Fiber Tenders

Spain-santiago De Compostela: Communications Network

Details: Description Invitation To Bid For The Procurement Of Hauling Vehicle Delivery Truck (open Cargo) Under Rice Program Fy 2024- Pss 1. The Department Of Agriculture Regional Field Office Iva Through The Rice Program Intends To Apply The Sum Of Two Million One Hundred Thousand Pesos (ᵽ 2,100,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For The Procurement Of Hauling Vehicle Delivery Truck (open Cargo) Under Rice Program Fy 2024 - Pss With Project Identification No.: Itb-2024-12-256. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Department Of Agriculture Regional Field Office Iva Now Invites Bids For The Above Procurement Project. Hauling Vehicle Delivery Truck (open Cargo) A. Prime Mover Type: Diesel Engine Engine Displacement: 1400 Cc, Minimum B. Performance Classification Aspiration Method: Turbocharged And Intercooled Steering System: Power-assisted Steering Transmission System: Constant Mesh-synchromesh (manual) No. Of Drive: Two Emission Rating: Euro Iv, Minimum C. Body No. Of Wheels: Up To Six (6) Wheels Payload: 900 Kg, Minimum Gross Vehicle Weight: 16880 Kg, Maximum Front Cabin : Double Rear Body Type: Open Cargo D. Other Requirements / Inclusion 1. Fuel Tank Capacity: 80 Liters, Minimum 2. Output Power: 190 Ps, Minimum 3. Engine Torque: 450 N-m, Minimum 4. With Fiber Glass Canopy 5. Container Dimension: 5 Ft, Minimum 6. Warranty: 3 Years Or 100,000 Km Whichever Comes First 7. Certification Of Free Labor On Maintenance Service From The First 1,500 Km To 10,000 Km With Consumables Included Within Periodic Maintenance Schedule (pms). 8. Complete Set Of Tools As Per Manufacturer's Specifications, Tint, Seat Cover, Matting (cab), Air-conditioning System, Lto Registration For The First 3-years, Tpl And Comprehensive Insurance, Freight And Da Logo And "for Official Use Only" 9. Radio And Speakers: Tuner Radio With Usb, 2 Speakers 10. With 1 Unit Brand New Spare Tire With Rim And Accessories 11. Provision Of Vehicle Brochure And List Of Service Center In The Bidding Documents 12. With Certificate Of Conformity (coc) Issued By Denr Pursuant To Section 22, Chapter Ii Of Ra 8749 (clean Air Act Of 1999) In Relation To Part Ix, Rule Xxxi Of Denr Administrative Order 2000-81 13. With Certification Of Very Satisfactory Performance Of The Supplier From At Least Three (3) Clients, With Full Address And Telephone Numbers, Within The Last Two (2) Years. 14. With 100% Available Stocks In The Warehouse Of The Bidder During Post-qualification Place Of Delivery: Lares Compound, Brgy. Marawoy, Lipa City, Batangas Delivery Of The Goods Is Required Within Fifteen (15) Calendar Days Upon Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Two (2) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184. A. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From Department Of Agriculture Regional Field Office Iva, 8:00 Am To 3:00 Pm Mondays Thru Fridays Except On The Scheduled Time Of Pre-bid Conference And Inspect The Bidding Documents At The Address Given Below: Department Of Agriculture Regional Field Office Iv-a Bac Secretariat Office / Arturo R. Tanco Training Hall Lipa Agricultural Research And Experiment Station (lares), Brgy. Marawoy, Lipa City, Batangas 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On The Address Given Above Mondays Thru Fridays 8:00 Am To 3:00 Pm Except On The Scheduled Time Of Pre-bid And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos (ᵽ5,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person, Or Through Electronic Means. 6. The Department Of Agriculture Regional Field Office Iva Will Hold A Pre-bid Conference On December 26, 2024 01:00 Pm (bidders Must Be Present At The Venue One (1) Hour Before The Scheduled Bidding Activity. Time Schedule Is Subject To Adjustment Depending On The Flow Of Bidding Activity. Furthermore, Bidders Are Required To Provide Their Company Id And Another Valid Id, And Authorization Letter From The Company They Represent.) At Department Of Agriculture Regional Field Office Iv-a Stiarc Conference Room, Lipa Agricultural Research And Experiment Station (lares), Brgy. Marawoy, Lipa City, Batangas Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below, Department Of Agriculture Regional Field Office Iv-a Stiarc Conference Room, Lipa Agricultural Research And Experiment Station (lares), Brgy. Marawoy, Lipa City, Batangas On Or Before January 7, 2025 9:00 Am. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On January 7, 2025 01:00 Pm (bidders Must Be Present At The Venue One (1) Hour Before The Scheduled Bidding Activity. Time Schedule Is Subject To Adjustment Depending On The Flow Of Bidding Activity) At Department Of Agriculture Regional Field Office Iv-a Stiarc Conference Room, Lipa Agricultural Research And Experiment Station (lares), Brgy. Marawoy, Lipa City, Batangas. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Department Of Agriculture Regional Field Office Iv-a Does Not Condone Any Form Of Solicitation On Any Prospective Winning And Losing Bidders By Any Of Our Staff/employees Or Any Other Party. Any Sort Of This Kind Shall Be Reported Immediately To The Office Of The Secretary Or The National Bureau Of Investigation (nbi) For Entrapment And Proper Investigation 11. The Department Of Agriculture Regional Field Office Iva Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Engr. Ernie N. Rabusa Chairperson, Bids And Awards Committee Secretariat Department Of Agriculture Regional Field Office Iv-a Lipa Agricultural Research And Experiment Station (lares), Brgy. Marawoy, Lipa City, Batangas Contact No.: (02) 8273-24-74 (local 4487) Email Address: Bacsecretariat@calabarzon.da.gov.ph 13. You May Visit The Following Websites: For Downloading Of Bidding Documents: [https://notices.philgeps.gov.ph; Https://calabarzon.da.gov.ph/invitation-to-bid-page/] Date Of Issue: December 17, 2024 ______________________________________ (sgd) Engr. Romelo F. Reyes Chairperson, Bids And Awards Committee

Details: The Work For This Project Includes, But Is Not Limited To, The Construction Of A Multi-story Communications Center Facility To Support Naval Computer And Telecommunications Station Guam Operations. Special Features Include Sensitive Compartmented Information Facility Construction Work In Accordance With Icd/ics 705 And Demolition And Incidental Related Work. Secure Facility Construction Shall Be Performed By U.s. Companies Using U.s. Citizens. the Work Will Also Include Three (3) Pre-priced Options For The Construction Of Two (2) Single-story Warehouse Facilities, And Osp Fiber Line Sonet Ring. In Accordance With Far 52.217-7 Option For Increased Quantity – Separately Priced Line Item, The Government May Exercise The Options By Written Notice To The Contractor Within 365 Days Of Contract Award. the Magnitude Of This Project Is Estimated Between $250,000,000 And $500,000,000. The North American Industry Classification System (naics) Code Is 236220 And Average Annual Receipts Of $45 Million Over The Past Three Years. The Contract Completion Period Is Anticipated To Be 1,255 Calendar Days. a Sources Sought Notice (n62742sscomms) For This Procurement Was Posted On 22 August 2023 On The System For Award Management (sam) Website Https://www.sam.gov/, And A Market Survey Was Conducted That Included An Assessment Of Relevant Qualifications And Capabilities Of Potentially Qualified Firms. As A Result Of The Market Research Analysis, A Determination Was Made To Solicit This Procurement On An Unrestricted Basis Inviting Full And Open Competition. this Solicitation Will Utilize The Tradeoff Source Selection Process. All Technical Factors, When Combined, Are Considered Of Equal Importance To Past Performance. The Factors Are: Factor 1 – Experience, Factor 2 – Safety, Factor 3 – Small Business Utilization And Participation, Factor 4 – Past Performance, And Price. Contract Award Will Be Made To The Offeror Proposing The Best Value To The Government From A Non-price And Price Standpoint. Furthermore, A Relevant Construction Project Is Defined As A Construction Project That Includes At Least One Of The Following Individual Features: (1) Precision Cooling System. New Construction Of A Chiller Type Technology Cooling System Engineered Specifically For Data Center/electronic/it Networking Environments. Projects Submitted Which Reference Comfort Cooling Systems Which Are Engineered Primarily For The Intermittent Use Required To Maintain A Comfortable Environment For People