Tenders of South Central Railway

Parking Lot For Two Wheelers And Four Wheelers In Circulating Area At Adoni Railway Station In (division Guntakal)

CATEGORY: Portable Power Generators (Q3)

Cms/rh/gnt_ Medical_ ( Ph No 04052)

Feed Valve "f" Type Complete To Wsf

031325020090 98110159 (01) (hsn Code: 72044900 - Gst 18% On Fcm Basis), Scrap Of Ond. & U/s. 8 Wheeler Wagons ,bcn M1 ,boxnr . Available On Rails. 1. Ser Bcn M1 30078962009 ,2) Cr Bcn M1 30018964308, 3) Ser Boxnr 25079573897, 4) Wr Bcn M1 30088960484, 5) Cr Bcn M1 30018961574 . Location Road No.3. At Dump Yard. Rc Items: 1.coupler Bodies (nt), 2, Yokes . 3. Knuckles , 4.draft Gears, 5.striker Castings (nt), 6. Centre Pivots 7.wheel Set With Ctrb, 8.casnub Bogies With All Fittings, , 9.yoke Pin Support (1st Plate),10. Safety Plate With Anchor Plate (2n D Plate 11. Yoke Support Plate(3rdplate), 12., Yoke Pin, 13) Draft Gear Followers,14. Knuckle Pin 15. Bcn Swing. . Ds8 No:0999603090 . Dt:07.02.25. Note To Purchaser: Before Delivery Of Wagon Cut Off Parts, The Declared Rc Items Need To Be Handed Over By The Purchaser To Sse/scrap At Shop Floor By Transporting Through Purchaser¿s Vehicle/labor Approx Weight: 68.201 .mt (m.s -64.015 ,ss- 4.186 ) Sold On Number Basis Only Delivery In Cut Up Parts. Note:-if Any Non Ferrous Items Found In Cutting/delivery, Purchaser Should Be Handed Over To Railways. 05 Nos.

Center Pivot Retainer For Casnub Bogie To Rdso Drg.no.wd/85079-s/2, Item-3. Alt.27.

Contract For Operation Of Tea Stall Smu-126 On Platform No.2 Under Cop In Front Of Bo At Charlapalli Railway Station

(ph.no.301950) Vancomycin Antibiotic Discs, 50 Discs/vial, Unit: Numbers.

Uv Stabilised Virgin Hdpe Polymer Extruded Mesh With Hexagonal Aperture Shape Of 28 Mm X 28 Mm As Per Rdso Mi Ti/mi/0050 Rev.1 Along With Technical Clarification Issued By Rdso To Rites Vide Rdso Ltr.no.ti0lko Dt. 12.01.2023 With Following Properties, (1) Grade Of Hdpe Polymer : Virgin (2) Thickness : 2.5 Mm +/-0.5 Mm, (3) Density : 0.94-0.96 G/cm3 (4) Tensile Strength (kn/m) : Minimum Value Of Tensile Strength Should Be 4kn/m (test Certificate From Manufacturer /supplier Should Be Submitted), ( 5 ) Mass : Minimum 510 Gsm (6) Dimensional Tolerances : (i) Aperture Shape :hexagonal (ii) Aperture Size 28mm X 28 Mm (tolerance : 28 Mm + 1mm (ii) Thickness Of Wire Mesh I 2.5 Mm + 0.5mm (7) Melting Point : Minimum Value Is 1300c (both Rdso Mi And Rdso Letter To Rites Referred Above Are Enclosed).

Set Of Items Required For Fiba Modification (items List Enclosed In Annexure) Drg.no.529-3-5-007.