frame shall be secured using nylon glide /end caps of required size, shape & colour & levelling bolt of nylon/ABS shall be provided to adjust height of frame and legs & to take care of unevenness in floor.Rate shall include of all iron mongeries hardware,fittings,fixtures etc. Item shall be complete as per the approved design of Cupboard in court hall and as direction of Engineer – in - charge.

Providing and installing in specified position Cupboard of 450mm width x 900mm length x 1300mm height made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick Veneer finish melamine polish on all sides of plywood areas of approved color with 1mm lipping of matching / approved color with all exposed edges. 3nos Horizontal Shelves, top and bottom members of cupboard are made up of 12mm thick T.W. Veneer finish and 1mm lipping of matching / approved color with all exposed edges as per drawing & design. Shutter of cupboard made up of 19mm approved make Boiling water proof marine ply(BWP), 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color fix with the help of hinges. 10mm thick plywood is provided at back of cupboard.Inner sides to be laminated in white shade. Rate will include for all neccessary hardware such as 6" crome plated handles, hinges, lock, nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table WS1 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table- WS1.

Providing and installing in specified position Modular Rack unit with the Overall Dimension of 900mm Width x 450mm Depth x 1800mm Heigth. The Entire Storage Unit should be made of 0.8 mm thick CRCA sheet Confirming to Grade D with 60 –70 -micron Powder Coating. The Vatical beam of rack shall made of 40x40x2 mm thick MS Angle as per IS 10748. Each Rack shall have 04 level of Adjustable shelves. The Angle of Rack shall be of rolled formed construction and free from twist, sharp edges and Burrs. Racks shall have Hole towards Height Wise for adjustability of Shelves at different levels. The Stack ability shall be addon units can be stacked width wise to form a bank of racks having Common side panels. Rack shall have adjustable Shelves, which is made of 0.8 mm thick CRCA Sheet in approved shade of Powder Coating. The Uniform Load Bearing capacity of each rack shall be 80 Kg Maximum. Shelf back Stiffener at the rear end of the shelves shall be provided. Label Holder shall be provided at each lever. The manufacturer shall have ISO 9001, 14001, 45001, 50001 accreditations by NABCB only, and Green Co, BIFMA Level 3 Certificate, Green Guard Compliance, AIOTA Certificate Item shall be complete as per the approved design and as direction of Engineer – in - charge.

Providing and installing in specified position 100mm thick partition of 1300mm height made up of teakwood frame of section size 60mm x 60mm at spacing of 600mm c/c bothways made of 19mm approved make Boiling water proof marine ply(BWP) with 4mm thick plywood for groove fix on both side of frame and 4.0 mm thick T.W. Veneer finish melamine polish on all sides of plywood areas of approved color including melamine polish having 4mm deep grooves on either side of the partition. Top of partition provided with 75mm thick teakwood beading duly melamine polished. Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table WS-1 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table- WS-1.

Providing and installing in specified position 100mm thick partition of 900mm height made up of teakwood frame of section size 60mm x 60mm at spacing of 600mm c/c bothways made of 19mm approved make Boiling water proof marine ply(BWP) with 4mm thick plywood for groove fix on both side of frame and 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Top of partition provided with 75mm thick teakwood beading duly melamine polished. 19mm plywood on the front side of the plywood to be extended additional for a depth of 450mm to cover the raised portion of the slab with 4mm thick plywood for groove fix on both side of frame and 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table T6 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table-T5.

Providing and installing in specified position 100mm thick partition of 1100mm height made up of teakwood frame of section size 60mm x 60mm at spacing of 600mm c/c bothways made of 19mm approved make Boiling water proof marine ply(BWP) with 4mm thick plywood for groove fix on both side of frame and 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Top of partition is provided with platform extending 150mm on either side made of 19mm approved make Boiling water proof marine ply(BWP) with 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) . Top of the platform to be provided with 10mm clear glass 300mm heigth supported on 50mm x 50mm teak wood member and provided with voids at specified locations. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Table T6 and as direction of Engineer – in - charge. Refer enclosed Drawing of Table-T6.