In Facilities Will Not Be Considered. Projects Submitted To Demonstrate Precision Cooling System Will Only Be Considered If The Work Was Performed By The Specific Entity Proposed For The Precision Cooling System Under The Resultant Contract, As Identified In Block 1 Of Attachment A. (2) Uninterruptable Power Supply System. New Construction Of An Uninterruptible Power Supply (ups) System That Is 225 Kva Size Or More. Projects Submitted To Demonstrate Ups System Experience Will Only Be Considered If The Work Was Performed By The Specific Entity Proposed For The Ups System, As Identified In Block 1 Of Attachment A. (3) Clean Agent Fire Suppression System. New Construction Or Replacement Of A Clean Agent Fire Extinguishing System And Releasing System, Including All Mechanical, Controls And Electrical Components Necessary For A Complete And Operating Clean Agent Fire Suppression System. Projects Submitted To Demonstrate Clean Agent Fire Suppression System Experience Will Only Be Considered If The Work Was Performed By The Specific Entity Proposed For The Clean Agent Fire Suppression System, As Identified In Block 1 Of Attachment A. see Request For Proposal (rfp) Document 00 21 16. the Rfp, Including The Specifications And Drawings, Can Be Accessed By Approved Individuals Via The Sam Website At Https://sam.gov/. Approved Individuals Must Register At The Sam Website To Obtain Access To The Rfp. Registration Instructions Can Be Found On The Sam Website. Once Registered In Sam, Approved Individuals Must Request Explicit Access To View The Documents. An Email Will Be Forwarded Once The Contracting Office Has Approved Or Declined The Request. Approved Individuals May View And/or Download The Rfp Documents. Amendments Will Also Be Posted At Https://sam.gov/. It Is Highly Recommended That Firms Register On The Sam Website As This Will Be The Only Plan Holder’s List Available. It Is The Offeror’s Responsibility To Check The Sam Website Periodically For Any Amendments To The Solicitation. offerors Are Required To Be Registered In The Sam Database At Https://www.sam.gov At The Time Of Proposal Submission. see Document 00 21 16 For Pre-proposal Site Visit Information. This Site Visit Is To Provide Offerors With An Opportunity To Familiarize Themselves With The Jobsite And Conditions To Be Encountered And Is Not For The Purpose Of Answering Questions. Forms Submission To Ms. Merbby Corpuz At Merbbyjoyce.n.corpuz.civ@us.navy.mil On Or Before 31 October 2024, 2:00 P.m., Hawaii Standard Time (hst). (1) Current Dbids. If An Interested Attendee Has Current Dbids Credentials For The Specific Base Where The Project Is Located, Submit The Following: company Letter Template: One Letter Required Per Company. List Attendees In Alphabetical Order (by Last Name). Must Be Signed By A Person Authorized To Provide The Certification Required. request For Camera Pass Form: Applicable Only For Those With Dbids Credentials Who Will Be Taking Photos. One Letter Required Per Company. Dbids Number Is Required On The Form. Once Properly Submitted To The Poc In Subparagraph (c) Above And Once Approved, You Will Receive A Routing Number From The Poc. An Appointment With The Naval Base Guam (nbg) Visitor’s Control Center (vcc) Is Required To Complete The Processing Of Your Camera Pass. (2) Current Dbids Not For The Specific Base Where The Project Is Located. Submit The Following: company Letterhead Template: One Letter Required Per Company. List Attendees In Alphabetical Order (by Last Name). Must Be Signed By A Person Authorized To Provide The Certification Required. dbids Base Access Request Form: Each Attendee Please Read, Complete, And Sign/date. Typewritten Is Preferred. Any Handwritten Forms Must Be Legible. email The Vcc At M-gu-nbg-n3at-vcc@fe.navy.mil To Have Their Dbids Programmed With The Specific Base Where The Project Is Located. Prior To Emailing The Vcc, Please Submit The Company Letter And The Dbids Base Access Request Form To The Poc In Subparagraph (c) Above For Approval. Once Approved, The Documents Will Be Sent Back To You For Submission To The Ngb Vcc Along With The Request To Have The Dbids Cards Programmed With The Specific Base Where The Project Is Located. request For Camera Pass Form: Applicable Only For Those With Dbids Credentials Who Will Be Taking Photos. One Letter Required Per Company. Dbids Number Is Required On The Form. Once Properly Submitted To The Poc In Subparagraph (c) Above And Once Approved, You Will Receive A Routing Number From The Poc. An Appointment With The Naval Base Guam (nbg) Visitor’s Control Center (vcc) Is Required To Complete The Processing Of Your Camera Pass. (2) No Dbids Credentials. Submit The Following: company Letterhead Template: One Letter Required Per Company. List Attendees In Alphabetical Order (by Last Name). Must Be Signed By A Person Authorized To Provide The Certification Required. secnav 5512/1 Form: Each Attendee Shall Read, Complete, And Sign/date Form. Typewritten Is Preferred. Any Handwritten Forms Must Be Legible. Do Not Submit The Secnav 5512/1 Form To The Government. The Contractor Is Responsible For Either Hand-carrying Or Emailing This Document To The Ngb Vcc Along With Any Other Pertinent Document Listed In This Subparagraph. dbids Base Access Request Form: Each Attendee Please Read, Complete, And Sign/date. Typewritten Is Preferred. Any Handwritten Forms Must Be Legible. naval Base Guam Foreign National Base Access Request Form (applicable To Foreign Nationals Only). Each Attendee Please Read And Complete. fn Biometric Data Form (applicable To Foreign Nationals Only): Each Attendee Please Read And Complete. request For Camera Pass Form: Applicable Only For Those With Dbids Credentials Who Will Be Taking Photos. One Letter Required Per Company. Once You Have A Routing Number From The Vcc For Your Dbids Application, Insert That Number On The Form. Once Properly Submitted To The Poc In Subparagraph (c) Above And Once Approved, You Will Receive A Routing Number From The Poc. An Appointment With The Naval Base Guam (nbg) Visitor’s Control Center (vcc) Is Required To Complete The Processing Of Your Camera Pass.

Details: The Work For This Project Includes The Construction (design-bid-build) Of A Guam Defense Radar System Command Center (cc), Power Generation Facility, Switchgear Building, Fuel Storage Facility, Entry Control Facility, And Associated Equipment. The Cc Will Include Functional Areas To Accommodate Personnel, Computing Equipment, User Interfaces, And Communications Needed For Planning, Controlling, And Directing Mission Activities. The Power Generation Facility Will Provide Power Via The Switchgear Facility For The Command Center And Associated Infrastructure With Fuel From The Storage Facility Consisting Of Above Ground Fuel Tanks, Fuel Off-loading Infrastructure, And Associated Containment. The Cc Facility And Power Generation Facility Will Be Designed For Risk Category Iv To Meet Site Specific Ground Motion And Seismic Requirements To Include Base Isolation. construction Scope And Methods That Will Be Required As Part Of This Project Include, But Are Not Limited To: demolition Of Existing Housing Units And The Associated Mitigation/disposal Of Asbestos, Lead Contaminated Materials, And Pesticide Contaminated Soil civil Site Work, Including Grading, Paving, And Retaining Walls concrete Construction Meeting The Requirements Of Icc-500 Storm Shelter And Including Coordination Of Cast-in-place, Tilt-up, And Precast Elements 150 Foot Galvanized Steel Antenna Tower And Associated Foundation seismic Isolation Bearings Requiring A Specialized Installation Procedure And Building Erection Sequence Involving Extensive Construction Shoring And Bracing protection Measures For Nonstructural Components, Including Flex Loops For Piping & Conduit To Accommodate Seismic Movement security Infrastructure Includes Real Property Features To Support The Installation Of Security System Level (ssl)-c And Integrated Electronic Security System (iess), Site Security Measures, Entry Control, And Material Procurement & Inspection Requirements facilities Will Be Designed To Provide Cyber Security Engineering And Validation control System Integration Requiring The Aggregation Of Multiple Control Systems, Including Building Controls, Fuel System Controls, And Utility Controls complex Schedule Due To The Nature Of The Concrete & Isolated Foundation Construction, Long Lead Times For Major Equipment Such As Tier 2 Emergency Generators And Mechanical Equipment, And Multiple Joint Occupancy Date (jod) Milestones In The Construction Schedule To Accommodate Work Of Other Contractors Outfitting Systems, Installing Equipment, And Integrating Controls electrical (lighting And Distribution), Fiber Optic And Telecommunications, Fire Protection, Sanitary Sewer, And Storm Drainage the Work Will Include Four (4) Pre-priced Options. Option 1 Is The Price For One Generator And Fuel Tank #2. Option 2 Is The Price For One Generator And Redundancy (b-side Electrical Feeders + B-side Transformer). Option 3 Is The Price For One Generator. Option 4 Is The Price For The Uninterruptible Power Supply In The Command Center. In Accordance With Far 52.217-7 Option For Increased Quantity – Separately Priced Line Item, The Government May Exercise The Options By Written Notice To The Contractor Within 365 Days Of Contract Award. the Magnitude Of This Project Is Estimated Between $250,000,000 And $500,000,000. The North American Industry Classification System (naics) Code Is 236220 And Average Annual Receipts Is $45.0 Million Over The Past Three Years. The Contract Completion Period Is Anticipated To Be 1,323 Calendar Days. a Sources Sought Notice (n62742gdscc) For This Procurement Was Posted On 16 March 2024 On The System For Award Management (sam) Website Https://www.sam.gov/, And A Market Survey Was Conducted That Included An Assessment Of Relevant Qualifications And Capabilities Of Potentially Qualified Firms. As A Result Of The Market Research Analysis, A Determination Was Made To Solicit This Procurement On An Unrestricted Basis Inviting Full And Open Competition. The Navfac Pacific Small Business Office Concurs With This Decision. this Is A Best-value, Trade Off Source Selection Procurement Requiring The Submission Of Both Non-price And Price Proposals. All Technical Factors, When Combined Are Of Equal Importance To Past Performance; And All Evaluation Factors Other Than Price, When Combined, Are Approximately Equal To Price. Proposals Submitted In Response To This Solicitation Shall Be In The English Language And In U.s. Dollars. contract Award Will Be Made To The Responsible Offeror Whose Offer, Conforming To The Solicitation, Is Determined To Be The Lowest Evaluated Price Of Proposals Meeting Or Exceeding The Acceptability Standards For Technical Factors. The Technical Factors Are As Follows: (1) Experience, (2) Small Business Utilization And Participation, (3) Safety, (4) Management Plan, And (5) Past Performance. For Evaluation Of Experience And Past Performance, A Relevant Construction Project Is Defined As: new Construction Of An Administrative, Office Or Communications Facility Approximately $80 Million Or More In Dollar Value And Completed Or Substantially Completed Within The Past Ten (10) Years From The Date Of Issuance Of The Solicitation. new Construction Of A Secure Space Conforming To The Requirements Of Icd-705 Approximately $10 Million Or More In Dollar Value And Completed Or Substantially Completed Within The Past Ten (10) Years From The Date Of The Issuance Of The Solicitation. new Construction Of Essential Facilities Located In Moderate To High Seismic Areas Approximately $80 Million Or More In Dollar Value And Completed Or Substantially Completed Within The Past Ten (10) Years From The Date Of The Issuance Of The Solicitation. the Request For Proposal (rfp) Will Be Available On Or Around 30 October 2024. Printed Copies Of The Rfp Will Not Be Issued. The Rfp, Including The Specifications And Drawings, Can Be Accessed Via The System For Award Management (sam) Website At Https://sam.gov/. Contractors Must Register At The Sam Website To Obtain Access To The Rfp. Registration Instructions Can Be Found On The Sam Website. Amendments Will Also Be Posted At Https://sam.gov/. It Is Highly Recommended That Firms Register On The Sam Website As This Will Be The Only Plan Holder’s List Available. It Is The Offeror’s Responsibility To Check The Sam Website Periodically For Any Amendments To The Solicitation. a One-time Pre-proposal Site Visit Has Been Scheduled For 11 December 2024, 9:00 A.m. Chamorro Standard Time (chst). The Pre-proposal Site Visit Is To Provide Offerors With An Opportunity To Familiarize Themselves With The Jobsite And Conditions To Be Encountered, And It Is Not For The Purpose Of Answering Questions. Offerors Interested In Attending The Site Visit Shall Submit The Following Forms: base Access Request – Contractor Memo (fill-in Information In Red). iii Log (complete In Accordance With The Attached “how To Fill Out The Iii Log” Instructions Located At The End Of This Document.) base Access Affidavit 2020 (completed For Each Visitor That Does Not Have Dbids Pass) foreign National Access Request Form contractor Policy Update Memo either A U.s. Passport Or Real Id Act Driver’s License/id the Completed Forms Shall Be Submitted To Dayna Matsumura, Contract Specialist, At Dayna.n.matsumura.civ@us.navy.mil On Or Before 14 November 2024, 2:00 P.m., Hawaii Standard Time (hst). Once Approved For Base Access, A Tracking Number Will Be Emailed To Attendees For Use When Obtaining Base Passes At The Visitor Control Center (northgate), Andersen Air Force Base. please Be Informed: The Visitor Control Center (northgate) Requires Sufficient Processing Time For Each Visitor. Consequently, If An Attendee Submits The Application Forms After The Specified Due Date And Time, The Attendee May Not Be Able To Attend The Site Visit. the Furnishing Of The Above Information, Including Your Social Security Number, Is Voluntary. However, Your Failure To Furnish All Or Part Of The Information Request May Result In The Government's Denial Of Access To The Jobsite. Any Of The Above Information Furnished By You And Protected Under The Privacy Act Shall Not Be Released Unless Permitted By Law And/or You Have Consented To Such Release. upon Receipt Of The Above Information, Our Office Will Submit A Letter To The Pass And Id Office Authorizing Your Entrance. on The Day Of The Visit, Attendees Shall Meet Promptly At The Pacific Regional Training Center (prtc) Gate And Bring Necessary Base Access Pass, The “iii Log” And “new Contractor Letter Memorandum” To The Site Visit. For Those That Do Not Have Dbids, Pick Up An Approved Day Pass From The Visitor’s Center (northgate). Attendees Shall Meet At The Visitor Control Center Overflow Parking Lot.

Details: Description Republic Of The Philippines Province Of Zamboanga Del Norte Bids And Awards Committee Provincial Capitol, Estaka, Dipolog City Email Add: Bidsandawards22@gmail.com December 05, 2024 Invitation To Bid The Provincial Government Of Zamboanga Del Norte Through The Bids And Awards Committee (bac) Is Inviting Interested Parties/ Bidders To Bid For The Following Contract: Contract Id: Pr#300(18)24-12-499(o) & 300(18)24-12-498(o) Contract Name: Procurement Of General Merchandise (hardware And Construction Supplies) Location/purpose: For The Use In The Repair & Improvement Of Primary Clinical Laboratory At Sibuco Hospital, Poblacion, Sibuco, Zamboanga Del Norte. Approved Budget For The Contract (abc): Pr#300(18)24-12-499(o) – P169,833.62 Pr#300(18)24-12-498(o) - 2,856.00 Grand Total P172,689.62 (inclusive Of All Applicable Taxes)  Bidders/contractors Must Have An Expertise In Undertaking A Similar Project, Completed At Least Two Similar Contracts Which The Equivalent Amount Is At Least 25% Of The Proposed Project For Bidding Within The Last Three Years.  Bidders Are Inform That The Delivery Term Is 30 Calendar Days Upon Receipt Of Notice To Proceed.  Bidders/ Contractors Shall Submit Their One (1) Copy Sealed Envelope Containing Their Technical And Financial Documents  Documents Submitted Must Be In Accordance With The Checklist Provided And Must Have A Corresponding Label Or Name Plates.  The Eligibility Check/ Screening As Well As The Preliminary Examination Of Bids Shall Use The Non- Discretionary "pass/ Fail" Criteria.  Post Qualification Of The Lowest/ Single Bids Shall Be Conducted.  All Particulars Relative To Eligibility Statement And Screening, Bid Security, Performance Security, Evaluation Of Bids, Post Qualification And Award Of The Contract Shall Be Governed By The Pertinent Provision Of Ra 9184 And Its Implementing Rules And Regulations (irr).  All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms In The Amount Stated In Itb Clause 14.  