Providing and installing in specified position 100mm thick full heigth partition (part wooden and part glass) made up of teakwood frame of section size 60mm x 60mm at spacing of 600mm c/c bothways made of 19mm approved make Boiling water proof marine ply(BWP) with 4mm thick plywood for groove fix on both side of frame and 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Top portion of the partition is 5mm clear glass 480mm heigth supported on 100mm x 50mm teak wood member above 10mm clear glass 480mm heigth supported on 100mm x 50mm teak wood member. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish having 4mm deep grooves on either side of the partition. Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design for partition of Judicial Service counter & room for registry and as direction of Engineer – in - charge. Refer enclosed Drawing for partition of Judicial Service counter & room for registry.

Providing and installing in specified position 100mm thick partition of 750mm height made up of teakwood frame of section size 60mm x 60mm at spacing of 600mm c/c bothways made of 19mm approved make Boiling water proof marine ply(BWP) 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish. Top of partition provided with 75mm thick teakwood beading duly melamine polished. Front side of the Partition should have openings of 850mm x 470mm at specified locations. Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of Accused bay and as direction of Engineer – in - charge. Refer enclosed Drawing of Accused bay.

Providing and installing in specified position Witness box of overall size 1300mm x 1160mm x 1300mm with opening of 1000mm and raised floor of 150mm. Witness Box made up of 19mm approved make Boiling water proof marine ply(BWP) supported on teak wood frames with sections of 200mm x 100mm at all corners finished with 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade) including melamine polish. Witness box is provided with ramp of size 1500mm x 1000mm made up of 19mm approved make Boiling water proof marine ply(BWP) with proper support finished with 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade). Hand rail to be provided with section of size 50mm x 60mm & End post sections of size 50mm x 50mm with intermediate sections of 40mm dia at 100mm c/c spacing. 150mm raised box frame made up of teakwood section & 19mm plywood fix over Teak wood frame & finished 4.0 mm thick T.W. Veneer finish on all sides of plywood areas of approved color (wood shade). Rate will include for all neccessary hardware such as nails, screw adhesive, labour, tools and transportation etc. Item shall be complete as per the approved design of and as direction of Engineer – in - charge. Refer enclosed Drawing of Witness Box.

Providing and installing in specified position roller blinds durable for large span of approved make, of varying length, height, approved colour, shade of fabric, aluminum extruded rail with matching powder coated colour. Made with universal clutch for left or right hand operation; tube with natural anodized finish, Clutch to be fixed to brackets. Including Die Cast brackets with plastic covers with white end cap, UV Protected high strength reinforced Plastics components & flat extruded valance with white powder coat finish, including all necessary fittings and fixtures like idler, head rail, control unit, roller tube, bottom rail, operating chain, fixing brackets, clamps, screws, etc. Fabric of the Blind: Composition: 39 to 45% Polyester / 50 to 61% PVC with Aluminium Backing. Weight: 270 to 290 g/m2 (+/-5%). Thickness: 0.32 mm (+/-5%). Fabric Openess Factor: 3% Visible Light Transmission: 2% - 4% (N-N). Solar Transmission : 3%-13%. Solar Reflectance: 9%-65%. Solar Absorption: 22%-88% . Tensile Strength (Warp/Weft): 160/170 daN/5cm. Tearing Strength (Warp/Weft): 11/13 daN Fungistatic Treatment: Degree 0, Excellent (EN ISO 846-A) Fire Retardancy: B-s2, d0/EN 13501-1, CLASS A/ASTM E84. Greenguard Gold Certificate. All material shall be of approved make, in proper line, level, colour, finish etc. complete as per the drawing, specification and directions of Engineer – in - charge.

Providing and installing in specified position 50mm Wood Blinds of approved make with ladder tape Easyrise operating System: Country Wood Blinds of classic wood range suitable for hot and humid weather with UV finish wooden components with high quality test for color fastness and low VOC. Technical Specification:Thickness: 3mm; Fire Retardant: NFPA 702 (on demand) Slat Size: 50mm, String Tape: 2.5mm, 100% Polyester Valance: 70mm. To include components like Ladder Tape, Cord Tilter, 0.5mm thick Aluminum Head Rail, and all neccessary supporting components complete. All material shall be of approved make, in proper line, level, colour, finish etc. complete as per the drawing, specification and direction of the Engineer.