Bidding Is Restricted To Filipino Citizens/ Sole Proprietorships, Partnerships Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. The Schedules Of Activities Are Listed As Follows: Bac Activities Schedule Advertisement / Posting December 06 - 12, 2024 Availability And Issuance Of Bidding Documents December 06 - 13, 2024@ 08:30am Deadline For The Submission Of Bids December 13, 2024@ 08:30 Am Bid Opening And Evaluation December 13, 2024@ 09:00am  Payment For Bidding Documents Is A Non- Refundable Amount Of Five Hundred Pesos Only (php500.00) Payable To The Office Of The Provincial Treasurer, Provincial Capitol Building, Dipolog City.  Prospective Bidders May Obtain Further Information From The Office Of The Bids And Awards Committee, Provincial Capitol Building During Office Hours @ 8:00am - 5:00pm.  Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Address Stated Above.  The Provincial Government Of Zamboanga Del Norte Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders.  Bidding Documents Will Be Electronically Uploaded To The Philgeps Website Of The Provincial Office Of Zamboanga Del Norte At Bidsandawards22@gmail.com. Atty. Rafael R. Osabel, Jr. Bac Chairman Annex A: Procurement Of General Merchandise (hardware And Construction Supplies) Pr#300(18)24-12-499(o) Abc: P169,833.62 1. 41 Bags Portland Cement 2. 66.6 Kgs Dsb 10mm Ø X 6.0m (18 Pcs) 3. 270 Pcs 100 Mm Thk Chb 4. 1 Kgs Tie Wire #16 5. 15 M Pvc Pipe 50mmø, Series 1000 (5 Pcs) 6. 9 M Pvc Pipe 100mmø, Series 1000 (3 Pcs) 7. 12 Ea 2” Ø Pvc Elbow 90° 8. 8 Ea 2” Ø Pvc Elbow 45° 9. 8 Ea 2”ø X 2”ø Pvc Wye 10. 2 Ea 2”ø Pvc Clean-out W/ Plug 11. 1 Ea 2”ø Pvc Tee 12. 2 Ea 4”ø Pvc Clean-out W/ Plug 13. 4 Ea 4”ø Pvc Elbow 90° 14. 5 Ea 4”ø Pvc Elbow 45° 15. 4 Ea 4”ø X 4”ø Pvc Wye 16. 3 Ea 4”ø Pvc Coupling 17. 8 Cans Solvent Cement – 400c 18. 18 Pcs 1/2"ø Pvc Elbow 19. 7 Pcs 1/2"ø Pvc Tee 20. 3 Pcs 1/2"ø Pvc Coupling 21. 3 Pcs 1/2"ø Pvc Female Adoptor 22. 5 Pcs 1/2"ø Pvc Male Adoptor 23. 1 Pc 1/2"ø Gate Valve 24. 5 Rolls Teflon Tape 3/4” 25. 6 Pcs Pvc Pipe 13mmø, Blue 26. 3 Sets Water Closet With Complete Fittings & Accessories 27. 2 Sets Countertop Lavatory With Complete Fitting & Accessories 28. 3 Sets Stainless Floor Drain 4” X 4” 29. 3 Pcs Stainless Faucet 1/2"ø 30. 17 Pcs Fiber Cement Board 6mm 31. 20 Pcs Metal Studs 0.60mm Thk X 35mm X 76mm X 3.0m 32. 7 Pcs Metal Tracks 0.60mm Thk X 35mm X 76mm X 3.0m 33. 2626 Pcs Blind Rivets 1/8”ø X 1/2" 34. 90 Pcs Metal Screw 1” 35. 3 Sets Door Knob 36. 5.04 M² Wooden Panel Door 0.80m X 2.10m 37. 5 Sets Loosepin Hinges 4” X 4” 38. 3 Pcs 1/8” Thk X 2” X 4” Rectangular Aluminum Tube, Analoc (for Door Jamb & Header, 3-sets D-1) 39. 15.84 M² Unglazed Tiles 0.60m X 0.60m (44 Pcs) 40. 7 Bags Tile Grout 41. 1 Pc Diamond Cutting Wheel 4” 42. 38.16 M² Glazed Tiles 0.60m X 0.60m (106 Pcs) 43. 6 Bags Tile Adhesive (25kg/bag) 44. 1 M Hardware Cloth 45. 1 Gals Concrete Neutralizer 46. 2 Gals Concrete Sealer/primer 47. 2 Gals Patching Compound 48. 4 Gals Semi-gloss (two Coat) 49. 4 Pint Tinting Color (optional) 50. 2 Sets Roller Paint 6” W/pan 51. 2 Pc Paint Brush 2” 52. 1 Pc Paint Brush 4” 53. 20 Pcs Sand Paper #120 54. 3 Gals Glazzing Puty 55. 2 Gals Flatwall Enamel 56. 2 Gals Quick Dry Enamel 57. 4 Gals Paint Thinner 58. 3.78 M² 0.60m X 2.10m Pvc Door W/ Jamb & Comp. Acc., (3 Sets) 59. 1 Pc Hacksaw Blade 60. 12 Pcs Led Bulb, 12 Watts 61. 12 Pcs Receptacle Socket 2”ø Plastic 62. 2 Rolls Electrical Tape, Big Sub-total: P169,833.62 Pr#300(18)24-12-498(o) Abc: P2,856.00 1. 3.5 M3 Sand Sub-total: P2,856.00 Grand Total: P172,689.62 ***nothing Follows***

Details: Description Invitation To Bid For The Procurement Of Various Laboratory Supplies 1. The Department Of Agriculture-regional Field Office 7, Will Conduct A Public Bidding Through Early Procurement Activities (epa) Of National Expenditure Plan (nep) For Fiscal Year 2025 (gaa 2025) And Intends To Apply The Sum Of Five Hundred Thousand Pesos (₱500,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For The Procurement Of Various Laboratory Supplies. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Department Of Agriculture – Rfo 7 Is Conducting This Procurement Through The Early Procurement Activity (epa) For National Expenditure Plan (nep) For Fiscal Year 2025 (gaa 2025) To Ensure The Timely Delivery Of Goods, Implementation Of Infrastructure Projects And Rendition Of Consultancy Services Where The Procuring Entity (pe) Is Encouraged To Start Procurement Activity Short Of Award. 3. Epa Shall Refer To The Conduct Of Procurement Activities, From Posting Of The Procurement Opportunity, If Required, Until Recommendation Of The Bids And Awards Committee (bac) To The Hope As To The Award Of The Contract, For Goods To Be Delivered, Infrastructure Projects To Be Implemented And Consulting Services To Be Rendered In The Following Fiscal Year (i.e., Fy 2021), Pending Approval Of Their Respective Funding Sources. The Bidders, Therefore, Are Herewith Informed Of The Following: A. Interested Bidders Are Invited/requested To Submit Their Bid Proposals Based On Indicative Budget (i.e. Subject To Final Approval) Through This Invitation To Bid, Together With The Bidding Documents; B. The Pe Will Evaluate The Bid Proposals And Determine The Winning Bidder. The Financial Bid Proposal Of The Winning Bidder Will Be Contract Price/amount Which Is Considered Fixed Price. However, The Notice Of Award (noa) Will Only Be Issued Upon The Approval Of The Budget (i.e., Short Of Award); And C. Would There Be A Delay In The Award As Affected By The Possible Delay In The Budget Approval, The Bid Validity As Specified In The Bidding Documents (which Is A Maximum Of 120 Calendar Days), The Winning Bidder May Be Requested To Extend The Bid Validity Accordingly (that Is, Changing The Expiration Of The Original Bid Security). In Case Of The Bidder’s Refusal To Extend The Bid Validity, The Bid Submitted By Said Bidder Will Be Rejected. 4. The Department Of Agriculture-regional Field Office 7 Now Invites Bids For The Procurement Of Various Laboratory Supplies With The Following Details/specifications: 1) 30 Boxes Face Mask. Earloop, Disposable, 3-ply, Hypoallergenic, 50pcs/box @ 500.00/box 2) 20 Boxes Laboratory Grade Tissues, Paper Fiber Optic Cleaning Wipes, Lint-free, 260 Wipes/box @ 500.00/box 3) 6 Rolls Parafilm, For Glassware Seal, 4inches X 125 Ft./roll @ 3,600.00/roll 4) 12 Pcs Erlenmeyer Flask, 500 Ml, Borosilicate Glass Type 1, Thick & Durable @ 790.00/pc 5) 36 Pcs Erlenmeyer Flask, 250 Ml, Borosilicate Glass Type 1, Thick & Durable @ 500.00/pc 6) 100 Pcs Erlenmeyer Flask, 125 Ml, Borosilicate Glass Type 1, Thick & Durable @ 650.00/pc 7) 50 Pcs Funnel, Borosilicate Glass Type 1, Inside Dia. 7cm, Short-stem, Thick And Durable @ 1,300.00/pc 8) 50 Pcs Funnel, Borosilicate Glass Type 1, Inside Dia. 6.5cm, Short-stem, Thick And Durable @ 1,300.00/pc 9) 12 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 100 Ml @ 2,500.00/pc 10) 12 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 200 Ml @ 2,800.00/pc 11) 12 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 250 Ml @ 3,000.00/pc 12) 4 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 500 Ml @ 3,800.00/pc 13) 4 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 1000 Ml @ 5,300.00/pc 14) 3 Pcs Volumetric Flask, Glass-stoppered, Borosilicate Glass Type 1, 2000 Ml @ 7,000.00/pc 15) 3 Pcs Suction Flask, Glass, 500ml, Borosilicate Glass Type 1, Thick & Durable @ 2,000.00/pc 16) 12 Pcs Beaker, 250ml, With Spout, Borosilicate Glass Type 1, Thick & Durable @ 1,100.00/pc 17) 6 Pcs Beaker, 600ml, With Spout, Borosilicate Glass Type 1, Thick & Durable @ 1,400.00/pc 18) 2 Pcs Beaker, 2000ml, With Spout, Borosilicate Glass Type 1, Thick & Durable @ 5,000.00/pc 19) 4 Pcs Graduated Cylinder, 20ml, Borosilicate Glass Type 1, Thick & Durable @ 350.00/pc 20) 4 Pcs Graduated Cylinder, 50ml, Borosilicate Glass Type 1, Thick & Durable @ 520.00/pc 21) 4 Pcs Graduated Cylinder, 100ml, Borosilicate Glass Type 1, Thick & Durable @ 1,000.00/pc 22) 4 Pcs Graduated Cylinder, 500ml, Borosilicate Glass Type 1, Thick & Durable @ 2,750.00/pc 23) 40 Pcs Rubber Stopper, Top Dia. 41-45mm, Bottom Dia. 33-36mm, Height-22mm @ 70.00/pc 24) 4 Pcs Rubber Stopper, Top Dia. 50-54mm, Bottom Dia. 30-32mm, Height-30mm @ 80.00/pc 25) 2 Pcs Hydrometer, Astm No. 1.152h-type With Bouyoucos Scale In G L-1 @ 7,360.00/pc Delivery Site: Regional Soils Laboratory, Da7 Complex, Maguikay, Mandaue City, Cebu Delivery Of The Goods Is Required Within 30 Calendar Days From The Receipt Of Approved Notice To Proceed (ntp). Bidders Should Have Completed, Within Five Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 5. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non- Discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 6. Prospective Bidders May Obtain Further Information From Department Of Agriculture- Regional Field Office 7- Bac 2 Secretariat Through The Contact Details Given Below And Inspect The Bidding Documents As Posted On The Philippine Government Electronic Procurement System (philgeps). 7. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On December 13, 2024 From The Given Address Below And Upon Payment Of Non-refundable Bid Document Fee The Amount Of One Thousand Pesos (₱1,000.00) (based On Appendix 8 - Guidelines On The Sale Of Bidding Documents Of The 2016 Revised Irr Of 9184 Updated As Of January 31, 2023. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees Which Will Be Presented In Person, By Facsimile, Or Through Electronic Means. 8. The Department Of Agriculture-regional Field Office 7, Will Hold A Pre-bid Conference On December 23, 2024 -2:00 P.m. At Da Conference Room, Da Complex, Highway Maguikay, Mandaue City, Which Shall Be Open To Prospective Bidders. Electronic Pre-bidding May Not Available For This Procurement Opportunity. 9. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below On Or Before January 7, 2025 - 10:00 A.m. Late Bids Shall Not Be Accepted. 10. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 11. Bid Opening Shall Be On January 7, 2025 - 10:00 A.m. At Da-rfo 7 Conference Room, Da Complex, Highway Maguikay, Mandaue City. Bids Will Be Opened In The Presence Of The Bidders Or Bidder’s Authorized Representatives Who Choose To Attend The Activity. Electronic Bidding May Not Available For This Procurement Opportunity. 12. The Department Of Agriculture Does Not Condone Any Form Of Solicitation On Any Prospective Winning And Losing Bidders By Any Of Our Staff/employees Or Any Other Party. Any Sort Of This Kind Shall Be Reported Immediately To The Office Of The Secretary Or The National Bureau Of Investigation (nbi) For Entrapment And Proper Investigation. 13. The Department Of Agriculture Regional Field Office 7 (da-rfo 7) Reserves The Right To Reject Any And All Bids, Annul The Bidding Process, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 14. For Further Information, Please Refer To: Bac 2 / Procurement Section Department Of Agriculture Regional Field Office-7 Telefax No. 032-2682698 Or 032-345-3483 December 13, 2024 (sgd.) Rtd Wilberto O. Castillo, Ph.d. Bac Chairperson

Details: Description Technical Specifications Procurement Of Office Sports Equipment - Golf Club Equipment December 2024 1. Objectives The Objective Of Procuring A Golf Club Set For The Office Of Product Development Of Golf Tourism Is To Enhance The Deparfinent's Engagement And Representation At Various Golf Events Across The Philippines. This Will Be Achieved By Ensuring Staff Are Equipped With High-quality, Versatile Golf Clubs That Can Be Used During Invitations To Golf Events And During Ceremonial Tee-off Activities. The Golf Club Set Will Serve As A Professional Tool To Promote And Demonstrate The Department's Commitment To Golf Tourism, Fostering Stronger Relationships With Stakeholders And Showcasing The Philippines As A Premier Golf Destination. Enhance Representation: Ensure The Department Is Well-represented At Golf Events, Demonstrating A High Level Of Professionalism And Commitment To The Sport. Strengthen Stakeholder Relationships: Use The Golf Club Set To Engage With Key Stakeholders, Including Potential Investors, Partners, And Tourism Promoters. Promote Golf Tourism: Highlight The Philippines As A Top Destination For Golf Tourism By Actively Participating In Events And Ceremonial Activities. Ensure Versatility And Quality: Procure A Golf Club Set That Caters To Various Skill Levels And Playing Styles, Ensuring It Meets The Needs Of Different Staff Members Who May Use It. Boost Staff Engagement: Provide Staff With The Necessary Equipment To Participate Confidently In Golf Events, Thereby Increasing Their Involvement And Enthusiasm In Promoting Golf Tourism. 11. Minimum Requirements For Supplier: A. Must Be Accredited With The Philippine Government Electronic Procurement System (philgeps); B. Must Be Willing To Provide Services On A Send Bill Arrangement; C. The Winning Bidder Must Be Able To Comply With The Specifications Set By The End-user; D. Must Be Willing To Provide Product Warranty/retum And Exchange Of Defective Items; E. Rates Must Be Inclusive Of All Applicable Taxes And Delivery Fee; And F. Must Be Able To Produce The Materials Within The Period Agreed Upon By The Parties. 111. Compliance To Specifications/ Provisions The Winning Bidder Must Coordinate With The Dot End User To Confirm All Required Specifications Before Delivery. The Winning Bidder, However, Shall Be Deten•nined Not Solely Based On The Amount Of The Bid But Shall Also Evaluated On The Overall Compliance With The Requirements Detailed In This Technical Specification. The Winning Bidder Shall Warrant Its Performance And Guarantee That The Equipment Delivered Conforms Fully To The Stated Specifications. Any Defects, Deviations, Or Non Compliance Discovered Upon Inspection Shall Be Corrected By The Winning Bidder At Its Own Expense Immediately Upon Being Informed Thereof By The Dot End User. Iv. Scope And Work Deliverables Golf Club Eouipments Dexterity: Right Hand For Mens For Ladies Items Items Driver (1 Unit): Loft Angle: 10.5 0 Lie Angle: 56 0 -600 Length: 45 — 45.5 Inches Clubhead Material: Titanium/ Carbon Fiber (includes Headcover) Head Size: 460cc (cubic Centimeters) Shaft: Graphite Flex: Regular Distance Range: 300+ Yards 5-1ron (1 Unit) Loft Angle: 24 0—27 0 Lie Angle: 60 0-61 0 Length: 36.5 - 37.5 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 160 Yards Fairway Wood (1 Unit): #5 Loft Angle: 18 0-21 0 Lie Angle: 58 0-600 Length: 4243 Inches Clubhead Material: Stainless Steel (includes Headcover) Head Size: 140-180 Cc (cubic Centimeters) Shaft: Graphite Flex: Regular Distance Range: 200-230 Yards 6-1ron (1 Unit) Loft Angle: 27 0—31 0 Lie Angle: 61 0-62 0 Length: 36-37 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 150 Yards 5-lrons (1 Unit) Loft Angle: 21 0—25 0 Lie Angle: 60 0-61 0 Length: 37.5 - 38.5 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Re Lar 7-1ron (1 Unit) Loft Angle: 30 0—34 0 Length: 36-37 Inches Lie Angle: 62 0-63 0 Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite • Shat Flex: Re Lar • Distance Range: 200 Yards • Distance Range: 140 Yards 6-lrons (1 Unit) Loft Angle: 25 0—28 0 • Lie Angle: 61 0 -62 0 Length: 37-38 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 190 Yards 8-1ron (1 Unit) Loft Angle: 34 0—38 0 Lie Angle: 63 0—64 0 Length: 35-36 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 130 Yards 7-lrons (1 Unit) Loft Angle: 30 0—34 0 Lie Angle: 62 0-63 0 Length: 36-37 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shat Flex: Regular Distance Range: 170 Yards 9-1ron (1 Unit) Loft Angle: 38 0—40 0 Lie Angel: 64 0-65 0 Length: 34.5 - 35.5 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 120 Yards 8-lrons (1 Unit) Loft Angle: 33 0—36 0 Lie Angle: 63 0—64 0 Length: 36-37 Inches • Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 150 Yards Iron-pw (1 Unit) Loft Angle: 430—480 Lie Angle: 64 0 -65 0 Length: 34.5 -36 Inches • Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 100 Yards 9-lrons (1 Unit) Loft Angle: 38 0—42 0 Lie Angel: 64 0-65 0 Length: 35 -37inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 140 Yards Iron-sw (1 Unit) Loft Angle: 50 0-54 0 Lie Angle: 64 0 -65 0 Length: 34 - 35 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 80 Yards Irons-(pw) Pitching Wedge (1 Unit) Loft Angle: 430—480 Lie Angle: 64 0 -65 0 Length: 35 -37 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 130 Yards Irons-(sw) Sand Wedge (1 Unit) Loft Angle: 48 0—560 Lie Angle: 640 -65 0 Length: 35-36 Inches Clubhead Material: Stainless Steel/ Carbon Steel/ Titanium Shaft Material: Graphite Shaft Flex: Regular Distance Range: 100 Yards Blade Putter (1 Unit) Blade: Gun Metal, Narrow Head Design Length: 33-35 Inches (adjustable) Loft Angle: 30- 40 Lie Angle: 70 0-72 0 Material: Stainless Steel/ Carbon Steel/ Titanium • Balance: Toe-balanced Grip: Standard Cart Bag (1 Unit) Divider: 14-way Top Pockets: Mutiple Zippered Pockets Apparel Pocket: For Clothes Or Rain Gear. Cooler Pocket: Insulated For Drinks. Valuables Pocket: Fleece-lined For Watches Or Phones. Ball/accessory Pockets. Material: Durable Nylon, Polyester, Combination Of Water-resistant Properties. Base Design: Anti-slip Or Cart-locking Base Stra : Padded Sfra • Umbrella Holder: Built-in Sleeve Or 1. Ifthe Materials Or Specifications Mentioned Above Are Not Available, The Closest Alternative May Be Considered Prior To The End User's Approval; 2. It Must Be Duly Coordinated With The End Userfrom The Conceptualization Stage To Delivery. 