Providing and installing in specified position Signage made up of base material of 6mm thick transparent/ coloured acrylic sheet. The graphic is of computer cut self adhesive vinyl covered with clear vinyl to protect from peeling. The signage shall be fixed with 12mm dia SS 304 grade studs or SS 304 grade mirror screws. All material shall be of approved make. All works shall be completed as per the drawing, specification and direction of the Engineer in Charge.

Providing and installing in specified position Signage made up of base material of 6mm thick transparent/ coloured acrylic sheet. The graphic is of 3mm laser cut acrylic letters in specified colours on single sides using suitable adhesivor self. The signage shall be fixed with self adhesive glue tape. All material shall be of approved make. All works shall be completed as per the drawing, specification and direction of the Engineer in Charge.

Providing and installing in specified position Braille Signage Crafted from SS304 grade stainless steel. The signage shall be fixed with 12mm dia SS 304 grade studs or SS 304 grade mirror screws. All material shall be of approved make. All works shall be completed as per the drawing, specification and direction of the Engineer in Charge.

Providing and installing in specified position signages from aluminium composite panel of size as per detail dwg. & color as approved by the Engineer with vinyl pasted lacquering of letters varying colors as approved by the Engineer and as per specifications. Panel will then be fixed on the wall with SS studs, clear washable dustproof coat, etc. arrangement as per drawings. All material shall be of approved make, in proper line, level, color, finish etc. complete as per drawing, specification and direction of Engineer in charge.

Providing and installing in specified position SS 202 grade Queue Manager of pole size 63mm x 900mm lenth x 0.8mm thick with base 300mm dia at 7kg base weight with filling material cast iron . The belt size 50mm width and 3m length in Red/Blue/Green/black or yellow colors. The queue manager having four way mechanis and lock system. of approved make/color as per the specifications and directions of Engineer in charge.

Providing and installing in specified position Floor Mounted Bottled water dispenser with cooling cabinet of approved make (latest model) having function of dispense Hot/cold/ Ambient water, with LED display and having Refrigerated capacity of 15litres, with voltage/frequency/phase of 230V/50Hz/single. The cold tank should be of SS304 food grade,having storage capacity of 3.2lit with cooling capacity of 2.5lts/hr at 12°C Discharge. Having Power consumption of 120W, heating Capacity 5lit/hr at 85° C discharge and power consumption 500W heating, having faucet push type/child lock for hot tap. Dimension (WXDXH)mm 310X345X940mm. Net weight 16.5kg. of approved make (latest model)/color/ design as per the specifications and directions of Engineer in charge.

Providing and installing in specified position MIC STAND with overall size 250/100 mm (W) x 250/100 mm (D) x 350 mm (H) made up using 12mm Thick BWP Marine grade plywood conforming to IS : 710 Exterior Grade of approved make, 4.00mm Veneer on external & inner surfaces, as per drawings with 2nd class teak wood beading patti including one or more coats of Melamine glossy polishing for matching approved colour on all underside and unlaminated areas. Rate shall include of all hardware, fittings, fixtures etc. All material shall be of approved make. All works shall be completed as per the drawing/image and as per the specifications and directions of Engineer in charge.

Providing and supplying Three Seater Sofa made of hardwood frame with armrest on either side having vertical spring filled with thick nylon thread for seat & back cushion having 3" thick u Foam for back & 4" thick for seat with full upholostery complete etc as per the directions of the Engineer in charge. Basic rate of Cloth Rs.660/- Per Mtr.

Providing and supplying Single Seater Sofa made of hardwood frame with armrest on either side having vertical spring filled with thick nylon thread for seat & back having 3" thick u Foam for back cushion & 4" thick for seat cushion with full upholostery complete etc as per the directions of the Engineer in charge. Basic rate of Cloth Rs.660/- Per Mtr

Providing and supplying Coffee Table with Glass Top 1200m x 900mm top made of teakwood Frame work having 8mm thick clear glass with beveling for top with teakwood legs finished in melamine polish finish complete etc as per the directions of the Engineer in charge.

Providing dry wall partition of 6mm plywood laminated of approved colour using rockwool 64 kg/m3 density, 3mm MLV soundproofing membrane and 9mm polyster board, all material of approved brands and complete as directed by the Engineer in charge.The rate shall be inclusive of Labour, tools and transportation, etc complete.