3. Schedule Of Delivery: Four To Five (4-5) Working Days Upon Receiving The Notice Of Award. 4. Delivery Address: 351 Department Of Tourism Bldg., Sen Gil Puyat Ave., Makati City Budget The Total Budget Is Three Hundred Forty-six Thousand And Eighty- Three And 35/100 (346,083.35), Inclusive Of Delivery Charges, Applicable Taxes And Should Cover All Requirements Enumerated Above. The Winning Bidder Shall Be Determined Based On The Proposal With The Most Advantageous Financial Package Cost, Provided That The Amount Of The Bid Does Not Exceed The Above Total Budget. Vi. Payments Terms Terms Ofpaymentto The Winning Bidder Shall Be In Accordance With The Government Procedure (send Bill Arrangement). Failure To Comply With The Terms And Conditions Of The Contract Will Result In The Payment Of Corresponding Penalties And Liquidated Damages In The Amount Equal To Ten Percent (10%) Of The Contract Price By The Winning Bidder. Vll. Contact Information Ms. Claudette Ann Palomar / Ms. Lea Jane L. Maputi Product Development Of Golf Tourism And Special Projects Mobile No.: +639 469 282 817/ +639 619 844 325 Phone No.: +632 8459 5200 To 5230 Loc 428 Email Address: Pdgtsp@tourism.gov.ph Prepared By: Claud 'n T. Palomar Too I An Project Officer Oduct Velopment Of

Details: Solicitation Notice - There Are No Funds Against This Baa Solicitation W911qy-20-r-0022. Solicitation W911qy-20-r-0022is Available As Of 29 February 2020 And Is Open Until 28 February 2025. ***proposal Checklist Has Been Updated And Uploaded.*** ***baa Solicitation (updated 31 Mar 2021)and Associated Baa Templates For Submission Are Attached.*** the U.s. Armycombat Capabilities Development Command - Soldier Centerbroad Agency Announcement (baa) Identifies Scientific And Technical Areas Of Interest For Research And/or Exploratory Development. This Baa Is Conducted Using Full And Open Competition. In An Effort To Minimize Proposal Preparation Cost, This Baa Utilizes A Two-step Process. The First Step Will Be The Submission Of A Concept Paper. Offerors That Submit Concept Papers That Are Consistent With The Intent Of The Baa, And Are Of Interest To The Government Will Be Invited To Submit A Proposal (step Two). Such An Invitation Does Not Assure That The Submitting Organization Will Be Awarded A Contract. Instructions For The Submission Of A Concept Paper Are Required Prior To The Submission Of A Proposal. Failure To Follow This Two-step Process May Preclude The Chance For Award. Proposals Submitted In Response To The Baa Will Be Evaluated In Accordance With The Evaluation Criteria Set Forth In The Baa. Technical Evaluations Will Employ A Peer Or Scientific Review Process. A Proposal's Technical Evaluation And Its Importance To Agency Programs, Along With Funding Availability Are Primary Bases For Contract Award. Cost Realism And Reasonableness Shall Also Be Considered To The Extent Appropriate. Concept Papers Will Be Accepted Continuously Through 28 February 2025. This Baa Will Remain Open Continuously Through 28 February 2025. The Baa Technical Areas Of Interest Are Divided Into The Following Groups: a. Combat Feeding combat Feeding Equipment And Systems combat Ration Research And Development b. Soldier Protection And Survivability warfighter Systems Technologies 1. Integrated Protective Headborne Equipment And Injury Diagnostic/assessment Tools 2. Modular Personal Protection Equipment (mppe) And Injury Diagnostic/assessment Tools 3. Chemical/biological Protection For Individuals 4. Flame And Thermal Protection For The Individual Soldier 5. Counter Surveillance 6. Body Worn Interactive Materials 7. Materials Nanotechnology 8. Advanced Protection, Integration Technologies/systems And Assessment Methods 9. Integrated Sound, Light And Blast Management For The Ears And Eyes textile Technologies 1. Multi‐functional Materials 2. High Performance Multi‐component Fibers modeling And Simulation 1. Individual Ground Soldier And Small Unit Operational Effectiveness And Survivability c. Soldier Performance Optimization 1. Body‐worn Systems, Hand Held Devices, Smart‐lightweight Electronic Components, And Information processing To Increase Soldier Maneuverability And Protection Through On‐soldier Sensing, Remote Sensing, and Knowledge Management 2. Biomechanics 3. Anthropometry 4. Warrior Performance 5. Soldier Power Sources, Power & Data Distribution And Management 6. Future Warrior Technology Integration 7. Technology Assessment And Simulation Tools 8. Ecological Approach To Warfighter Survivability; Perception‐action‐cognition 9. Soldier Centric Sensors, Information Portrayal, & Data Management Technologies 10. Soldier/squad Performance Optimization 11. Human Factors d. Expeditionary Maneuver Support And Field Service Technologies 1. Research And Development 1.2 Chemical Biological Radiological Nuclear (cbrn) Protection 1.3 Electromagnetic Interference/electromagnetic Pulse (emi/emp) Protection 1.4 Environmental Protection And Energy Efficiency 1.5 Detection Avoidance 2. Maneuver And Movement/sustainment: Deployment/durability 3. Functional Integration Of Multiple Technologies 4. Miscellaneous 5. Unit/organization Equipment e. Aerial Delivery advanced Personnel And Cargo Airdrop Systems f. Simulation And Training Technology embedded Training (et) live Training Simulation Of Tactical Weapon System Lethality medical Simulation And Training advanced Interactive Simulation cyber Warfare For Training (cywar‐t) adaptive Instructional Systems battlespace Visualization And Interaction synthetic Environments dismounted Soldier Research contracting Office Address: acc-apg- Natick, Natick Contracting Division, Building 1, General Greene Avenue, Natick, Ma 01760-5011

Details: Description The Zamboanga Peninsula Polytechnic State University Through Its Bids And Awards Committee (bac) Is Inviting Philgeps Registered Suppliers To Apply For Eligibility And To Submit Bids For The Items Listed Below: 1 Portland Cement, 40kg (710 Bags) 2 Coarse Sand (32 Cu.m.) 3 Gravel, ¾” Size (41 Cu.m.) 4 Fine Sand (18 Cu.m.) 5 Cement Water-proofing Compound, 1kg/bag (40 Bags) 6 Chb, 4” (4,365 Pcs.) 7 Rsb, 10mmø (585 Pcs.) 8 Rsb, 12mmø (190 Pcs.) 9 Rsb, 16mmø (180 Pcs.) 10 Dry Brickstone, Sorsogon (10.8 Sq.m.) 11 Concrete Neutralizer (10 Gals.) 12 Liquid Tile Primer (20 Gals.) 13 Patching Compound, 20kg (25 Bags) 14 Liquid Tile Top Coat, White (40 Gals.) 15 Baby Roller, Cloth (8 Pcs.) 16 Paint Roller, 6”, Cloth (8 Pcs.) 17 Paint Brush, 3” (8 Pcs.) 18 Waterproofing Paint, Gray (4 Gals.) 19 Pvc Sanitary Pipe, S1000, 4” (12 Pcs.) 20 Pvc Sanitary Pipe, S1000, 3” (5 Pcs.) 21 Pvc 90° Sanitary Elbow, 3” (8 Pcs.) 22 Wall Faucet Plain Bib, ½” X 6”, Stainless (7 Pcs.) 23 Wall Faucet Plain Bib, ½” X 4”, Stainless (6 Pcs.) 24 Wall Faucet Plain Bib, ½” X 2”, Stainless (18 Pcs.) 25 Stainless Floor Drain Main, 6” X 6” (13 Pcs.) 26 Stainless Floor Drain Main, 6” X 4” (2 Pcs.) 27 Pvc P-trap, S1000, 4”, Assembled (10 Pcs.) 28 Body Filler W/ Hardener (12 L) 29 Tee Reducer, 4” X 2” (20 Pcs.) 30 Pvc Elbow, 45°, 2” (10 Pcs.) 31 Pvc Tee, 4”, Sanitary (40 Pcs.) 32 Pvc Elbow, 90°, 4” (15 Pcs.) 33 Pvc Wye W/ Clean-out, 4”, 4” X 4” (10 Pcs.) 34 Ppr Pipes, Red Line, ½” (13 Pcs.) 35 Ppr Tee, ½” (40 Pcs.) 36 Ppr Elbow, ½” (50 Pcs.) 37 Solvent Cement, 400cc (2 Pcs.) 38 Water Closet W/ Trap, Flush Tank & Cover, White Porcelain (8 Sets) 39 Wall-mounted Urinal, White Porcelain, W/ Push Button Faucet Valve (7 Sets) 40 Surface Lavatories, Round & White, For Counters (7 Sets) 41 Cylindrical Knobset (4 Sets) 42 Sliding Barrel Flat Bolt, Stainless, 3” (8 Sets) 43 2-prong Universal Outlets (4 Sets) 44 Electrical Flexible Hose, 1/2” (60 M) 45 Electrical Tape, 16m, Big Size (4 Pcs.) 46 Junction Square Box W/ Cover (6 Pcs.) 47 Panel Board, 8 Branches (1 Set) 48 Utility Box (7 Pcs.) 49 Orbit Fan (2 Units) 50 Circuit Breaker, 30a (1 Pc.) 51 Circuit Breaker, 15a (2 Pcs.) 52 Led Downlight, White, 9w, 145mm X 145mm, 3 Colors (21 Pcs.) 53 Thhn Wire #12 (2 Boxes) 54 Thhn Wires #10 (1 Box) 55 2-gang Switch (2 Sets) 56 1-gang Switch (2 Sets) 57 4-gang Switch (1 Set) 58 Gi Tubular, 2” X 4” (20 Pcs.) 59 Stainless Zppsu Seal, 1.5m Ø (1 Set) 60 Fiber Cement Board, 3.5mm (40 Pcs.) 61 Double Metal Furring (145 Pcs.) 62 Cut-off Wheel Blade, 14” (4 Pcs.) 63 Angle Grinder Cutting Disc (20 Pcs.) 64 Mirror W/ Brown Aluminum Framing, 80cm H X 60cm W (1 Pc.) 65 Mirror W/ Brown Aluminum Framing, 80cm H X 200cm W (2 Pcs.) 66 Wall Angle, 0.4mm (35 Pcs.) 67 Filling Materials, No Boulders & Big Rocks (120 Cu.m.) 68 Door Bumper (4 Pcs.) 69 Stainless Toilet Signages, Male & Female (1 Pc.) 70 Stainless Toilet Signages, Male (1 Pc.) 71 Stainless Toilet Signages, Female (1 Pc.) 72 Stainless Toilet Signages, Pwd (1 Pc.) 73 Stainless Door Hinges, 3” X 3” X 2mm, Set Of 2 (8 Sets) 74 Stainless P-trap, For Lavatory (7 Sets) 75 Stainless Bidet, Chrome-plated, Spray (14 Sets) 76 Gi Welding Electrode (20 Kgs.) 77 Sanitary Pipes, S1000, 2” (12 Pcs.) 78 Louver-type Solid Panel Door, 1000 X 2100 X 40, Gloss Choco Brown (1 Set) 79 Louver-type Solid Panel Door, 700 X 2100 X 40, Gloss Choco Brown (1 Set) 80 Louver-type Solid Panel Door, 800 X 2100 X 40, Gloss Choco Brown (2 Sets) 81 Louver-type Solid Cafe Door, 500 X 1600 X 40, Gloss Choco Brown (7 Sets) 82 Door Jamb, Good Quality, 1m (1 Set) 83 Door Jamb, Good Quality, 0.7m (1 Set) 84 Door Jamb, Good Quality, 0.8m (2 Sets) 85 Door Jamb, Good Quality, 0.5m (7 Sets) 86 Stainless Flexible Hose, ½” X 12” (9 Pcs.) 87 Angle Valve, 2-way (8 Pcs.) 88 Angle Valve, Single (7 Pcs.) 89 Metal Single Robe Hook (12 Pcs.) 90 Stainless Steel Welding Electrode (5 Kgs.) 91 Non-slippery Porcelain Light Gray Tiles, 60” X 60” (197 Pcs.) 92 Glossy White Tiles, 30” X 60” (712 Pcs.) 93 Granite Slab, 60mm X 220mm (3 Pcs.) 94 Tile Adhesive, 25kg/bag (20 Bags) 95 Tile Grout, White, 2kg/bag (30 Bags) 96 Stainless Steel Tube, 2” Ø (12 Pcs.) 97 Stainless Steel Pipe Fitting, 90°, 2” Ø (12 Pcs.) 98 Pwd Stainless Grab Bar (3 Sets) 99 Awning-type Window W/ Analok Framing, 0.5m X 0.5m, Refer To Plan (8 Sets) 100 Awning-type Window W/ Analok Framing, 0.5m X 1.5m, Refer To Plan (4 Sets) 101 Common Wire Nails, 2”, 10kg/bag (2 Boxes) 102 Common Wire Nails, 3”, 10kg/bag (2 Boxes) 103 Common Wire Nails, 4”, 10kg/bag (3 Boxes) 104 Concrete Nails, 4”, 10kg/bag (1 Box) 105 Coco Lumber, 2” X 2” X 12’ (150 Pcs.) 106 Coco Lumber, 2” X 3” X 12’ (150 Pcs.) 107 Phenolic Board (20 Sheets) 108 Pvc Vertical Tank, 2000l (2 Pcs.) 109 Pvc Horizontal Tank, 1000l (1 Pc.) 110 Water Pump, 0.75hp (1 Set) 111 Bladder Tank, 20l (1 Set) 112 Pressure Gauge (1 Pc.) 113 Float Ball Valve (2 Pcs.) 114 Ppr Gate Valve, ½” (3 Pcs.) 115 Ppr Check Valve, ½” (4 Pcs.) 116 Double Float Suspension (3 Pcs.) 117 Ppr Pipe, ¾” Ø, Red Line (8 Pcs.) 118 Sanitary Coupling, 4” Ø (13 Pcs.) 119 Ppr Female Elbow, ½”, Metal Thread (45 Pcs.) 120 Ppr Coupling, ½” (25 Pcs.) 121 Ppr Ball Valve, ½” (2 Pcs.) 122 Ppr Ball Valve, ¾” (2 Pcs.) 123 Electric Impact Drill, Heavy-duty, Good Quality, 750w Min. (2 Units) 124 Angle Grinder, Heavy-duty, Good Quality, 710w Min. (2 Units) 125 Tie Wire #16 (50 Kgs.) 126 Glazing Putty (5 Gals.) 127 Flat Wall Enamel (10 Gals) 128 Enamel Quick-dry, White (10 Gals.) 129 Paint Thinner (5 Gals.) 130 Liquid Tile Tinting Color, Venetian Red, Full Tone (6 Pints) 131 Liquid Tile Tinting Color, Raw Sienna, Full Tone (6 Pints) 132 Liquid Tile Tinting Color, Hansa Yellow, Full Tone (6 Pints) 133 Liquid Tile Tinting Color, Bulletin Red, Full Tone (6 Pints) Note: For Details On Door & Window Dimensions & Specifications, Please Refer To The Pdmeo (project Development Management & Evaluation Office). ______________________________ Supplier’s Signature Over Printed Name The Schedule Of Bac Activities Is As Follows: 1. Pre-bid Conference - December 23, 2024, @ 10:00a.m. 2. Receipt And Opening Of Bids - January 6, 2025, @ 10:00a.m. 3. Bid Evaluation - January 7-14, 2025 4. Post-qualification - January 7-14, 2025 5. Issuance Of Notice Of Award - January 15, 2025 6. Contract Preparation & Signing - January 16, 2025 7. Issuance Of Notice To Proceed - January 16, 2025 The Criteria To Be Used For The Eligibility Check Of Prospective Bidders, Examination And Evaluation Of Bids, Post-qualification And All Matters To This Procurement Shall Be Under Republic Act No. 9184 (the Government Procurement Reform Act) And Its Implementing Rules And Regulations. Interested Bidders May Obtain Further Thank Important Notice To Bidders: 1. Bidding Documents May Be Acquired By Interested Bidders From The Address Below And Upon Payment Of A Non-refundable Fee For The Bidding Documents Of Five Thousand Pesos (p 5,000.00). It May Also Be Downloaded From The Website Of The Philippine Government Electronic Procurement System (philgeps), Provided That Bidders Shall Pay The Non-refundable Fee For The Bidding Documents Not Later Than The Submission Of Their Bids. 2. All Bidders Are Required To Post A Bid Security In The Form Of A Cash/bank Guarantee (2% Of Abc) Or Surety Bond (5% Of Abc) Or Bid Securing Declaration. 3. The Bidder Shall Prepare An Original Technical And Financial Proposal, Copy 1 And Copy 2. 4. State The Shortest Time Of Delivery And Submit Your Quotation Duly Signed By Your Representative In A Sealed Envelope. 5. Warranty Shall Be For Three (3) Months For Supplies And Materials. One (1) Year For Equipment From The Date Of Acceptance By The Procuring Agency. 6. All Erasures Must Be Initialed To Avoid Disqualifications. 7. Late Submission Of Bids Will Not Be Accepted. Approved By: (sgd.) Jocelyn P. Remoto Bac Chairperson The Zamboanga Peninsula Polytechnic State University Reserves The Right To Reject Any Or All Bids, Accept The Bid Most Advantageous To The Government, And Award The Contract By Lot.

Details: Description Technical Specifications I. Project Request For Procurement Of Opaa Office Equipment Ii. Minimum Requirements 1. Must Be Registered With The Philippine Government Electronic Procurement Systems (philgeps). 2. Must Provide A Breakdown Of Prices And Services Included In The Quotation. 3. Quotation To Include E-vat And Other Government Taxes. 4. Amenable To Government Procedures Or Send-bill Arrangement. Iii. Scope Of Work/deliverables 1. Provide The Office Equipment For Official Use Of The Office Of Public Affairs And Advocacy (opaa). Date Of Delivery : 45 Days Upon Acceptance Of Purchase Order Venue Of Delivery : Department Of Tourism General Services Division G/f, New Dot Bldg., 351 Sen. Gil Puyat Ave., Makati City Time : Office Hours 2. These Equipment Will Be Used To Support The Department Of Tourism’s Photo And Video Documentation, Editorial, Video Production, Social Media Management And Support To Operations Of The Department. Lot Equipment Quantity Lot #1 Zoom Lens (wide Lens 17-40mm F/4l Usm, Ef Mount) ● Aperture Range - Wide / Long F/4.0-22 ● Number Of Aperture Blades 7 ● Filter Size 77mm Note: For Existing Equipment Of The Team (canon) 2 Pcs Lens (zoom Lens 18-150mm F/3.5-6.3 Is Stm, Rf Mount) ● Focal Length 18 To 150mm (35mm Equivalent Focal Length: 29 To 240mm) ● Maximum Aperture F/3.5 To 6.3 ● Minimum Aperture F/40 ● Lens Format Coverage Aps-c ● Angle Of View 74° 20' To 10° 25' ● Minimum Focus Distance 6.7" / 17 Cm ● Maximum Magnification 0.44x ● Optical Design 17 Elements In 13 Groups ● Diaphragm Blades 7, Rounded ● Focus Type Autofocus ● Filter Size 55 Mm (front) ● Dimensions (ø X L) 2.7 X 5" / 69 X 126.7 Mm ● Weight 10.9 Oz / 310 G Note: For Existing Equipment Of The Team (canon) 1 Pc Lens (wide Lens 18-45mm F/4.5-6.3 Is Stm, Rf Mount) ● Maximum Aperture F/4.5 To 6.3 ● Minimum Aperture F/32 ● Lens Mount ● Lens Format Coverage Aps-c ● Angle Of View 74° 20' To 33° 40' ● Minimum Focus Distance 7.9" / 20 Cm ● Maximum Magnification 0.16x ● Optical Design 7 Elements In 7 Groups ● Diaphragm Blades 7, Rounded ● Focus Type Autofocus ● Filter Size 49 Mm (front) ● Dimensions (ø X L) 2.7 X 1.7" / 68.9 X 44.3 Mm ● Weight 4.6 Oz / 130 G Note: For Existing Equipment Of The Team (canon) 1 Pc Lens Extender Ef1.4x Iii ● Ef Mount Teleconverter ● 1.4x Magnification Factor ● Microcomputer Controlled ● Communication Between Lens & Camera ● Spectra Coating Reduces Ghosting/ Flare ● Protective Fluorine Coating ● Dust And Water Resistant ● Compatible With Select Ef Mount Lenses Note: For Existing Equipment Of The Team (canon) 1 Pc Lens Adapter (rf To Ef Mount) ● Mount Specification Ef Mount (camera Side); Rf Mount (lens Side) ● Usable Lensef Lenses; Excludes Rf Lenses, Ef-m Lenses, Cn-e Lenses (ef Cinema Lenses) ● Usable Camera Eos R Camera ● Dust- & Water-resistance Provided (rubber Ring) ● Dimensions Φ2.80 X 0.94 In. / Φ71.2 X 24mm (adapter Only) ● Weight Approx. 3.9 Oz. / 110g (adapter Only) Note: For Existing Equipment Of The Team (canon) 3 Pcs Dslr Gimbal Stabilizer ● Compatibility - Mobile App: Yes: Android & Ios App Name: Ronin App ● Load Capacity - 3kg ● Mount - 1 X 1/4"-20 Female; 2 X Nato Rail ● Material - Aluminum Alloy Note: For Existing Equipment Of The Team (rs4 Pro) 2 Pcs Drone Battery ● For Dji Mini 4 Pro Drones ● 2590 Mah Power Capacity ● Up To 34 Minutes Of Flight Time ● 58 To 70 Minutes Of Charging Time ● Note: For Existing Equipment Of The Team (mini 4 Pro) 5 Pcs Camera Battery (lp-e6nh) ● Battery Capacity 2130 Mah ● Output Voltage 7.2 Vdc ● Battery Chemistry Lithium-ion ● Dimensions 2.24 X 1.51 X 0.83" / 56.8 X 38.4 X 21 Mm Note: For Existing Equipment Of The Team (canon) 4 Pcs Camera Battery Pack (lp-e17) ● Item Dimensions L X W X H 2.76 X 3.54 X 1.97 Inches ● Item Weight 0.05 Kilograms ● Amperage 1040 Milliamps ● Battery Capacity ‎1040 Milliamp Hours Note: For Existing Equipment Of The Team (canon) 20 Pcs Camera Charger (2 Lp-e6nh) For Lp-e6nh ● Dual Charger With 2 Charging Ports To Quickly Charge Two Lp-e6nh Batteries At The Same Time ● Charger Has 2 Input Options, The Included Usb Type-c Or The Older Micro Usb Interface Can Also Be Used Note: For Existing Equipment Of The Team (canon) 4 Pcs Camera Flash (ttl Li-ion Round Head Camera Flash) ● 330-degree Rotation And 120+ Degree Tilt ● Full Power Recycle Time Of Fewer Than 1.5 Seconds ● Approximately 650 Full Power Flashes Per Charge ● Zooming Head With Automatic Zoom Or Manual Control ● High Speed Sync For Shutter Speeds Up To 1/8000 Second Note: For Existing Equipment Of The Team (v1 Pro Speedlight) 4 Pcs Camera Mic (wireless Mic) ● 250m (820 Ft.), Range ● 15-hour Battery ● Oled Touchscreen ● 14-hour Recording Note: For Existing Equipment Of The Team (dmt02) 2 Pcs Phone Gimbal Stabilizer ● Portable And Foldable ● Activetrack 6.0 ● Built-in Extension Rod ● Magnetic Quick Release Design ● Bluetooth 5.1 Support ● Usb Type-c Power Input Note: For Existing Equipment Of The Team (osmo Mobile 6) 2 Pcs Light-weight Tripod ● Head Type Fluid Head ● Drag Control Yes ● Primary Material Aluminum ● Load Capacity 22 Lb / 9.98 Kg ● Maximum Working Height 61.06" / 155.1 Cm ● Minimum Working Height 30.8" / 78.2 Cm ● Closed Length 32.5" / 82.5 Cm ● Weight 7.94 Lb / 3.6 Kg ● Camera Attachment ● Head Type Fluid Head ● Base Mount 75 Mm Half Ball ● Pan & Tilt ● Drag Control Yes ● Independent Pan Lock Yes ● Independent Tilt Lock No ● Vertical Tilt +90° To -75° ● Legs ● Primary Material Aluminum ● Leg Lock Twist Lock ● Leg Sections 3 ● Foot Features Spiked, Retractable ● General ● Load Capacity 22 Lb / 9.98 Kg ● Maximum Working Height 61.06" / 155.1 Cm ● Minimum Working Height 30.8" / 78.2 Cm ● Closed Length 32.5" / 82.5 Cm ● Accessory Mounting 1x Pan Handle Fitting ● Bubble Level Yes ● Spreader Support Mid-level (integrated) ● Weight 7.94 Lb / 3.6 Kg ● Packaging Info ● Package Weight 11 Lb ● Box Dimensions (lxwxh) 39.5 X 6.5 X 6.5" Note: For Existing Equipment Of The Team (befree Gt Xpro Carbon Fiber) 3 Pcs Studio Light (2800k - 6500k)(100w) ● Color Temp: 2800-6500k, Cri/tlci: 96/97 ● 100-240 Vac, 32 Channels, 16 Groups ● Bowens Front Accessory Mount Note: For Existing Equipment Of The Team (amaran 200x S) 3 Pcs Softbox Parabolic ● Shape Parabolic Note: For Existing Equipment Of The Team (light Dome Se) 3 Pcs Studio Light Stand Stainless Steel ● 12ft Pro Light Stand (air Cushion) ● Butterfly Light Stand 3.7m Air Cushioned Pro Light Stand ● Folded Length: 106cm ● Max Height: 370 Cm ● Tube Diameters: 40/35/30/25mm ● Tip: 1/4″ Screw Or 3/8″ Screw Note: For Existing Equipment Of The Team (heavy-duty Air-cushioned Light Stand) 3 Pcs Boom Mic (dslr,fixed Tube With Reduced Visual Appearance And Easy Handling (camera- Or Boom-mounted) ● Flat, Wide-range Frequency Response For Exceptionally Clean And Natural Reproduction Of Both Music And Speech ● Superior Rejection Of Electromagnetic Hum, Optimized For Shielding Against Broadband Interference Emitted By Computer Monitors ● Internal “air Suspension” Shock Isolation Virtually Eliminates Mechanical Noise Transmission ● Highly Effective Pop Filter Eliminates Need For Any Add-on Protection Against Explosive Breath Sounds, Even For Close-up Vocals Or Narration ● Classic Cardioid Polar Pattern, Uniform With Frequency And Symmetrical About Axis, To Provide Maximum Rejection And Minimum Coloration Of Off-axis Sound Note: For Existing Equipment Of The Team (sm7db) 1 Pc Camera Bag (35x24x62cm) ● Fits Pro Mirrorless Or Dslr With 70-200mm, 4-5 Extra Lenses ● Maxfit Divider System For Maximum Capacity & Snug Protective Fit ● Space For 15'' Laptop, 10'' Tablet, Plus Wacom Type Tablet ● Carry-on Ready: Meets Standard Carry-on Requirements ● Travel Friendly: Stowable Shoulder Straps, Removable Waist Belt ● Weight 2.39 Kg ● External Dimensions 32 X 25 X 48 Cm ● Tablet Compartment Dimensions 21.5 X 1.5 X 24 Cm ● Internal Dimensions 28 X 15 X 42 Cm Note: For Existing Equipment Of The Team (pro Trekker Bp 350 Aw Ii) 2 Pcs Subtotal Php 656,030.28 Lot #2 Mic Boom Stand ● Height: 1070 Mm - 2400 Mm (42.1" - 94.5") ● Weight: 2.6 Kg (5.7 Lbs.) ● Boom Length: 780 Mm (30.7") ● Folded Size: 980 Mm X 95 Mm X 95 Mm (38" X 3.7" X 3.7") Note: For Existing Equipment Of The Team (mc-125 Pro Mic Boom Stand) 1 Pc Camera Hard Case (28x13x48cm) ● Weight: 1 Kg ● Total Volume: 25.5 L ● Internal Dimensions: 28 X 13 X 48 Cm ● External Dimensions: 29 X 18.5 X 49 Cm ● Camera Compartment Dimensions: 16.5 X 9.5 X 24 Cm ● Laptop Compartment Dimensions: 27 X 2 X 41 Cm ● Primary Device Camera ● Device Volume: 4.5 L ● Exterior Material ● 300d Polyester Ripstop (recycled), 600d Polyester Solution Dyed ● Interior Material ● 200d Polyester (recycled) Note: For Existing Equipment Of The Team (trekker Lite Bp 250 Aw) 2 Pcs Camera Cage ● Battery Plate Type No ● Accessory Mounting Cage Multiple 1/4"-20 Female Thread Multiple 3/8"-16 Female Thread 1x Arri Anti-twist 3/8"-16 Female Thread 1x Qd (quick Detach) ● Camera Mounting 1/4"-20 Male Screw ● Tripod Mounting ● Cage 1/4"-20 Female Thread, 3/8"-16 Female Thread, Built-in Arca-type Plate ● Cage Built-in Arca-type Plate ● Shoe Mounting Cage, Top 1x Cold Shoe ● Materials Aluminum ● Dimensions 5.8 X 4.1 X 2.8" / 146.8 X 103.7 X 70.8 Mm ● Weight 5.5 Oz / 156 G Note: For Existing Equipment Of The Team (smallrig "black Mamba") 1 Pc Subtotal P 22,903.13 Lot #3 Heavy Duty Tripod (dslr, Aluminum Alloy) ● Variable Fluid Drag System On Pan And Tilt Movements. ● 4kg Pre-set Counterbalance System On Tilt Movement. ● Sliding Plate For The Fastest Camera Connection. ● Levelling Bubble Makes Setup Simple. ● Aluminium Telescopic Twin Leg Tripod Keeps Your System Firm. Note: For Existing Equipment Of The Team (mvk502am-1 502 Fluid) 3 Pcs Video Transmitter Battery ● Video I/o Transmitter: 1x Hdmi 1.4b Input Transmitter: 1x Bnc (3g-sdi) Input Receiver: 1x Hdmi 1.4b Output Transmitter: 1x Bnc (3g-sdi) Output ● Embedded Audio Hdmi/sdi ● Latency 50 Ms ● Video Format Hdmi Uhd 4k: 30/29.97/25/24/23.98 1080p: 60/59.94/50/30/29.97/25/24/23.98 1080i: 60/59.94/50 720p: 60/59.94/50 Sdi 1080p: 60/59.94/50/30/29.97/25/24/23.98 1080i: 60/59.94/50 720p: 60/59.94/50 ● Power Consumption Transmitter: 11 W Receiver: 8 W ● Mounting 1/4"-20 Female Note: For Existing Equipment Of The Team 2 Pcs Action Camera Accessories (waterproof Dome Port) ● Color: Black / Yellow ● Material Of Construction Plexiglass, Pc Resin, Naval-grade Stainless Steel ● Dimensions: 7.3 X 7.3 X 4" / 185 X 185 X 102 Mm ● Weight : 14.8 Oz / 420 G Note: For Existing Equipment Of The Team (telesin Waterproof Dome) 1 Pc Subtotal P 62,339.63 Grand Total P 741,273.04 Iv. Payment Procedure: Government Procedure And Is Subject To Appropriate Government Taxes. V. Approved Budget For The Contract Seven Hundred Forty One Thousand Two Hundred Seventy Three And 04/100 (php 741,273.04) Total Budget Shall Be Charged Against The Approved 2024 Wfp Of Opaa - Inclusive Of All Applicable Taxes, Government Procedure, And Send Bill Arrangement. Vi. Project By The Office Of Public Affairs And Advocacy (opaa) For Further Information, Please Refer To The Following Project Officer Below At Telephone Numbers (2) 459-5200, Loc. 316. Project Officer - Jhorica Jhane P. Hernandez - Information Officer I Note: The Winning Bid Shall Be Determined Based On The Best Package Suited To The Market At The Most Advantageous Financial Cost, Provided That The Amount Of Bid Does Not Exceed The Above Total Budget. Prepared By: Jhorica Jhane P. Hernandez Information Officer I 09672071640 Jjphernandez@tourism.gov.ph Noted By: Atty. Glenn Albert M. Ocampo Oic-director Office Of Public Affairs And Advocacy (opaa)